708667

Elro AP5500 - Pro Alarm System Handleiding

5
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
ELRO 10 Zone Pro Alarm
System
with Voice and Digital
Dialer
AP5500
Position - planning
Congratulations with your new ELRO PRO Alarm System AP5500, a secure and independently
working Alarm System!
This Short manual will help you through installation and Set-Up of your System effectively. If you have
further questions, ideas or recommendations, visit www.elro.eu
for a detailed manual, an FAQ section
and the possibility to leave us with your honest feedback on our products.
MULTIPLE USERS
The system allows up to 6 Users and one Master User. Each user will have a different Password.
Agree about the different Passwords:
Master:______User1:______User2:______User3:______User4:______User5:_______User6:______
How to start?:
Overview your home as a burglar! Which entrances do you think he will take? What is your main
entrance? Do you want to switch your alarm on and off with a remote, use the Alarm Panel, or use an
external Keypad (not included). What do you need to prevent and how? Do you want to switch on the
alarm only when you are away from home, or also when you are a sleep?
A: Door/window contact B: PIR motion sensor C: PIR motion sensor E: Remote Control
D: Door/window contact F: Alarm Panel
Divide the house in Alarm parts according figure:
It is possible to put the Alarm system in Partial armed (2 different parts) and full armed.
For example when we are at home we only Arm the Garage PARM1, but not the rest. If we are a sleep, we
only arm the Garage and down floors PARM2, but not the rest. If we are away from home Full armed.
We also can give a sensor being defined as an sensor with Exit/Entry Delay. For example; If we leave
home, and we want to switch on the alarm on the panel, we give the door/window magnet E: the Exit/Entry
delay status. All other sensors can have the immediate status. Your system can be divided in groups or
zones. When there is an alarm you can see which Zone gave alarm. The zone number also will be selected
on the sensor. All sensor in the same zone will have the same PARM and Exit/Entry delay statuses.
You can divide up to 6 zones. If you have not more than 6 zones you can give each sensor its own zone
number.
Draw a map of your home, mark the places to be secured, and make an overview on the last page like:
A: Door/window contact : Zone number: 01 PARM1:On PARM2: On Exit/Entry Delay: Off
B: PIR Motion Sensor : Zone number: 02 PARM1:Off PARM2: On Exit/Entry Delay: Off
C: PIR Motion Sensor : Zone number: 03 PARM1:Off PARM2: Off Exit/Entry Delay: Off
D: Door/window contact : Zone number: 04 PARM1:Off PARM2: On Exit/Entry Delay: On
E: Remote Control : advise to take this with you when you go to bed. Easy to control the alarm, and in
reach in case of panic!
F: Alarm Panel : can be installed hidden, for example behind the hood in the hall.
Telephone numbers: Consider which numbers must be called in case of alarm: fill in the numbers on the
overview on the last page.
5
1 32
4
ON
7
6 8
ECE
Hole
Jack Socket
Terminal Block
Switch Jumper
Upper Keyhold
Fixing Hole
+ve Terminal
(Red Lead)
Link P51
External Tamper
Lower Fixing
(Blue Lead)
-ve Terminal
Link P1
Power Supply
Reset Jumper
+ve Terminal
(Blue Lead)
(Black Lead)
-ve Terminal
Fixing Hole
Upper Keyhole
Preparing and installing our new ELRO 10 Zone alarm system.
We advise to do the pre work, easily on the table, and install later. First unpack all accessories and
sort the batteries together with the accessories. Unscrew and open all products.
House Code:
All products must be programmed with the same house code. In all accessories (not in the Alarm
panel) you will find a code dipswitch block like in figure:
The Alarm Panel:
LCD Display Window
Keypad Status LEDs
Connect battery leads to both back-up batteries: Battery 1 (left): Red lead to +, Blue lead to –, Battery 2
(right): Blue lead to +, Black lead to –ve battery terminal.
If the telephone based functionality is to be used then the Control Panel will need connecting to a
convenient telephone point. Route the cable from the Power Supply Unit up behind, connect the plug to
the DC power socket in the panel. Take care that during installation and testing on the table, the
sabotage switch and the back stays free. Now set the Alarm panel in programming mode, by pressing:
‘1 USER SETUP’ is displayed.
Remote Control:
The Remote Control is used to Arm, Part-Arm 1-2 and Disarm the system, or give a panic alarm.
Insert the 3V (CR2032) battery.
Check if you entered the wished
house code into the remote, same
as in the magnet and the PIR.
We start learning the code to the
Alarm Panel
Use the and buttons to scroll through the menu until ‘2. SYSTEM SETUP’ is displayed.
