Handleiding Elite Arion Mag (pagina 11 van 36) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools)

782482

Verklein

Vergroot

Pagina terug

1/36

Pagina verder

Thank you for choosing the ARION MAG

roller

01_GENERAL SAFETY WARNINGS

Before using your trainer, carefully read the warnings listed

below for your health and safety.

1. The appliance is not to be used by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction.

2. Children being supervised not to play with the appliance.

3. Before beginning a training programme, undergo a

physical examination certifying good health.

4. Choose a training level compatible with your physical

endurance and the status of your health.

5. When using the trainer, select a training program and

adjust it so that it is compatible with your fitness level and

health.

6. If you feel particularly fatigued or sore while exercising,

stop using the trainer immediately and consult your doctor.

The above warnings are general and not exhaustive of all

the precautions that should be taken for the proper and

safe use of the trainer; which is solely the responsibility of

the user.

02_INSTRUCTIONS FOR USE

The roller is a training tool enabling users to get into top

shape for cycling.

Its incorporated magnetic resistance unit featuring three

levels offers smoother and more even and gradual

resistance.

The rollers, of technopolymer material, are specially

shaped to guarantee better control of pace.

High quality cylindrical bearings ensure many years of

trouble free and quiet operation.

The frame of the ARION MAG is very practical, light,

manageable, easy to use and takes up little space.

Frame can be folded for easier storage or carrying.

It is recommended for users of all levels.

IMPORTANT

Pay attention to the position of hands when closing the

roller, to avoid squashing them between the two side

members

03_NAME AND LIST OF COMPONENTS

N°3 Side members Ref. A

N1 Longitudinal member with resistance Ref. B

N°4 Rectangular covers Ref. C

N°1 Slider positions 0-1-2 Ref. D

N°1 Front roller Ref. E

N°1 Middle roller Ref. F

N°1 Rear roller Ref. G

N°1 Drive belt Ref. H

N°1 Allen key Ref. I

04_ASSEMBLY

Your ARION MAG roller should arrive fully assembled,

checked and ready for use.

05_USE

Before starting to use your ARION MAG it is necessary to

adjust the centre distance of the rollers to make them

compatible with your bicycle’s wheelbase.

This adjustment must be carried out as follows:

1) Measure the distance between the centres of the wheels

of the bicycle to be used on the ARION MAG (Fig.2). We

will call this dimension “X”.

2) The distance from the intermediate point between the

two rear rollers to the middle of the ARION MAG front roller,

which we will call “Y” (Fig.3), must match or be as near as

possible to dimension “X” . The axle of the ARION MAG

front roller must be positioned in the hole of the ARION

MAG frame whose measurement given on the graduated

scale is closest to dimension “X” (Fig.4).

ATTENTION: Dimension “Y” must be equal to or slightly

greater than “X”. The rollers can be adjusted to adapt them

to bicycles whose wheelbase is 944-1124 mm (37 to 44

inches).

3) To change Y it is necessary to shift the front roller E.

4) Fold the ARION MAG until the drive belt H slackens.

5) Loosen the drive belt H , making it come off the

respective front and rear guides.

6) Unfold the ARION MAG back into the open position.

7) Remove the rectangular covers C from both front

longitudinal members (with aid of a screwdriver if

necessary), and the screws and washers from the front

roller on both sides, using the Allen key I) supplied (Fig. 5).

8) Pull the roller out from its original position.

9) Position the roller in the appropriate seat in the holes in

the frame, so that X matches Y.

10) Refit the screws and the washers in the special holes,

but do not tighten them down.

11) Close the ARION MAG, position the drive belt H on the

guide of the front roller E and middle roller F.

12) Unfold the ARION MAG into open position again.

13) Check the position of the front roller E , putting your

bicycle on the rollers and checking that the axle for the

front wheel sits directly above the front roller.

14) Once the front roller E is positioned, tighten the

screws (do not over-tighten as this could warp the side

members).

15) Close the sides with the rectangular covers C. The

ARION MAG is now ready to use.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Elite Arion Mag Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info