612699
49
Verklein
Vergroot
Pagina terug
1/94
Pagina verder
Restoring Order
There may be times when it seems the ELM327 is
out of control, and you will need to know how to
restore order. Before we continue to discuss modifying
too many parameters, this seems to be a good point to
discuss how to ‘get back to the start’. Perhaps you
have told the ELM327 to monitor all data, and there
are screens and screens of data flying by. Perhaps the
IC is now responding with ‘NO DATA’ when it did work
previously. This is when a few tips may help.
The ELM327 can always be interrupted from a
task by a single keystroke from the keyboard. As part
of its normal operation, checks are made for received
characters and if found, the IC will stop what it is doing
at the next opportunity. Often this means that it will
continue to send the information on the current line,
then stop, print a prompt character, and wait for your
input. The stopping may not always seem immediate if
the RS232 send buffer is almost full, though – you will
not actually see the prompt character until the buffer
has emptied, and your terminal program has finished
printing what it has received.
There are times when the problems seem more
serious and you don’t remember just what you did to
make them so bad. Perhaps you have ‘adjusted’ some
of the timers, then experimented with the CAN filter, or
perhaps tried to see what happens if the header bytes
are changed. All of these can be reset by sending the
‘set to Defaults’ AT Command:
>AT D
OK
This will often be sufficient to restore order, but it
can occasionally bring unexpected results. One such
surprise will occur if you are connected to a vehicle
using one protocol, but the saved (default) protocol is
a different one. In this case, the ELM327 will close the
current session and then change the protocol to the
default one, exactly as instructed.
If the AT D does not bring the expected results, it
may be necessary to do something more drastic - like
resetting the entire IC. There are a few ways that this
can be performed with the ELM327. One way is to
simply remove the power and then reapply it. Another
way that acts exactly the same way as a power off and
then on is to send the full reset command:
>AT Z
It takes approximately one second for the IC to
perform this reset, initialize everything and then test
the four status LEDs in sequence. A much quicker
option is available with the ELM327, however, if the
led test is not required – the ‘Warm Start’ command:
>AT WS
The AT WS command performs a software reset,
restoring exactly the same items as the AT Z does, but
it omits the LED test, making it considerably faster.
Also, it does not affect any baud rates that have been
set with the AT BRD command (which AT Z does), so
is essential if you are modifying the RS232 baud rates
with software.
Any of the above methods should be effective in
restoring order while experimenting. There is always
the chance that you may have changed a
Programmable Parameter, however, and are still
having problems with your system. In this case, you
may want to simply turn off all of the Programmable
Parameters (which forces them to their default values).
To do so, send the command:
>AT PP FF OFF
which should disable all of the changes that you have
made. Since some of the Programmable Parameters
are only read during a system reset, you may have to
follow this command with a reset command:
>AT Z
after which, you can start over with what is essentially
a device with ‘factory settings’. There may be times
when even this command is not recognized, however.
If that is the case, you will need to use the hardware
method of turning the PPs off. See the section on
‘Programmable Parameters’ (pages 68 and 69) for
more details.
49 of 94ELM327DSJ Elm Electronics – Circuits for the Hobbyist
www.elmelectronics.com
ELM327
49

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Elm-327

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elm 327 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elm 327 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info