612699
74
Verklein
Vergroot
Pagina terug
1/94
Pagina verder
74 of 94
ELM327
ELM327DSJ Elm Electronics – Circuits for the Hobbyist
www.elmelectronics.com
We are occasionally asked what the maximum
data rate is that the ELM327 can handle. This is often
after someone has tried to monitor all data using the
default settings and has received a ‘BUFFER FULL’
error. It is difficult to say exactly what the maximum
rate is, however, as several factors are involved.
The CAN ‘engine’ inside the ELM327 is actually
configured with one receive register that accepts
messages from the data bus, and another register that
accepts messages from the first. As long as the
firmware empties the second register before the first
register needs it, there should not be any overflow
problems with this component. The ELM327 actually
moves the data quickly to temporary storage, so this is
never a problem.
It would be nice if all the firmware had to do was to
empty the second register, and wait for it to fill again,
but that is not so. It must also check for errors,
possibly queue a CAN response, format the received
Maximum CAN Data Rates
CAN Data
message message
message from ECU
11 bit/500 = 220
29 bit/250 = 520
min space
11 bit/500 = 16
29 bit/250 = 32
At 40% Bus Loading:
11 bit/500 = 354
29 bit/250 = 828
Notes:
- all times are in µsec
- times shown are averaged typical
- messages have 8 data bytes, and:
headers on (AT H1),
spaces off (AT S0),
linefeeds off (AT L0)
Moving Data
Processing Data
Sending Results
Rx register is empty and can
accept the next message
moves and error checks
500k = 29
250k = 41
all data is in the
send buffer
formatting & preparation
11 bit ID = 193
29 bit ID = 210
send time depends on message length and baud rate,
but on average is:
38.4k 115.2k 500k
11 bit ID 5180 1740 400
29 bit ID 6475 2175 500
this is a background task - the ELM327 can
do other things while it is sending RS232
message, convert it to ascii, load it into the RS232
transmit buffer, and then prepare to receive the next
message. These tasks can take a considerable time,
depending on what formatting options you have
chosen, and the baud rate that you select.
The diagram below shows these processes
grouped into blocks. The times shown are typical for
an ISO15765-4 message, and as you can see, vary
with both the length of the CAN message and the CAN
baud rate. All values shown are time measurements in
µsec (microseconds).
When a message arrives, the ELM327 moves
quickly to move the received bytes from the special
CAN registers, so that they do not affect the next
message that arrives. The data is then formatted (as
ASCII bytes) and placed into the RS232 transmit
buffer, for sending to the controlling processor. As long
as messages do not arrive at a rate that is faster than
the ELM327 can process them in, all messages will be
74

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Elm-327

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elm 327 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elm 327 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info