The supplied double mode remote handset (5) can be used for the ENDURO® autoSteady system and most
ENDURO® caravan manoeuvring systems (models >2013). The control mode can be selected by moving the slide
switch (Fig. 8O) to “Caravan manoeuvring system mode” or “autoSteady system mode”.
The remote handset is powered by one PP3 9Volt battery, and is activated by moving the slide switch to “On”-I
(Fig. 8A). Once activated the green LED (Fig. 8H) will illuminate and the controls can now be used.
Fig. 8 (autoSteady mode):
A. Main power slide switch: “Off”=O and “On”=I.
B. Up button in individual mode: Select the draw-back function for single corner steady function buttons.
After this button is pressed, the red LED above this button will light up. Then you can push the single
corner steady function buttons for draw back. Without this selection the single corner steady function
buttons are not workable. If there is not any operation within 30 seconds, the LED will turn off and
invalidate the “UP” choice.
C. Down button in individual mode: Select the lower function for single corner steady function buttons.
After pressing this button, the red LED below this button will light up. Then you can push the single corner
steady function buttons for lower. Without this selection the single corner steady function buttons are not
workable. If there is not any operation within 30 seconds, the LED will turn off and invalidate “Down”
choice.
D. Right-front single corner steady function button: Adjust Right-front corner steady (see Fig. 7) draw
back or lower by keep pushing the button. Choose the “UP” or “DOWN” button first.
E. Left-front single corner steady function button: Adjust Left-front corner steady (see Fig. 7) draw back
or lower by pressing the button. Choose the “UP” or “DOWN” button first.
F. Right-back single corner steady function button: Adjust Right-back corner steady (see Fig. 7) draw
back or lower by keep pushing the button. Choose the “UP” or “DOWN” button first.
G. Left-back single corner steady function button: Adjust Left-back corner steady (see Fig. 7) draw back
or lower by pressing the button. Choose the “UP” or “DOWN” button first.
H. Green power LED: Power LED continuously lights up when the system is activated (by moving slide
switch of the remote handset to “On”-I). If the remote handset is far away from the control unit, beyond
the availably distance, this LED will start blinking.
I. Two handed buttons for automatic up function: The “AUTO UP” button must be pressed for more than
3 seconds. The blue “automatic function” LED will blink and the buzzer also gives a beep per second. Then
the automatic draw back process begins. If press it for less than 3 seconds, nothing happens (this is a
setup to avoid misoperation). After three seconds the automatic lower or draw back begins, and the blue
“automatic function” LED will illuminate constantly. Now you can release the button, and the draw back
process will auto process. After the automatic draw back process is completed, the buzzer will give a beep.
J. Two handed buttons for automatic down function: The “AUTO DOWN” button must be pressed for
more than 3 seconds. The “automatic function” LED will blink and the buzzer also gives a beep per second.
Then the automatic lower process begins. If press it for less than 3 seconds, nothing happens (this is a
setup to avoid misoperation). After three seconds the automatic lower process begins, and the “automatic
function” LED will illuminate constantly. Now you can release the button, and the lower process will auto
process. After the automatic lower process is completed, the buzzer will give a beep. Before the corner
steadies move downwards, there maybe a several second delay without any operation or the corner steady
draw back a short time (about 3 seconds). This is normal.
K. Blue “automatic function” LED: Reflects status of the “AUTO UP” and “AUTO DOWN” system.
L. Red overload LED: Amp overload protection is activated. Wait about 60 seconds and try again.
M. Blue 9V battery LED: The internal 9V battery of handset is near empty and needs to be replaced.
N. Blue battery voltage LED: The caravan battery voltage is too low or too high.
O. Control mode slide switch: The control mode can be selected by moving the slide switch (Fig. 8O) to “P”
or “Q”. If moving the slide switch (Fig. 8O) to “P” (indication becomes red), the combined remote handset
is working in the caravan manoeuvring system mode. If moving the slide switch (Fig. 8O) to “Q” (indication
becomes red), the combined remote handset is working in the autoSteady mode.
P. Caravan manoeuvring system mode indicator: Reflects status of remote handset. When the remote
handset is set into the caravan manoeuvring system modes, an ENDURO® caravan manoeuvring system can
be controlled via this remote handset. Please see functions of the buttons in the caravan manoeuvring
system user manual. NOTE: in this mode the autoSteady system will not work!
Q. autoSteady control mode indicator: Reflects status of remote handset. When the remote handset is set
into the autoSteady system modes, the autoSteady system can be controlled via this remote handset.
NOTE: in this mode the caravan manoeuvring system will not work!
R. Red LED: reflects status of “UP” function in the individual mode.
S. Red LED: reflects status of “DOWN” function in the individual mode.
For the button functions in the caravan manoeuvring system mode, please check the user manual of your
ENDURO® caravan manoeuvring system.
The slide switch (Fig. 8A) also acts as an “Emergency stop”.
