ENDURO
®
EM305
+
35
Ref: EM305P-UM-TKI-0119-Rev.A.
The slide switch (Fig. 5A) also acts as an “Emergency stop”.
The automatic engaging system:
To activate the automatic engaging system of the motor powered rollers on the tyre, press the two buttons for
engaging (Fig. 5I) or disengaging (Fig. 5J) for at least three seconds. The blue LED (Fig. 5K) will blink fast
during these three seconds and every second there will be a beep. This warns you that the system will be
activated!
Engaging: After these three seconds the motor powered rollers will be pressed against the tyre, and the blue
LED will illuminate constant. Now you can release the two buttons. When the motor powered rollers are pressed
on the tyre strongly enough you hear a short beep, the blue LED will switch off and the system is ready to use.
Disengaging: after these three seconds the motor powered rollers will be released from the tyre, and the blue
LED will illuminate constant. Now you can release the two buttons. When the motor powered rollers are
completely disengaged you hear a short beep, the blue LED will switch off and is the system ready for
transport.
The remote hand set switches off:
After 3 minutes, if no button is pressed: After 2 minutes the buzzer will beep for 5 times with a repetition
after 3 minutes. Than the system switches in the “stand-by” modes.
After 6 minutes, if one of the movement buttons is permanently held down: After 5 minutes the buzzer will
beep for 5 times with a repetition after 6 minutes. Than the system switches in the “stand-by” modes.
The green LED goes off and the remote handset is in the “stand-by” modes which means that there always will
be used some current which causes the battery to go down. So always make sure the remote handset is turned
off by the slide switch.
To reactivate the remote handset, move slide switch to “Off” –O and then back to “On”-I after approximately 1
second.
Error messages via the remote handset:
Error messages of the ENDURO
®
EM305
+
will be communicated via the remote handset by the green LED (Fig.
5H), the error message LED’s (Fig. 5L, 5M & 5N) and a buzzer signal:
Green LED (Fig. 5H) off, no buzzer: remote handset is turned off and also system is not activated
Green LED (Fig. 5H) continue on, no buzzer: remote handset is turned on and system is activated and
ready to use.
Green LED (Fig. 5H) is blinking, no buzzer: no communication between handset and control unit. This could
be because of too much distance between remote handset and control unit, or the battery isolation switch
for manoeuvring system is not turned on or that there is a distortion signal disturbing the communication.
As soon as connection is good again the green LED will be continue on and the system is ready to use.
Blue battery voltage LED (Fig. 5N) is blinking in combination with buzzer (2 times blinking, break, 2 times
blinking, break etc.): Battery voltage too low (<10 Volt). Battery needs to be recharged.
Blue battery voltage LED (Fig. 5N) is blinking in combination with buzzer (4 times blinking, break, 4 times
blinking, break etc.): Battery Voltage too high (over charged). Try to discharge the battery by turning on a
user (for example a lamp or water-pump).
Red overload LED (Fig. 5L) is blinking in combination with buzzer (6 times blinking, break, 6 times blinking,
break etc.): Amp overload protection is activated. Wait about 60 seconds and try again.
Blue 9 Volt battery LED (Fig. 5M) is blinking, no buzzer: The internal 9 Volt battery is near empty and
needs to be replaced.
Changing batteries in the remote handset:
When the battery is empty (blue 9 Volt battery LED (Fig. 5M) is blinking), it needs to be replaced.
Open the rear cover of the handset (Fig. 7A).
Take out the dead/old battery and dispose in the appropriate way.
Install a new replacement battery (Fig. 7.1). Make sure to use a leak proof PP3 (9 Volt) battery (No claims
under guarantee can be considered for damage caused by leaking batteries).
Close the rear cover again.
Dead and used batteries may leak and damage the remote handset! Remove the batteries if the handset is not
going to be used for an extended period.
