612699
28
Verklein
Vergroot
Pagina terug
1/94
Pagina verder
28 of 94
ELM327
ELM327DSJ Elm Electronics – Circuits for the Hobbyist
www.elmelectronics.com
attempting to connect to one of them.
V0 and V1 [ Variable data lengths off or on ]
Many CAN protocols (ie ISO 15765-4) expect to
send eight data bytes at all times. The V0 and V1
commands may be used to override this behaviour (for
any CAN protocol) should you wish.
Choosing V1 will cause the current CAN protocol
to send variable data length messages, just as bit 6 of
PP 2C and PP 2E do for protocols B and C. It does not
matter what the protocol should be doing - V1 will
override that. This allows experimenting with variable
data length messages on demand.
If you select V0 (the default setting), the forced
sending of variable length CAN messages is turned
off. The format of the sent messages reverts to the
protocol’s settings.
WM [1 to 6 bytes] [ set Wakeup Message to… ]
This command allows the user to override the
default settings for the wakeup messages (sometimes
known as the ‘periodic idle’ messages). Simply provide
the message that you wish to have sent (typically three
header bytes and one to three data bytes), and the
ELM327 will add the checksum and send them as
required, at the rate determined by the AT SW setting.
Default settings will send the bytes 68 6A F1 01 00
for ISO 9141, and C1 33 F1 3E for KWP.
WS [ Warm Start ]
This command causes the ELM327 to perform a
complete reset. It is very similar to the AT Z command,
but does not include the power on LED test. Users
may find this a convenient way to quickly ‘start over’
without having the extra delay of the AT Z command.
If using variable RS232 baud rates (ie AT BRD
commands), it is preferred that you reset the IC using
this command rather than AT Z, as AT WS will not
affect the chosen RS232 baud rate.
Z [ reset all ]
This command causes the chip to perform a
complete reset as if power were cycled off and then on
again. All settings are returned to their default values,
and the chip will be put into the idle state, waiting for
characters on the RS232 bus. Note that any baud rate
that was set with the AT BRD command will be lost,
and the ELM327 will return to the default baud rate
setting.
@1 [ display the device description ]
This command displays the device description
string. The default text is ‘OBDII to RS232 Interpreter’.
@2 [ display the device identifier ]
A device identifier string that was recorded with
the @3 command is displayed with the @2 command.
All 12 characters and a terminating carriage return will
be sent in response, if they have been defined. If no
identifier has been set, the @2 command returns an
error response (‘?’). The identifier may be useful for
storing product codes, production dates, serial
numbers, or other such codes.
See the ‘Programming Serial Numbers’ section for
more information.
@3 cccccccccccc [ store the device identifier ]
This command is used to set the device identifier
code. Exactly 12 characters must be sent, and once
written to memory, they can not be changed (ie you
may only use the @3 command one time). The
characters sent must be printable (ascii character
values 0x21 to 0x5F inclusive).
If you are developing software to write device
identifiers, you may be interested in the ELM328 IC, as
it allows multiple writes using the @3 command (but it
can not send OBD messages).
AT Command Descriptions (continued)
28

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Elm-327

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elm 327 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elm 327 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info