741400
6
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
6 IT500CLOUD
BUS CONNECTION
WARNING! Always connect and disconnect the devices to the bus with the control panel not
powered (mains and battery disconnected).
Refer to the installation manual of MP500/8 control panel with regard to the cable section,
distances and extensions.
Wires with cross-section area of 0.5 mm² or larger must comply with IEC 60332-1-2; wires
with cross-section area smaller than 0.5 mm² must comply with IEC 60332-2-2.
Connect the device to the BUS using terminals +, +D, D and (Legend Fig. 1 - E and Fig.3)
The device can be connected to the BUS in cascade, star or mixed mode.
The total length of all bus stretches must not exceed 400 m.
CONFIGURATION
After having positioned and wired the device to the bus of the control unit (operation to be
performed with the control unit not powered) proceed with:
Device acquisition on the bus
Proceed as follows to perform the acquisition procedure:
1. Enter in the acquisition mode from keypad MP500/8 control panel, by typing > Code > Technical
>OK.
2. Press the programming button PROG when the message "Acquisition in progress" appears
on the display (see Legend Fig.1 - A),
3. The keypad buzzer sounds and the "Acquisition in progress" message disappears.
4. The LED on the board blink quickly three times to indicate that the address has been acquired.
5. Then, the LED starts blinking in Access Point mode with normal operation.
During normal operation, by pressing the programming button PROG (see Legend Fig.1 - A), the
board runs a short LED sequence, which specifies the address acquired.
The IT500CLOUD interface board being acquired, is recognised by the MP500/8 control
panel as a keypad and the first available address is assigned to it. Pay attention to the number of
keypads already present in the system. The maximum number allowed is 8 (e.g. if a board is
acquired there may be up to 7 keypads in the system).
Device network parameter configuration
The device can work both either with Ethernet network or with WiFi using your home network or
one available in DHCP mode. By default, the device is in "Access Point" mode, it will be
necessary to define the operating mode through the “My Elkron Family” App.
NOTE: If the Ethernet connection is used, this mode can be enabled directly, following the
instructions below:
When the interface is operating (two blink every 8 seconds) press the “PROG” button 5 times”.
After the command wait a few moments (about 20 seconds), the interface restarts and goes into
the chosen mode (Ethernet).
Power off the interface, wait 10 seconds, and power up the interface again.
Proceed as follows to configure:
Power the control unit, if you have chosen to connect it to your home network via cable (Ethernet),
connect it to the connector on the device (see legend Fig. 1 - F).
Start the My Elkron Family application previously installed and proceed as follows:
Press the “Other” button.
Select the "Add Device" menu.
Follow the instructions which will appear on the guided menu.
If all the parameters were programmed correctly, the device is ready to be managed via the My
Elkron Family App.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elkron IT500CLOUD bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elkron IT500CLOUD in de taal/talen: Engels, Frans, Italiaans als bijlage per email.

De handleiding is 0,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info