1.Remove the contents from the box. Remove all packing tape
and packing material from outside and inside the printer. Be
sure not to touch the ribbon cable inside the printer.
2.Open the paper support, then slide out the extension and plug
in the printer.
3 Installing the Ink Cartridges
Installing the Ink Cartridges Installing the Ink Cartridges
Installing the Ink Cartridges
1.Press the Ppower button to turn on the printer.
cCaution:
Make sure that the CD/DVD guide is closed when turning on the printer.
2.Remove the ink cartridges from their protective bags, then install the ink cartridges as shown below.
cCaution:
❏Do not shake the ink cartridges; this can cause leakage.
❏Be careful not to break the hook on the side of the ink cartridge when you remove it from the protective bag.
❏Do not remove or tear the label on the cartridge; this can cause leakage.
❏Do not move the print head by hand; otherwise, you may damage the printer.
❏Push the ink cartridge down until it clicks into place.
❏Do not load paper until ink charging is complete.
Note:
Install all ink cartridges. The printer will not work unless all cartridges are installed properly.
3.Press the Hink button.
The printer begins ink charging. It takes about one and a half minutes. While charging, the printer produces a variety of mechanical sounds. This is normal.
When the green light stops flashing, ink charging is complete.
cCaution:
Do not turn off the printer during the ink charging process.
Note:
The ink cartridges packaged with your printer are partly used during initial setup. In order to produce high quality printouts, the print head in your printer
will be fully charged with ink. This one-off process consumes a quantity of ink and subsequent cartridge sets will last for their full rated life.
The contents may vary in certain locations.
The power cord comes attached in some countries.
Setup
printer
ink cartridges
CD/DVD traypower cordCD-ROM8cm CD/DVD
attachment
CD-R print
position
check sheet
Do not touch
this part.
Do not remove
the tape seal.
Installing the Printer Software
Installing the Printer Software Installing the Printer Software
Installing the Printer Software
1.Press the Ppower button to turn off the
printer. The green light goes off.
2.Connect the printer and computer with a USB cable, then
insert the printer software CD into the CD-ROM drive.
3.Install the printer software.
Select your country or area of residence if the selection window
appears. Then except where otherwise instructed, click or double-click
the areas circled in red to proceed.
cCaution:
Turn off all virus protection programs before installing the printer
software.
Note:
If the language selection window appears, select your preferred
language.
For Windows
For WindowsFor Windows
For Windows
For Mac OS 8.6 to 9.X
For Mac OS 8.6 to 9.XFor Mac OS 8.6 to 9.X
For Mac OS 8.6 to 9.X
For Mac OS X
For Mac OS XFor Mac OS X
For Mac OS X
Note:
❏This software does not support the UNIX File System (UFS) for Mac OS
X. Install the software on a disk or in a partition that does not use UFS.
❏This product does not support the Mac OS X Classic environment.
1.Open the Mac OS X folder, then double-click the EPSON icon.
If the Authorization dialog box appears, (for Mac OS 10.1.x, click
the icon,) enter the Password or phrase, then click OK.
2.Follow the on-screen instructions to install the software.
3.After installing the software and restarting the computer, press the
P button to turn on the printer.
4.Open the Applications folder on your hard drive, then open the
Utilities folder and double-click the Print Center icon. Click
Add icon (for Mac OS 10.1.x, click AddPrinter) in the Printer List
dialog box.
5.Select EPSON USB from the pop-up menu. Select Stylus Photo
R200 in the Product list, then select All from the Page Setup pop-up
menu. Click Add.
6.Make sure the Printer List contains the
printer(margin-type) options as
illustrated below. See the Reference
Guide for more details.
7.Close Printer List dialog box.
Note:
When you print, be sure to match the Format for setting in the Page
Setup dialog box and the Printer setting in the Print dialog box.
Otherwise, the data may not be printed correctly. See the
Reference Guide for more details.
After installation is complete, see the Reference Guide for
detailed information about printing from your computer for
the first time.
The CD-ROM includes EPSON Print CD, EPSON PhotoQuicker, EPSON
PhotoStarter, EPSON CardMonitor, EPSON PRINT Image Framer Tool, and
PIF DESIGNER.
You can print on CD/DVDs to make your own original CD/DVDs using
EPSON Print CD which is included with this printer. For more details,
double-click the ESPR200 Reference Guide icon on the desktop.
EPSON PhotoQuicker is a fun and easy to use program with a number of
features that help you create outstanding photos. It also allows you to
create borderless photos.
For more details, double-click the ESPR200 Software Guide icon on the
desktop to view Photo Print Software Setup.
Viewing the Reference Guide
Viewing the Reference Guide Viewing the Reference Guide
Viewing the Reference Guide
The Reference Guide provides detailed information about printing from a computer, printer maintenance, problem solving, and safety.
To view the Reference Guide, double-click the ESPR200 Reference Guide icon on the desktop.
In Windows, you can also access the Reference Guide via the Start menu. To do so, click Start, point to All Programs in Windows XP or Programs in Windows
Me, 98, or 2000, point to EPSON, then select ESPR200 Reference Guide.
Safety Instructions
Read all of the instructions in this section when setting up and using your printer.
When choosing a place for the printer
❏Avoid places subject to rapid changes in temperature and humidity. Also, keep the printer away from direct
sunlight, strong light, or heat sources.
❏Avoid places subject to dust, shocks, or vibrations.
❏Leave enough room around the printer to allow for sufficient ventilation.
❏Place the printer near a wall outlet where the plug can be easily unplugged.
