612699
67
Verklein
Vergroot
Pagina terug
1/94
Pagina verder
67 of 94ELM327DSJ Elm Electronics – Circuits for the Hobbyist
www.elmelectronics.com
ELM327
easily accomplished by sending a space or @
character, if the baud rate is 57.6 kbps or less. If using
higher baud rates, you may wish to consider
temporarily shifting to a lower baud rate and sending a
character, or possibly see if your software can
generate a ‘break’ signal for you. The break signal is
not always the same length, but is typically several
msec long (ie much longer than 128 µsec), and can
often be sent by USB through USB to RS232
conversion devices. You will have to experiment if
using other methods (Bluetooth or WiFi, for example).
The second method to have the ELM327 circuit go
back to full power is by having activity appear on the
OBD input pins. At the first sign of an active level, the
circuit will start its wakeup, and within seconds, will be
at full capability. Note that the logic is configured so
that it must see all quiet on the OBD inputs before it
will allow an automatic wakeup. This does not normally
present a problem, and is implemented so that you
can manually put the circuit to low power (AT LP),
even if there is activity on one of the OBD inputs.
Otherwise, the circuit would wake up immediately after
the AT LP.
When connected to protocols 3, 4 or 5 (ISO 9141-
2 or ISO 14230-4), there may be no OBD activity when
the vehicle is first turned on. In this case, you could not
rely on the activity monitor to wake the circuit and you
would have to look for other means.
The final method that is provided to wake up the
circuit is by way of the ignition monitor input and logic.
A low then high level at the IgnMon input will cause the
ELM327 to return to full power operation. Note that
PP 0E bit 2 does not have to be set for the IgnMon to
wake the circuit - the ELM327 always monitors this
pin, and will wake the circuit after the delay that is set
by PP 0E bit 1.
We are often asked if a switched ‘ignition’ voltage
is available at the vehicle’s diagnostic connector for
this purpose. It is not, so you must connect a separate
wire yourself. Often there are convenient places that
you can use for this - possibly the radio power, or the
connection to a convenience outlet.
Note that we present the pin 15 input as if it is an
ignition monitoring circuit, but in fact, it will monitor for
any change in voltage level (as long as the change is
stable for the debounce period). You might consider
connecting to other inputs (such as the 5V from a USB
cable, for example) - just be sure to protect the
ELM327 input circuitry from transients. This usually
just requires a series resistor of 1K to 10K in value.
One alternative is to provide a pullup resistor to
allow waking of the ELM327 with a momentary
pushbutton switch:
2.2K
47K
+5V
If the circuit is in low power mode, a momentary
push of the button will wake it up. This is just one of
the many ways in which you can use this input.
One final note has to do with the changes to the
startup process, beginning with firmware version 2.0.
Initially (with v1.4 and v1.4b), the ELM327 simply used
a warm start command (AT WS) to exit from the low
power mode. The positive feedback that we received
from our ELM329 changes has led us to also change
the wakeup process for the ELM327.
Now, on switching back to full power operation,
the ELM327 performs a warm start, but retains the
following settings:
E0/1 H0/1 L0/1 M0/1
R0/1 D0/1 S0/1 AT0/1/2
CAF0/1 CFC0/1 CSM0/1 CEA
CTM1/5 JTM1/5 AL/NL IIA
In addition, the ISO/KWP baud rate is retained and
the current protocol is not changed (but it is closed, so
will require initialization).
This has discussed how to have the ELM327 go to
low power operation, and wake from it. While in the
low power mode, the question of ‘just how low is the
power consumption’ arises. We discuss that in the
‘Modifications for Low Power Standby Operation’
section, which is on page 84.
Power Control (continued)
67

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Elm-327

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elm 327 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elm 327 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info