Handleiding Elica ALBA PYRAMID WALL (pagina 14 van 14) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins)

471165

Verklein

Vergroot

Pagina terug

1/14

Pagina verder

DE Montage- und Gebrauchsanweisung

EN Instruction on mounting and use

FR Prescriptions de montage et mode d’emploi

NL Montagevoorschriften en gebruiksaanwijzingen

IT Istruzioni di montaggio e d'uso

ES Montaje y modo de empleo

PT Instruções para montagem e utilização

EL ΟΔΗΓΙΕΣ ΣΥΝΑΡΜΟΛΟΓΗΣΗΣ ΚΑΙ ΧΡΗΣΗΣ

PL Instrukcja montażu i obsługi

CS Návod na montáž a používání

SK Návod k montáži a užití

HU Felszerelési és használati utasítás

RU Инструкции по монтажу и эксплуатации

BG Инструкции за монтаж и употреба

RO INSTRUCTII DE MONTAJ SI FOLOSIRE

SL Navodila za montažo in uporabo

HR Uputstva za montažu i za uporabu

NO Instrukser for montering og bruk

SV Monterings- och bruksanvisningar

DA Bruger- og monteringsvejledning

TR Montaj ve kullanım talimatları

EN - Instruction on mounting and use

Closely follow the instructions set out in this manual. All

responsibility, for any eventual inconveniences, damages or

fires caused by not complying with the instructions in this

manual, is declined. The extractor hood has been designed

exclusively for domestic use.

The hood can look different to that illustrated in the

drawings in this booklet. The instructions for use,

maintenance and installation, however, remain the same.

! It is important to conserve this booklet for consultation at

any moment. In the case of sale, cession or move, make

sure it is together with the product.

! Read the instructions carefully: there is important

information about installation, use and safety.

! Do not carry out electrical or mechanical variations on the

product or on the discharge conduits.

Note: the elements marked with the symbol “(*)” are optional

accessories supplied only with some models or elements to

purchase, not supplied.

Caution

WARNING! Do not connect the appliance to the mains until

the installation is fully complete.

Before any cleaning or maintenance operation, disconnect

hood from the mains by removing the plug or disconnecting

the mains electrical supply.

Always wear work gloves for all installation and maintenance

operations.

The appliance is not intended for use by children or persons

with impaired physical, sensorial or mental faculties, or if

lacking in experience or knowledge, unless they are under

supervision or have been trained in the use of the appliance

by a person responsible for their safety.

This appliance is designed to be operated by adults, children

should be monitored to ensure that they do not play with the

appliance.

This appliance is designed to be operated by adults. Children

should not be allowed to tamper with the controls or play with

the appliance.

Never use the hood without effectively mounted grating!

The hood must NEVER be used as a support surface unless

specifically indicated.

The premises where the appliance is installed must be

sufficiently ventilated, when the kitchen hood is used together

with other gas combustion devices or other fuels.

The ducting system for this appliance must not be connected

to any existing ventilation system which is being used for any

other purpose such as discharging exhaust fumes from

appliances burning gas or other fuels.

The flaming of foods beneath the hood itself is severely

prohibited.

The use of exposed flames is detrimental to the filters and

may cause a fire risk, and must therefore be avoided in all

circumstances.

Any frying must be done with care in order to make sure that

the oil does not overheat and ignite.

Accessible parts of the hood may became hot when used with

cooking applicance.

With regards to the technical and safety measures to be

adopted for fume discharging it is important to closely follow

the regulations provided by the authorised authorities.

The hood must be regularly cleaned on both the inside and

outside (AT LEAST ONCE A MONTH).

This must be completed in accordance with the maintenance

instructions provided in this manual). Failure to follow the

instructions provided in this user guide regarding the cleaning

of the hood and filters will lead to the risk of fires.

Do not use or leave the hood without the lamp correctly

mounted due to the possible risk of electric shocks.

We will not accept any responsibility for any faults, damage or

fires caused to the appliance as a result of the non-

observance of the instructions included in this manual.

This appliance is marked according to the European directive

2002/96/EC on Waste Electrical and Electronic Equipment

(WEEE). By ensuring this product is disposed of correctly, you

will help prevent potential negative consequences for the

environment and human health, which could otherwise be

caused by inappropriate waste handling of this product.

The symbol

on the product, or on the documents

accompanying the product, indicates that this appliance may

not be treated as household waste. Instead it should be taken

to the appropriate collection point for the recycling of electrical

and electronic equipment. Disposal must be carried out in

accordance with local environmental regulations for waste

disposal.

Use

The hood is designed to be used either for exhausting or filter

version.

Ducting version

In this case the fumes are conveyed outside by means of a

special pipe connected with the connection ring located on top

of the hood.

Attention! The exhausting pipe is not supplied and must be

purchased apart.

Diameter of the exhausting pipe must be equal to that of the

connection ring.

In the horizontal runs the exhausting pipe must be slightly

slanted (about 10°) and directed upwards to vent the air easily

from the room to the outside.

Attention! If the hood is supplied with active charcoal filter,

then it must be removed.

Connect the hood and discharge holes on the walls with a

diameter equivalent to the air outlet (connection flange).

Using the tubes and discharge holes on walls with smaller

dimensions will cause a diminution of the suction performance

and a drastic increase in noise.

Any responsibility in the matter is therefore declined.

! Use a duct of the minimum indispensible length.

! Use a duct with as few elbows as possible (maximum

elbow angle: 90°).

! Avoid drastic changes in the duct cross-section.

! Use a duct with an as smooth as possible inside.

! The duct must be made of certified material.

Filter version

One active charcoal filter is needed for this and can be

obtained from your usual retailer.

The filter removes the grease and smells from the extracted

air before sending it back into the room through the upper

outlet grid.

Installation

The minimum distance between the supporting surface for the

cooking equipment on the hob and the lowest part of the

range hood must be not less than 50cm from electric cookers

and 65cm from gas or mixed cookers.

If the instructions for installation for the gas hob specify a

greater distance, this must be adhered to.

Electrical connection

The mains power supply must correspond to the rating

indicated on the plate situated inside the hood. If provided with

a plug connect the hood to a socket in compliance with current

regulations and positioned in an accessible area, after

installation. If it not fitted with a plug (direct mains connection)

or if the plug is not located in an accessible area, after

installation, apply a double pole switch in accordance with

standards which assures the complete disconnection of the

mains under conditions relating to over-current category III, in

accordance with installation instructions.

Warning! Before re-connecting the hood circuit to the mains

supply and checking the efficient function, always check that

the mains cable is correctly assembled.

The hood is provided with a special power cable ; if the cable

is damaged, request a new one from Technical Service.

Mounting

Expansion wall plugs are provided to secure the hood to most

types of walls/ceilings. However, a qualified technician must

verify suitability of the materials in accordance with the type of

wall/ceiling. The wall/ceiling must be strong enough to take

the weight of the hood. Do not tile, grout or silicone this

appliance to the wall. Surface mounting only.

Certain models are supplied WITHOUT panels (Panelable

Version) in order to allow personalization of the product.

Attention!: The materials used to panel the Panelable

Version must meet the requirements of the General

European Household Appliance Standard EN 60335-1 and

in particular the cooker hood standard EN 60335-2-31.

Elica S.p.A. Refuses all responsibility for any damage

deriving from the use of materials not complying with

such requirements.

Attention!: Do not connect the appliance to the power

supply system until the installation of the hood and the

panels has been completed.

On the first pages of this manual you will find the technical

drawings necessary to determine the right dimensions of the

panels and the fixing points.

Operation

Use the high suction speed in cases of concentrated kitchen

vapours. It is recommended that the cooker hood suction is

switched on for 5 minutes prior to cooking and to leave in

operation during cooking and for another 15 minutes

approximately after terminating cooking.