Press and ‘2-1 Learn House Code’ will be displayed. Press again to set the Control Panel to
receive the House code, press the on the remote control: house code will be displayed in figures.
Testing the Alarm Panel by the Remote Control:
Press: to put the system in the TEST mode.
Create your own personal code, by putting some switches to on,
or off. Be sure that you use the same code in all accessories.
Indicator
PCB Position
PCB Board
Dip Switches
‘TEST MODE – WALK TEST’ is displayed.
Press to activate Walk Test. ‘ Walk Test Waiting…’ is displayed. Press the ‘ARM’ button
on the Remote Control; Alarm Panel will beep and the type of the device and button will be on the
display. Press the other buttons on the Remote, as each button is pressed the Alarm Panel will beep
and show the button being pressed on the display. KEEP THE ALARM PANEL IN THE TEST MODE!
PIR Motion Sensor:
PIR Sensors are designed to detect movement.
Insert the 9 Volt battery. The PIR will warm-up during 2-3 minutes. The LED will flash. When it is ready
the LED stops. First check the house code: SW2; switch 1 – 8 (must be same as Remote Control). You
can divide your detectors over your total home in zones. You can set the alarm zone the PIR detector
will operate on, by switch the dip switches 1, 2 and 3 (of SW3; dipswitch 1-5) in the position according
schedule above. Mark which zone number on the PIR. For walk test mode you put dip 4 of SW3 On.
Don’t forget to put back in Off. Test the PIR in the walk test mode. In normal mode the PIR will only send
a mew signal after being triggered after 2 minutes
The PIR sensor incorporates an anti-false alarm for where the Sensor might be affected by e.g. insects,
air temperature etc. We recommend high sensitivity, but in case of affection of (e.c. insects) , you can
adjust dip 5 of SW3 to Off: low sensitivity detection!
Door/window magnet:
The Magnetic Contact consists of two parts; a Detector and a Magnet. They are designed to be fitted
to doors or windows with the Magnet mounted on the moving/opening part.
Mounting the door/wind magnet:
Decide which doors/windows are to be protected by fitting Magnetic
Contact Detectors, (usually the front and back doors. Additional detectors
may also be fitted where required to other vulnerable doors or windows,
(e.g. garage, patio/conservatory doors etc).Ensure that the position selected
for the Magnetic Contact detector is within effective range of the Control Panel, (refer to
‘Testing the Control Panel & Remote Control’). Remove the battery holder, and mount the
detector using either the adhesive tape or screws. Fit the Magnet to the moving part of the door/window
opposite the Detector. Ensure that the parallel gap between the Magnet and Detector is less than 10mm
and that the arrow on the Magnet is pointing towards and aligned with the mark on the Detector.
Mounting the PIR motion sensor:
Household pets should not be allowed into an area protected by a PIR detector! Do not locate the
detector facing a window facing direct sunlight. PIR Detectors are not suitable for use in
conservatories. Do not locate the detector where it is exposed to ventilators. Do not locate the detector
DIP 1 DIP 2 DIP 3
Zone 1 OFF OFF OFF
Zone 2 OFF OFF ON
Zone 3 OFF ON OFF
Zone 4 OFF ON ON
Zone 5 ON OFF OFF
Zone 6 ON OFF ON
E
1 2 3
Open the sensor, take out the battery
connector, and place the battery! Check the
house code; same as PIR and Remote Dip 1-
8 from 1-12. Select the Zone you want: setting
Dip 9-11 according the overview at the PIR.
Mark the Zone number on the magnet.
directly above a heat source, (e.g. fire, radiator, boiler, etc). Where possible, mount the detector in the
corner of the room so that the logical path of an intruder would cut across the fan detection pattern.
PIR detectors respond more effectively to movement across the device than to movement directly
towards it. Where possible, mount the detector in the corner of the room so that the logical path of an
intruder would cut across the fan detection pattern.
A
Less Sensitive More Sensitive A 1=6, 2=9,3=12m
Carefully drill out the required mounting holes in the rear cover; A. Using the rear cover as a template,
mark the positions of the fixing holes on the wall. Fix the rear cover to the wall. Detection area is
adjustable up to 12 meter; you can move the PCB up or down. Check again if Dip 4 of SW3(dipswitch
1-5) in Off. In test mode the PIR will send after every trigger a signal. In the regular mode the PIR will
pause 2 minutes, and then send again a signal after being triggered, to save batteries.
Programming the Alarm Panel:
We advise to do the programming before mounting the Alarm Panel. First we change from the Walk Test
mode to the Program/Install mode. Press until you see in the display: ‘DISARM READY” and the
