119529
7
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
MANUAL RELEASE MECHANISM
The Manual Release mechanism is a built-in release
device of the 412 Operator (see Figure 4). To access the
keyhole, remove the plug on the top of the motor
housing. Then insert the key and turn it a half turn in
the direction of the gate’s closing to disengage the
operator’s motorized operation. You can now move the
gate leaf by hand to open or close the gate. Operating
the gate leaf by hand is necessary during installation
and is useful during power failures.
I
NSTALLING THE OPERATOR
Once you have prepared the gate, you are ready to
proceed with the installation of the operator.
Follow the instructions below to install your operator
whether in an inward or outward swinging
configuration.
Installing the operator consists of the following steps:
Establishing the orientation of each gate leaf and its
operator.
Attaching the rear mounting bracket
Attaching the operator to the rear mounting bracket
Attaching the front mounting bracket to the
operator
Page 7
January, 2004
412 Operator And
455 D Control Panel Installation Manual
Figure 4. Use the Manual Release key to disengage the
412 Operator from its motor so that you can move the
gate leaf by hand in the opening or closing direction
Attaching the front mounting bracket to the gate
leaf
Attaching the operator’s protective cover
Installing the 455 D control panel
Adjusting the torque for the operator
Setting the operating controls
ESTABLISH THE ORIENTATION OF THE
O
PERATOR AND THE GATE LEAF
Before you begin mounting brackets or attaching parts,
you first need to establish the proper orientation of
each operator in relation to its gate leaf.
Figure 2 (page 5) shows a biparting gate from the side
where the operators are mounted. The operator
attached to the hinge on the left of the gate must be an
SX model. If the hinge is on the right side, the DX
model must be installed.
Installing the operator on the wrong side makes it
impossible to install the protective cover of the
operator.
ATTACH THE REAR MOUNTING
B
RACKET
Inward swinging gate:
You need to determine whether to attach the rear
mounting bracket directly to the post (or wall) or to
notch the post and install a recessed liner. Large pillars
require a recessed liner to house the rear mounting
bracket and part of the operator so that the pillar will
not interfere with the swing of the gate when it is fully
opened.
To determine whether you need a recessed liner,
measure the distances B and D (shown in Fig. 5) on your
gate. If your measure of B or D is greater than the
dimensions shown for your operator in Figure 5, notch
the post and construct a recessed liner for the post
mounting bracket (see Figure 6). The recessed liner
should be constructed of 3/16 or 1/4 in. steel with a
minimum interior height of 11 13/16 in. (30 cm) so as
to allow you to meet the required dimensions shown in
Figure 5. Make sure the recessed liner is securely
embedded in the post (or wall).
There are two parts to the rear mounting bracket. The
horizontal bracket attaches to the operator, and the
slotted vertical plate attaches to the gate post (see
Figure 8). Weld the two parts together and bolt the
assembly to the gate post of column. Note, though, that
use of the vertical rear mounting plate is optional.
Once you have positioned the rear mounting bracket,
attach the bracket to the post (or wall or recessed liner),
making sure the dimensions on your gate system match
those shown in Figure 5.
Figure 3.
Positive Stops
Remove the plug
on the top of the
motor housing
1.
Insert the Manual Release
key and turn it in the
direction of the gate’s
closing
2.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

FAAC-455

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw FAAC 455 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van FAAC 455 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,82 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van FAAC 455

FAAC 455 Gebruiksaanwijzing - Nederlands - 12 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info