Handleiding Etna 4489 rvs (pagina 4 van 19) (Nederlands, Duits, Engels, Frans)

130119

Verklein

Vergroot

Pagina terug

1/19

Pagina verder

- 4 -

and then carry out instructions for mounting filter version cooker hood.

• FILTERING VERSION

IInstall the cooker hood and the two connectors as described in the

paragraph mounting the exhausting version cooker hood.

To mount the filter connector refer to instructions included in the kit.

If the kit is not supplied, then order the kit as an accessory from your

local dealer. The filters must be fitted to the fan unit placed inside the

cooker hood. The air is replaced in the environment via the eyelets

impressed on the connector E.

USE AND MAINTENANCE

• It is recommended to operate the appliance prior to cooking.

It is recommended to leave the appliance in operation for 15 minutes

after cooking is terminated in order to completely eliminate cooking

vapours and odours.

The proper function of the cooker hood is conditioned by the regularity

of the maintenance operations, in particular, the active carbon filter.

• The anti-grease filters capture the grease particles suspended in the

air, and are therefore subject to clogging according to the frequency of

the use of the appliance.

In order to prevent fire hazard, it is recommendable to clean the filter

at a maximum of 2 months by carrying out the following instructions:

- Remove the filters from the cooker hood and wash them in a solution

of water and neutral liquid detergent, leaving to soak.

- Rinse thoroughly with warm water and leave to dry.

- The filters may also be washed in the dishwasher.

The aluminium panels may alter in colour after several washes. This

is not cause for customer complaint nor replacement of panels.

• The active carbon filters purify the air that is replaced in the

environment. The filters are not washable nor re-useable and must be

replaced at maximum every four months. The saturation of the active

carbon filter depends on the frequency of use of the appliance, by the

type of cooking and the regularity of cleaning the anti-grease filters.

• Clean the fan and other surfaces of the cooker hood regularly using

a cloth moistened with denatured alcohol or non abrasive liquid

detergent.

CONTROLS: 1A)ELECTRONIC 1B)LOGIC _(FIG.5)

A = LIGHT

B = OFF/SPEED I

C = SPEED II

D = SPEED III

E = AUTOMATIC STOP TIMER – 15 minutes

F = FILTER SATURATION RESET LIGHT

L = LOGIC

When the “filter saturation” light flashes, the anti-grease filters must

be washed.

When the light comes on without flashing, the anti-grease filters must

be washed and the carbon filters replaced (in case of operation whit the

recycling version).

When this operation has been completed, press the key to reset it.

The “automatic stop timer” delays stopping of the hood, which will

continue functioning for 15 minutes at the operating speed set at the

time this function is activated.

• LOGIC

a. AUTOMATIC LIGHT PLUS MOTOR OPERATION

Ensure that the cooker hood is in the OFF position and depress the

logic button. The motor starts up at the speed selection 1 and the lights

remain switched off. When the Logic function detects the presence of

a person or an increase in fumes and/or vapour, the lights turn on

automatically and the motor moves to speed selection 2. After 15

seconds the light switches off and the motor returns to the speed

selection 1. Depress the Logic button to disactivate the Logic function.

b. AUTOMATIC LIGHT OPERATION

Ensure that the the cooker hood is in the OFF position, depress the light

button and then the Logic button.

The lights switch on automatically when the Logic function detects the

presence of a person.

The light switches off after 15 seconds.

Depress the Logic button to disactivate the Logic function.

c. AUTOMATIC MOTOR OPERATION

Ensure that the the cooker hood is in the OFF position, depress the

motor start button on speed selection 1 or 2 and then the Logic button.

When the Logic function detects the presence of

a person or the increase of fumes and/or vapour

it will increase the motor speed automatically.

Depress the Logic button in order to disactivate the Logic function.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR

EVENTUAL DAMAGES CAUSED BY BREACHING THE ABOVE

WARNINGS.

ENGLISH

GENERAL

Carefully read the following important information regarding installation

safety and maintenance. Keep this information booklet accessible for

further consultations. The appliance has been designed as a exhausting

version (external exhaust) or as a filter version (internal air recycle)

cooker hood.

SAFETY PRECAUTION

1. Take care when the cooker hood is operating simultaneously with an

open fireplace or burner that depend on the air in the environment and

are supplied by other than electrical energy, as the cooker hood removes

the air from the environment which a burner or fireplace need for

combustion. The negative pressure in the environment must not exceed

4Pa (4x10 -5 bar). Provide adequate ventilation in the environment for

a safe operation of the cooker hood. Follow the local laws applicable

for external air evacuation.

2. WARNING !

In certain circumstances electrical appliances may be a danger

hazard.

A) Do not check the status of the filters while the cooker hood

is operating

B) Do not touch the light bulbs after appliance use

C) Flambè cooking is prohibited underneath the cooker hood

D) Avoid free flame, as it is damaging for the filters and a fire

hazard

E) Constantly check food frying to avoid that the overheated

oil may become a fire hazard

F) Disconnect the electrical plug prior to any maintenance.

G) This appliance is not intended for use by young children or

infirm persons without supervision

H) Young children should be supervised to ensure they do not

play with the appliance

I) There shall be adequate ventilation of the room when the

rangehood is used at the same time as appliances burning gas

or other fuels

L) There is a risk of fire if cleaning is not carried out in accordance

with the instructions

INSTALLATION INSTRUCTIONS

• ELECTRIC CONNECTION

The appliance has been manufactured as a class II, therefore no earth

cable is necessary.

The connection to the mains is carried out as follows:

BROWN = L line

BLUE = N neutral

If not provided, connect a plug for the electrical load indicated on the

description label. Where a plug is provided, the cooker hood must be

installed in order that the plug is easily accessible.

An omnipolar switch with a minimum aperture of 3mm between

contacts, in line with the electrical load and local standards, must be

placed between the appliance and the network in the case of direct

connection to the electrical network.

• The appliance must be installed at a minimum height of 650 mm from

an cooker stove in case of a gashob or an electrical hob.

If a connection tube composed of two parts is used, the upper part must

be placed outside the lower part.

Do not connect the cooker hood exhaust to the same conductor used

to circulate hot air or for evacuating fumes from other appliances

generated by other than an electrical source.

• Exhaust must not be discharged into a flue which is used for exhausting

fumes from an appliance burning gas or other fuels

• MOUNTING THE COOKER HOOD TO THE WALL

Drill holes A-B-C-D according to indications quoted in (fig. 3). Use

screws and screw anchors suitable for wall (e.g. reinforced cement,

plasterboard) for the mounting of the cooker hood. Where screws and

screw anchors are supplied ensure that they are suitable for the type

of wall where the cooker hood is to be mounted. Lock in the flange

connector Y to the cooker hood (fig. 2). Affix the bracket Z to the wall

via the drill holes A (fig. 4). Hang the cooker hood on the wall using the

drill holes C (fig. 3). Fasten the cooker hood using the fastening drill

holes D (fig. 3).

• EXHAUSTING VERSION

Connect the flange Y to the discharge opening with a connecting tube

(do not carry out for filter version). Thread the upper connector E to the

inside of the lower connector F; hang the two connectors inserting

them vertically on the cooker hood locking the lower connector F to the

wall using the drill holes B (fig. 3), unthread the upper connector E

towards the top, locking it in with the appropriate screws in the drill

holes G of the bracket Z (fig. 2) previously affixed to the wall via the drill

holes A (fig. 3). In order to transform your cooker hood from exhausting

version to filter version, ask your local retailer for active carbon filters

Etna 4489 rvs Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info