612699
17
Verklein
Vergroot
Pagina terug
1/94
Pagina verder
17 of 94
ELM327
ELM327DSJ Elm Electronics – Circuits for the Hobbyist
www.elmelectronics.com
continually monitor for this type of message for you,
following multi-segment transport protocols as
required. Note that a combination of masks and filters
could be set to provide a similar output, but they would
not allow multiline messages to be detected. The DM1
command adds the extra logic that is needed for
multiline messages.
This command is only available when a CAN
Protocol (A, B, or C) has been selected for J1939
formatting. It returns an error if attempted under any
other conditions.
DP [ Describe the current Protocol ]
The ELM327 automatically detects a vehicle’s
OBD protocol, but does not normally report what it is.
The DP command is a convenient means of asking
what protocol the IC is currently set to (even if it has
not yet ‘connected’ to the vehicle).
If a protocol is chosen and the automatic option is
also selected, AT DP will show the word 'AUTO' before
the protocol description. Note that the description
shows the actual protocol names, not the numbers
used by the protocol setting commands.
DPN [ Describe the Protocol by Number ]
This command is similar to the DP command, but
it returns a number which represents the current
protocol. If the automatic search function is also
enabled, the number will be preceded with the letter
‘A’. The number is the same one that is used with the
set protocol and test protocol commands.
E0 and E1 [ Echo off or on ]
These commands control whether or not the
characters received on the RS232 port are echoed
(retransmitted) back to the host computer. Character
echo can be used to confirm that the characters sent
to the ELM327 were received correctly. The default is
E1 (or echo on).
FC SD [1-5 bytes] [ Flow Control Set Data to… ]
The data bytes that are sent in a CAN Flow
Control message may be defined with this command.
One to five data bytes may be specified, with the
remainder of the data bytes in the message being
automatically set to the default CAN filler byte, if
required by the protocol. Data provided with this
command is only used when Flow Control modes 1 or
2 have been enabled.
FC SH hhh [ Flow Control Set Header to… ]
The header (or more properly ‘CAN ID’) bytes
used for CAN Flow Control messages can be set using
this command. Only the right-most 11 bits of those
provided will be used - the most significant bit is
always removed. This command only affects Flow
Control mode 1.
FC SH hhhhhhhh [ Flow Control Set Header to… ]
This command is used to set the header (or ‘CAN
ID’) bits for Flow Control responses with 29 bit CAN ID
systems. Since the 8 nibbles define 32 bits, only the
right-most 29 bits of those provided will be used - the
most significant three bits are always removed. This
command only affects Flow Control mode 1.
FC SM h [ Flow Control Set Mode to h ]
This command sets how the ELM327 responds to
First Frame messages when automatic Flow Control
responses are enabled. The single digit provided can
either be ‘0’ (the default) for fully automatic responses,
‘1’ for completely user defined responses, or ‘2’ for
user defined data bytes in the response. Note that FC
modes 1 and 2 can only be enabled if you have
defined the needed data and possibly ID bytes. If you
have not, you will get an error. More complete details
and examples can be found in the Altering Flow
Control Messages section (page 60).
FE [ Forget Events ]
There are certain events which may change how
the ELM327 responds from that time onwards. One of
these is the occurrence of a fatal CAN error (ERR94),
which blocks subsequent searching through CAN
protocols if PP 2A bit 5 is ‘1’. Normally, an event such
as this will affect all searches until the next power off
and on, but it can be ‘forgotten’ using software, with
the AT FE command.
Another example is an ‘LV RESET’ event which
will prevent searches through CAN protocols if PP 2A
bit 4 is ‘1’. It may also be forgotten with the AT FE
command.
AT Command Descriptions (continued)
17

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Elm-327

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elm 327 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elm 327 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info