❏Place the printer on a flat, stable surface that extends beyond the base of the printer in all directions. If you
place the printer by the wall, leave more than 10 cm between the back of the printer and the wall. The printer
will not operate properly if it is tilted at an angle.
❏When storing or transporting the printer, do not tilt it, stand it on its side, or turn it upside down. Otherwise ink
may leak from the cartridge.
When choosing a power source
❏Use only the type of power source indicated on the printer’s label.
❏Use only the power cord that comes with this product. Use of another cord may result in fire or electric shock.
❏This product’s power cord is for use with this product only. Use with other equipment may result in fire or electric
shock.
❏Be sure your AC power cord meets the relevant local safety standard.
❏Do not use a damaged or frayed power cord.
❏If you use an extension cord with the printer, make sure that the total ampere rating of the devices plugged
into the extension cord does not exceed the cord’s ampere rating. Also, make sure that the total ampere rating
of all devices plugged into the wall outlet does not exceed the wall outlet’s ampere rating.
❏If you plan to use the printer in Germany, the building installation must be protected by a 10 or 16 amp circuit
breaker to provide adequate short-circuit protection and over-current protection for this printer.
When handling ink cartridges
❏Keep ink cartridges out of the reach of children. Do not allow children to drink from or otherwise handle the
cartridges.
❏Do not open the ink cartridge packages until just before you install them.
❏Be careful not to break the hooks on the side of the ink cartridge when you remove it from the package.
❏Be careful when you handle used ink cartridges, as there may be some ink remaining around the ink supply
port. If ink gets on your skin, wash the area thoroughly with soap and water. If ink gets into your eyes, flush them
immediately with water. If discomfort or vision problems remain after a thorough flushing, see a doctor
immediately.
❏Do not shake the ink cartridges; this can cause leakage.
❏Do not remove or tear the label on the cartridge; this can cause leakage.
❏Do not touch the green IC chip on the side of the cartridge.
❏The IC chip on this ink cartridge retains a variety of cartridge related-information, such as the amount of ink
remaining, so that a cartridge may be removed and reinserted freely. However, each time the cartridge is
inserted, some ink is consumed because the printer automatically performs a reliability check.
When using the printer
❏Do not put your hand inside the printer or touch the ink cartridges during printing.
❏Do not block or cover the vents and the openings in the printer.
❏Do not attempt to service the printer yourself.
❏Unplug the printer and refer servicing to qualified service personnel under the following conditions:
The power cord or plug is damaged; liquid has entered the printer; the printer has been dropped or the casing
damaged; the printer does not operate normally or exhibits a distinct change in performance.
❏Do not insert objects through the slots in the printer.
❏Take care not to spill liquid on the printer.
❏Leave the ink cartridges installed. Removing the cartridges can dehydrate the print head and may prevent the
printer from printing.
Information for United Kingdom Users
Use of options
EPSON (UK) Limited shall not be liable against any damages or problems arising from the use of any options or
consumable products other than those designated as Original EPSON Products or EPSON Approved Products by
EPSON (UK) Limited.
Safety information
wWarning:
Refer to the rating plate for the voltage and check that the appliance voltage corresponds to the supply
voltage.
Important:The wires in the mains lead fitted to this appliance are coloured in accordance with the following
code:
Blue — Neutral
Brown — Live
If you have to fit a plug:
As the colours of the mains lead of this appliance may not match the coloured markings used to identify the terminals
in a plug, please observe the following:
❏The blue wire must be connected to the terminal in the plug marked with the letter N.
❏The brown wire must be connected to the terminal in the plug marked with the letter L.
❏If the plug is damaged, replace the cord set or consult a qualified electrician.
❏Replace fuses only with fuses of the correct size and rating.
Follow the on-screen instructions.
12
Follow the on-screen instructions.
After installing the software and restarting
the computer, turn on the printer.
Setup
Color Ink Jet Printer
English
4046840-00
xxx
cCautions must be observed to avoid
damage to your equipment.
Notes contain important information and
useful tips on the operation of your printer.
Warnings, Cautions and Notes
wWarnings must be followed carefully to
avoid bodily injury.
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission
of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson printer. Epson is not responsible for any use of this information as applied to other printers. Neither Seiko Epson Corporation nor its affiliates
shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs,
or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions.
Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko
Epson Corporation. Seiko Epson Corporation shall not be held liable for any damage resulting from electromagnetic interference that occurs from the use of any interface cables other than those designated as Epson Approved Products
by Seiko Epson Corporation. EPSON® is a registered trademark and Epson Stylus™ is a trademark of Seiko Epson Corporation.
Microsoft® and Windows® are registered trademarks of Microsoft Corporation.
Apple® and Macintosh® are registered trademarks of Apple Computer, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
Hulp nodig? Stel uw vraag in het forum
Misbruik melden
Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.
Product:
Spelregels forum
Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:
lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;
Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.
Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.
Abonneren
Abonneer u voor het ontvangen van emails voor uw Epson Stylus Photo R200 bij:
nieuwe vragen en antwoorden
nieuwe handleidingen
U ontvangt een email met instructies om u voor één of beide opties in te schrijven.
Ontvang uw handleiding per email
Vul uw emailadres in en ontvang de handleiding van Epson Stylus Photo R200 in de taal/talen: Engels als bijlage per email.
De handleiding is 0,64 mb groot.
U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.
Stel vragen via chat aan uw handleiding
Stel uw vraag over deze PDF
Andere handleiding(en) van Epson Stylus Photo R200
Uw handleiding is per email verstuurd. Controleer uw email
Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.
Er is een email naar u verstuurd om uw inschrijving definitief te maken.
Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken
U heeft geen emailadres opgegeven
Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.
Uw vraag is op deze pagina toegevoegd
Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.
