Base Station
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
15.214 (d) Cordless telephones shall incorporate circuitry which makes use of a
digital security code to provide protection against unintentional access to the public
switched telephone network by the base unit and unintentional ringing by the
handset. These functions shall operate such that each access of the telephone
network or ringing of the handset is preceded by the transmission of a code word.
Access to the telephone network shall occur only if the code transmitted by the
handset matches the code set in the base unit. Similarly, ringing of the handset shall
occur only if the code transmitted by the base unit matches the code set in the
handset. The security code required by this Section may also be employed to
perform other communications functions, such as providing telephone billing
information. This security code system is to operate in accordance with the
following provisions.
(1) There must be provision for at least 256 possible discrete digital codes. Factory-
set codes must be continuously varied over at least 256 possible codes as each
telephone is manufactured. The codes may be varied either randomly, sequentially,
or using another systematic procedure.
(2) Manufacturers must use one of the following approaches for facilitating
variation in the geographic distribution of individual security codes:
(i) Provide a means for the user to readily select from among at least 256 possible
discrete digital codes. The cordless telephone shall be either in a non-operable
mode after manufacture until the user selects a security code or the manufacturer
must continuously vary the initial security code as each telephone is produced.
(ii) Provide a fixed code that is continuously varied among at least 256 discrete
digital codes as each telephone is manufactured.
(iii) Provide a means for the cordless telephone to automatically select a different
code from among at least 256 possible discrete digital codes each time it is
activated.
(iv) It is permissible to provide combinations of fixed, automatic, and user-
selectable coding provided the above criteria are met.
(3) A statement of the means and procedures used to achieve the required
protection shall be provided in any application for equipment authorization of a
cordless telephone.
Industry Canada Statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired
operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux
appareils radio exempts de licence. Son fonctionnement est sujet aux deux
conditions suivantes: (1) le dispositif ne doit pas produire de brouillage
préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un
brouillage susceptible de provoquer un fonctionnement indésirable.
IMPORTANT NOTE:
