741401
8
Verklein
Vergroot
Pagina terug
1/18
Pagina verder
8 DS80TC2S-001
Walk Test
Run a Walk test before installing the detector at the chosen point:
1. Make sure that the Walk Test function has been activated on the control unit.
2. Press the function button once.
3. Check the RSSI value on the control unit.
4. Proceed with the installation.
Restoring default settings
If the detector was not learnt correctly by the control unit, or if you want to remove it and associate it with another control unit,
restore the default settings to eliminate the settings and the information stored in the detector before being able to associate it with
another control unit. To restore the default settings:
1. Remove the batteries and refit them. IMPORTANT: The detector must be reset within three minute from switch-on.
2. The tamper switch must be open (released).
3. Hold the function button pressed 10 seconds, then release it when the camera generates a light signal.
4. The detector was reset to the default factory settings and all the previous network information were deleted. The detector
is no longer present on the "Devices" page of the local control panel.
<NOTE>
If you want to run the learning procedure of the detector again on a control unit after a factory reset, follow all the steps listed
in the “Connecting to the system” paragraph again, starting from extracting the batteries from their housing.
Installation
Installation guidelines
The detector was designed to be mounted on a flat surface or in a corner by means of the angle bracket using the fixing
screws and the anchor bolts provided.
The base has hole arrangements where the plastic is thinner for mounting. The two arrangements are used to fix on a
surface. While the three holes are used to fix the angle bracket.
It is advisable to install the detector as shown below:
-
In the point in which a possible intruder would normally cross the field of vision of the detector.
-
At a height of 1.9 - 2 m from the ground for optimal performance.
In a corner to have the widest view possible.
In a point in which the field of vision is not obstructed, e.g. by curtains, ornaments etc.
Restrictions
Do not position the detector pointing directly towards a door protected by a door contact, because the wireless signals of
the door contact and of the detector could be transmitted in the same instant and cancel themselves out.
Do not install the detector so that it is completely exposed to direct sunlight.
Avoid installing the detector in areas in which devices which could cause sudden changes of temperature in the detection
area are present, such as air conditioning units, radiators etc.
Avoid the presence of large size obstacles in the detection area.
Do not point it directly towards sources of heat, such as stoves or boilers, or over radiators.
Avoid moving objects in the detection area, such as curtains, hanging objects etc.
Detector installation
Surface installation:
1. Loosen the fixing screw and gently lift the cover, taking care not to lose the rubber button over the tamper switch.
2. Perforate the hole arrangements on the base for fixing on a surface.
3. Using the two holes as template, drill the holes corresponding to the surface.
4. Insert the anchor bolts if the device is fixed to plaster or bricks.
5. Screw the base into the anchor bolts.
6. Reposition the cover onto the base.
Hole provisions for fixing on
surface (x 2)
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elkron IR600FC-N bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elkron IR600FC-N in de taal/talen: Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 0,52 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Elkron IR600FC-N

Elkron IR600FC-N Snelstart handleiding - Deutsch, English, Français, Italiano - 8 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info