- 15 -
• The anti-grease filters capture the grease particles suspended in the
air, and are therefore subject to clogging according to the frequency of
the use of the appliance.
In order to prevent fire hazard, it is recommendable to clean the filter
at a maximum of 2 months by carrying out the following instructions:
- Remove the filters from the cooker hood and wash them in a solution
of water and neutral liquid detergent, leaving to soak.
- Rinse thoroughly with warm water and leave to dry.
- The filters may also be washed in the dishwasher.
The aluminium panels may alter in colour after several washes. This
is not cause for customer complaint nor replacement of panels.
• The active carbon filters purify the air that is replaced in the environ-
ment. The filters are not washable nor re-useable and must be re-
placed at maximum every four months. The saturation of the active
carbon filter depends on the frequency of use of the appliance, by the
type of cooking and the regularity of cleaning the anti-grease filters.
• Clean the fan and other surfaces of the cooker hood regularly using
a cloth moistened with denatured alcohol or non abrasive liquid deter-
gent.
• The illumination installation is designed for use during cooking and
not for prolonged general illumination of the environment. Prolonged
use of the illumination installation notably reduces the duration of the
bulb.
COMMANDS: (Fig.11)
Push-button A = on/off lights switch
Push-button B = on/off cooker hood switch. The appliance switches
on at speed level 1, If the cooker hood is on depress the push-button
for 2 sec. to switch off the cooker hood. If the cooker hood is at speed
level 1 it will not be necessary to depress the push-button to switch the
cooker hood off. Decreases the motor speed.
Display C = indicates the motor speed level selected and activates the
timer.
Push-button D = switches on the cooker hood. Increases the motor
speed. Touching the key at 3rd speed, the intensive function runs for
10', then the appliance go back to work at the original speed. During this
function the display blinks.
Key E = The Timer times the functions on activation for 15 minutes,
after which they are switched off. The Timer is deactivated by re-
pressing Key E. When the Timer is activated the decimal point must
flash on the display. The Timer cannot be activated if the intensive
speed is functioning.
The “clean air” function is activated by pressing key E for 2 seconds
when the appliance is switched off. This switches the motor on for 10
minutes every hour at the first speed. During functioning a rotary move-
ment of the peripheral segments must be visualised on the display.
When this time has passed the motor switches off and the fixed letter
“C” must be visualised on the display until the motor re-starts after 50
minutes for another 10 minutes and so on. Press any key apart from the
light keys to return to normal functioning. Press key E to deactivate the
function.
• Active carbon/grease filter saturation:Fig.11
- When display item C flashes, at a speed where it alternates with the
letter F (e.g. 1 and F), the grease filters must be washed.
- When display item C flashes, at a speed where it alternates with the
letter A (e.g. 1 and A), the carbon filters must be replaced.
After the clean filter has been positioned correctly, the electronic memory
must be reset by pressing button A for approximately 5 seconds, until
the indication F or A shown on the display C stops flashing.
• COMMANDS: ELECTRONIC (Fig.10 A):
A = LIGHT
B = OFF/SPEED I
C = SPEED II
D = SPEED III
E = A
UTOMATIC STOP TIMER – 15 minutes (*)
F = FIL
TER SATURATION RESET LIGHT
When the “filter saturation” light flashes, the anti-grease filters must be
washed. When the light comes on without flashing, the anti-grease
filters must be washed and the carbon filters replaced (in case of op-
eration whit the recycling version).
When this operation has been completed, press the key to reset it.
• COMMANDS:
(Fig.9A) LUMINOUS
(Fig.10B) ELECTRONICthe key symbols are explained below:
A = LIGHT
B = OFF
C = SPEED I
D = SPEED II
E = SPEED III
F = AUTOMATIC STOP TIMER - 15 minutes (*)
• If your appliance does not have the INTENSIVE speed function, press
key E for two seconds and it will be activated for 10 minutes after which
it will return to the previously set speed. When the function is active the
LED flashes. To interrupt it before the 10 minutes have expired press
key E again.
• By pressing key F for two seconds (with the hood switched off) the
“clean air” function is activated. This function switches the appliance
on for ten minutes every hour at the first speed. As soon as this function
is activated the motor starts up at the first speed for ten minutes, During
this time key F and key C must flash at the same time.
After ten minutes the motor switches off and the LED of key F remains
switched on with a fixed light until the motor starts up again at the first
speed after fifty minutes and keys F and C start to flash again for ten
minutes and so on.
By pressing any key for the exclusion of the hood light the hood will
return immediately to its normal functioning (e.g. if key D is pressed
the “clean air” function is deactivated and the motor moves to the 2nd
speed straight away. By pressing key B the function is deactivated).
(*) The “automatic stop timer” delays stopping of the hood, which
will continue functioning for 15 minutes at the operating speed set at the
time this function is activated.
• Active carbon/grease filter saturation: Fig.9A / Fig.10B
- When button A flashes at a frequency of 2 seconds, the grease filters
must be cleaned.
- When button A flashes at a frequency of 0.5 seconds, the carbon
filters must be replaced.
After the clean filter has been replaced, the electronic memory must
be reset by pressing button A for approximately 5 seconds, until the
light on the button stops flashing.
•COMMANDS:(Fig.9B)MECHANICAL_the key symbols are ex-
plained below:
A = LIGHT
B = OFF
C = SPEED I
D = SPEED II
E = SPEED III
G = MOTOR WORKING indicator
THE MANUF
A
CTURER DECLINES ALL RESPONSIBILITY FOR
EVENTUAL DAMAGES CAUSED BY BREACHING THE ABOVE
WARNINGS.
