741426
5
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
mode after three minutes and goes back to normal mode. In order to set the detector to constant Test mode, positioning the
DIP Switch 1 the reference to the DIP Switch position table.
SLEEP TIME
time between the detection of a movement and the next movement
<
<
N
N
O
O
T
T
E
E
>
>
In such cases it is advisable to use the Walk Test function and check the outcome on the App and portal where available
and / or on the system's local devices (eg keyboards).
Mounting and installation method
Step 1: After having performed the Walk Test to confirm that the detector is within the coverage range, select corner or surface
mounting.
Step 2: Loosen the screws and remove the cover.
Step 3: According to the user's preferences, mount the detector in the required position with or without rotating bracket.
Mounting without rotating bracket:
The rear base of the detector is provided with a hole arrangement when the plastic is thinner to allow mounting. The
two hole arrangements (A) are used to fix on a surface while the four hole arrangements (C) are used for fixing in a
corner, as shown in the following figure.
<
<
N
N
O
O
T
T
E
E
>
>
After having perforated the hole arrangements, check that the device is waterproof and restore waterproofing, if
necessary, e.g. with silicone.
1) Perforate the appropriate hole arrangements on the cover of the base. Use arrangements "A" for mounting on surface.
Use arrangements "C" for mounting in corner.
2) Using the template for the hole,make two holes in the flat surface or four holes in the corner
surface.
3) Insert the anchor bolts if the device is fixed to plaster or bricks.
4) Install the base cover in the anchor bolt with the mounting screws provided.
5) Reposition the upper cover on the base and firmly press the upper part until it clicks (as shown
on the right).
6) Tighten the locking screw.
Mounting with rotating bracket:
A rotating bracket is provided to allow a flexible mounting option. This allows a rotating bracket to be fixed to a surface/in
a corner and to an arm of the bracket to be fixed to the detector. Once installed, the detector may be separated easily
from the bracket to replace the batteries, for example, and then fixed back again with equal ease. This also makes it
possible to adjust the horizontal detector for better coverage.
1) Using the rotating shaft as template, make holes in the mounting site,
either on a surface or in a corner: 2 holes in position B for a surface, 4
holes in position D for an angle.
2) Insert the anchor bolts if the device is fixed to plaster or bricks.
3) Fasten the rotating bracket in the anchor bolts with the flat side in direction
of the wall. The arm of the bracket must face towards the person
performing the mounting operation, with the joint on top.
4) Fasten the arm of the bracket to the cover of the base of the detector with
the pointy ends facing the opposite directions with respect to the detector,
with the joint on top.
5) Arrange the detector on the hooks of the rotating bracket.
6) Adjust the detection angle arranging the arm of the bracket on one of the holes of the top of the rotating bracket then
tighten the top screw as shown.
Surface
mounting
Corner
mounting
Fastening screw
Fastening screw
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elkron EIR600 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elkron EIR600 in de taal/talen: Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 0,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info