time! Now we go into the Program/Install mode; mentioned further Inst. mode:
Press , 1 2 3 4 (1 2 3 4 standard Master Password), display show 1.USER SETUP.
First we will change the Master Password! Press : 1-1 USER 1 SETUP. Press
display: 1-7 MASTER SETUP, Press , display: :1 Password 1234 , Press , display:
Enter Password Code: NOW PRESS YOUR NEW CODE! and , display: :1 Password ???? .
Check if ???? is the password you entered. If ok, press 2x ,display: 1. USER SETUP, Press
display: 1-1 USER 1 SETUP, Press , display: :1 Password. Press , display: Enter
Password Code: NOW PRESS THE CODE FOR USER 1 and , display : will show the
Password you entered, CHECK! After the password
Next step is that we define some standard settings, per sensor ; press until you see in the
display:
1. USER SETUP. Press ,until in display: 3. ZONE SETTING. No we can choose:
Zone Setup (Z1-10) ; fill in the Zone Number you defined in the sensors!
Select all the zones you defined in the sensors!
Name
No Name
You can select a room name, or leave ‘no name’
Type
Intruder
Normal sensor will be ‘intruder’.
Final Exit
OFF
‘OFF’
Chime
OFF
‘OFF’
Entry Delay Zone 1
Zone 2-10
ON, 30s
OFF
Depends if you have to pass the
when you leave, or come back!
Part-Arm 1
OFF
Do you want switch this sensor on in PARM1
Part-Arm 2
OFF
Do you want switch this sensor on in PARM2
Walk Through
OFF
‘OFF’
Next step is that we define some standard system settings: ; press until you see in the display:
3. ZONE SETTING. Press , display 2. SYSTEM SETTING. Choose:
System Setup
House Code
01010101
This is the house code you programmed on page 2
Alarm Time
ON, 180s
Loud alarm is ON. No sound from Alarm Panel ; Off
Wirefree Siren
ON
‘ON’
RF Jamming Detection
OFF
‘OFF’
Back Light
10s
Backlight of display switches of ….. seconds
Alarm Relay
On Until Disarm
‘ON’
Zone Lockout
ON
‘ON’
Remote Phone Control
ON
‘ON’
Rings to Answer Phone
6
‘6’
Call Abort
OFF
‘OFF’
Dial method
Tone/DTMF
‘TONE/DTMF’
Dialer Mode
Voice Dialer
‘VOICE DIALER’
Time
12:00:00
Put in actual time
Date
01/01/03
Put in actual date
VOICE DIALER SETUP:
Press , and press , until ‘4. VOICE DIALER SETUP’ is displayed and press .
Scroll through the menu until ‘4-1 PHONE NUMBERS’ is displayed and press .
Scroll through the menu until the required Telephone number (1-4) is displayed. The current setting
of each telephone number will also be displayed. To change the number press .
Enter the new telephone number (32 digits max.), press to save and exit, or press to exit
without saving. Press to insert a 3.6s pause in the dialing sequence. Press to move
the cursor left. Press to move the cursor right. Press to delete the character under the
cursor. Press and hold to erase the entire phone number.
Scroll through the menu until ‘4-3 RECORD VOICE’ is displayed and press .
Scroll through the available menu options until the required message type to be recorded is
displayed. 1) Main Alarm message, (12 seconds max). 2) Intruder Alarm message, (4 seconds max).
Latch Key setting; If you want to receive a call, when one of the users switches the alarm panel on or
off. Scroll through the top level programming menu until ‘6. LATCH KEY SETUP’ is displayed and
press . Selected users setup: This allows controls over which users the Latch Key facility
operates with when set to ‘Selected-Users’. Default setting: OFF . Scroll through the menu until ‘6-2
SELECTED USER SETUP’ is displayed and press . Scroll through the menu until the required
user number (1-6) to be configured is displayed. The current status will also be displayed.
TELEPHONE NUMBERS : Scroll through the menu until ‘6-3 PHONE NUMBERS’ is displayed and
press .Scroll through the menu until the required telephone number (1-2) is displayed. The
current setting will also be displayed. To change the number press . Enter the new telephone
number (32 digits max).
HAVE A LOT OF PLEASURE and visit our website: elro.eu
We wish you a lot of pleasure, safety and comfort with your ELRO 10-ZONE PRO ALARM SYSTEM
AP5500. We pay close attention to the quality of our products. In addition, we find installation and user
convenience very important. We are aware that there will always be points to improve points. Which
these are; nobody can tell us no better then you. We would like to hear from you what your experience
was during the preparation, installation and the use of this " ELRO 10-ZONE PRO ALARM SYSTEM ".
Go to www.elro.eu and give us your opinion about this ELRO 10-ZONE PRO ALARM SYSTEM.
Wishes and tips are very welcome. You will also find an overview of accessories, and other safety and
comfort products that will make your life a pleasurable and safer way of living.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Elro-AP5500---Pro-Alarm-System

