741424
6
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
6/16
JP1
JP3
JP2
1
2
3
+IN -IN SH -OUT +OUT PC
CC
H1
JP4
- +
GENERAL DESCRIPTION
Based on a microcontroller and equipped with a short circuit isolator, the IO501 is an output module
(OM) with a dry contact output to be used with Elkron FAP series control panels. The module is directly
powered from the detection circuit and it doesn’t need an external power supply. A jumper is used to
select the normally open or normally closed contact type. The module has an input for supervise the
external local power supply of the handled device: a loss or presence of the local power supply is
signalled from the module to the control panel. The bi-colour LED (green-red), in operating mode,
indicates the module condition while, in service mode, it can be used to show the detector’s address by a
special function activated from the control panel. Delay between output feedback and actual output
control (hold-off delay) can be programmed in the control panel. This delay is expressed in seconds and it
covers a range between 0 and 255 seconds with 1 sec. steps. The default value is 0.
For further information refer to the FAP series Control Panel’s programming manual.
ADDRESSING
The address (1-128) is software set and stored in a non-volatile memory.
The module can be addressed, in manual or automatic mode from the Control Panel.
For further details see the Control Panel’s programming manual.
TERMINAL BOARDS
Nr.
Description
+IN
Detection circuit positive input
-IN
Detection circuit negative input
SH
Detection circuit input shield
-OUT
Detection circuit negative output
+OUT
Detection circuit positive output
PC
NO/NC contact switch
CC
Common contact switch
JP1: Closed: default setting
Open: Power off module
JP2: Closed: electrical connection between detection line positive input and detection line positive
output
Open: default setting
JP3: Position 1-2: contact normally open (NO).
Default setting
Position 2-3: contact normally closed (NC)
JP4: Connector for per local 24Vdc supervision. Use the supplied cable.
Red wire: 24Vdc positive input
Black wire: 24Vdc negative input
It’s possible to define in control panel the fault signaling for absence or presence of the local voltage.
ENGLISH
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elkron IO501 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elkron IO501 in de taal/talen: Engels, Italiaans, Spaans als bijlage per email.

De handleiding is 0,52 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info