722072
42
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
ENDURO
®
autoSteady 35
Ref: AS101-UM-TKI-0114-Rev. A
R - Red LED: reflects status of “UP” function in the individual mode.
S - Red LED: reflects status of “DOWN” function in the individual mode.
For the button functions in de Caravan manoeuvring system mode, please check the user manual of your
EN
DURO
®
caravan manoeuvring system.
The slide switch (Fig. 10A) also acts as an Emergency stop.
The remote control handset switches off:
After 3 minutes, if no button is pressed: After 2 minutes the buzzer will beep for 5 times with a repetition
after 3 minutes. Than the system switches in the “stand-by” modes.
After 6 minutes, if one of the movement buttons is permanently held down: After 5 minutes the buzzer will
beep for 5 times with a repetition after 6 minutes. Than the system switches in the “stand-by” modes.
The green LED goes off and the remote control handset is in the “stand-by” modes which means that there
always will be used some current which causes the battery to go down. So always make sure the remote
control handset is turned off by the slide switch.
To reactivate the remote control, move slide switch to “Off” –O and then back to “On”-I after approximately 1
second.
Error messages via the remote control handset:
Error messages of the autoSteady system will be communicated via the remote control handset by the green
LED (Fig. 10H), the error message LED’s (Fig. 10L, 10M & 10N) and a buzzer signal:
Green LED (Fig. 10H) off, no buzzer: remote control handset is turned off and also system is not activated
Green LED (Fig. 10H) continue on, no buzzer: remote control handset is turned on and system is activated
and ready to use.
Green LED (Fig. 10H) is blinking, no buzzer: no communication between handset and control unit. This
could be because of too much distance between remote control handset and control unit, or the battery
isolation switch for manoeuvring system is not turned on or that there is a distortion signal disturbing the
communication. As soon as connection is good again the green LED will be continue on and the system is
ready to use.
Blue battery voltage LED (Fig. 10N) is blinking in combination with buzzer (2 times blinking, break, 2 times
blinking, break etc.): Battery voltage too low (<10V). Battery needs to be recharged.
Blue battery voltage LED (Fig. 10N) is blinking in combination with buzzer (4 times blinking, break, 4 times
blinking, break etc.): Battery Voltage too high (over charged). Try to discharge the battery by turning on a
user (for example a lamp or water-pump).
Red overload LED (Fig. 10L) is blinking in combination with buzzer (6 times blinking, break, 6 times
blinking, break etc.): Amp overload protection is activated. Wait about 60 seconds and try again.
Blue 9V battery LED (Fig. 10M) is blinking, no buzzer: The internal 9V battery is near empty and needs to
be replaced.
Changing batteries in the remote control handset:
When the internal battery is empty (blue LED (Fig. 10M) is blinking 2Hz), it needs to be replaced.
Open the rear cover of the remote control (Fig. 11A).
Take out the old battery and dispose in the appropriate way.
Install a new replacement battery (Fig. 12). Make sure to use a leak proof PP3 (9Volt) battery (No claims
under guarantee can be considered for damage caused by leaking batteries).
Close the rear cover again.
Dead and used batteries may leak and damage the remote control! Remove the batteries if the remote control
is not going to be used for an extended period.
How to synchronise the remote handset with a new manoeuvring system or autoSteady control unit:
The remote control handset and the autoSteady control unit are synchronised with each other in the factory. If
the control unit or the remote control handset is replaced, or the combine-remote handset will also be used for
an EN
DURO
®
caravan manoeuvring system, they must be re-synchronised as described below:
Check the installation in accordance with the installation instructions. Check that the battery is properly
connected, check the condition of the battery and that a voltage of 12V is present at the control unit.
Please ensure that the battery isolation switch is on.
Press the reset button on the control unit:
o autoSteady system
: Press the reset button (Fig. 13D) on the autoSteady control unit for three
seconds and then release it. The green LED (Fig. 13A) starts blinking quickly (2Hz).
o EN
DURO
®
caravan manoeuvring system: Press the reset button (see user manual caravan
manoeuvring system) on the EN
DURO
®
caravan manoeuvring system control unit for three seconds
and then release it. The green LED on the control unit starts blinking quickly (2Hz).
Activate the remote control by sliding the slide switch (Fig. 10A) to “On”-I. The green LED of the remote
control and the “UP” and “DOWN” LED’s (Fig. 10R & 10S) will illuminate continuously.
Push both the “UP” and “DOWN” buttons (Fig. 10B & 10C) on the remote control at the same time for more
than 3 seconds. Then the handset buzzer will give a short beep to confirm that the synchronisation is
complete.
After successful synchronisation, the green LED on the control unit (Fig. 13A) and on the remote control
(Fig. 10H) will illuminate continuously.
42

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Enduro AS101 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Enduro AS101 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 5,72 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info