  • alarm memory lampje brand en piept, hoe kan ik dit oplossen?? Gesteld op 16-4-2024 om 17:14

    Reageer op deze vraag Misbruik melden

  • Het betreft de Elro AP5500, het alarm memory lichtje blijft knipperen en het apparaat geeft regelmatig een piep toon, Het apparaat al gereset , via de sleutel, code, rondje en kruisje. Dan verdwijnt het ongeveer 5 minuten en het begint daarna weer te knipperen enz,. Wat is de oplossing? Gesteld op 29-1-2022 om 11:27

    Reageer op deze vraag Misbruik melden

  • Op mijn installatie knippert regelmatig het Led Status lampje. Weet iemand hoe ik dit uit kan zetten of wat dit betekent?. Het systeem functioneert overigens prima. Gesteld op 17-12-2021 om 16:11

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elro AP5500 - Pro Alarm System bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elro AP5500 - Pro Alarm System in de taal/talen: Engels als bijlage per email.

De handleiding is 1,39 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Elro AP5500 - Pro Alarm System

Elro AP5500 - Pro Alarm System Snelstart handleiding - Nederlands - 8 pagina's

Elro AP5500 - Pro Alarm System Gebruiksaanwijzing - Nederlands - 42 pagina's

Elro AP5500 - Pro Alarm System Snelstart handleiding - Deutsch - 10 pagina's

Elro AP5500 - Pro Alarm System Gebruiksaanwijzing - English - 49 pagina's

Elro AP5500 - Pro Alarm System Snelstart handleiding - Français - 9 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info