The hood is equipped with a “TOUCH” device to control the

lights and speed.

For the correct use please carefully read the intructions below.

The cooker hood can be controlled through a remote control

available as accessory kit (see the paragraph relating to the

functioning of the remote control).

Automatic start-up function

The hood is equipped with a temperature sensor which

activates the motor to the first suction speed (power) in the

event that the room temperature in the surrounding area is

higher than 70°C.

The user may switch off or modify the suction speed (power)

(see paragraph “suction speed (power) control”).

Suction speed (power) control

The suction speed (power) is cyclical depending on the speed

sequence “stand-by – 1-2-3-4- Stand by -1-2-...” therefore

every time the T1 button is pressed on the control panel, the

suction speed (power) is increased by one level, in order to

switch off (stand-by) if the button is pressed again when the

hood is in suction speed (power) 4.

The hood may be switched off (stand-by) while the hood is set

on any speed by holding down the T1 button on the control

panel for a bit longer (more than 3 seconds).

The hood's suction speed (power) may be determined as the

control panel is equipped with a LED light that changes colors

as follows, depending on the suction speed (power):

Hood in stand-by: LED LIGHT SWITCHED OFF

suction speed (power) -GREEN LED LIGHT

suction speed (power) – ORANGE LED LIGHT (amber)

suction speed (power) - RED LED LIGHT

suction speed (power) - RED LED LIGHT (FLASHING)

Note: The 4

suction speed (power) stays on for 5 minutes,

after which the suction motor will position itself on the 2

speed.

If pressed again, the suction motor will switch off (stand-by).

Grease filters need cleaning: FLASHING GREEN LED light

(read instructions found under “Reset and configuration for

filter saturation signal”)

Coal filters must be cleaned or replaced: FLASHING

ORANGE (amber) LED light (read instructions found under

“Reset and configuration for filter saturation signal”)

Note: The reset procedure may be activated by both the

control panel and the remote control.

Center light check

The center light may be switched on and off by pressing the

T2 button on the control panel.

Side light check (when scheduled)

The side lights may be switched on and off by pressing AND

HOLDING DOWN the T2 button on the control panel.

HOLDING DOWN the button, besides permitting to switch the

hood on and off, it also regulates the light intensity given from

the lights.

Note: The switching on and off functions (and regulating

function) alternate.

The regulation of the light intensity is not available for hoods

with neon lights.

Reset and configuration for filter saturation signal

Switch on hood to any speed (see above paragraph “Suction

speed (power) selection”)

Reset grease filter saturation signal (FLASHING GREEN

LIGHT on control panel)

First proceed with filter maintenance as described in

corresponding paragraph.

Press and hold down (for more than 3 seconds) the T1 button

on the control panel, the LED light will stop flashing indicating

that the signal reset has been carried out, the hood will switch

off.

Reset coal filter saturation signal (FLASHING ORANGE

(amber) LED light)

First proceed with filter maintenance as described in

corresponding paragraph.

Press and hold down (for more than 3 seconds) the T1 button

on the control panel, the LED light will stop flashing indicating

that the signal reset has been carried out, the hood will switch

off.

Coal filter saturation signal disactivaction (for particular

applications)

Switch off hood (see above paragraph “suction speed (power)

selection”).

Press and hold down (for more than 5 seconds) the T1 button

on the control panel, the LED light will start flashing GREEN

indicating that the coal filter saturation signal has been

disactivated.

In order to reactivate the coal filter saturation signal, repeat

operation, the LED light will flash ORANGE (amber)

Using the remote control

The remote control is able to control all the functions of the

hood:

Select the suction speed (power)

Control the central light

Control the lateral lights

Reset e configure the saturation of the filters signal

Selecting the suction speed (power):

Press the "◄" key or the "►" key until you see the symbol

relating to the “Select the suction speed (power)” function.

Press the “+” key or the “-” key or the "■" key respectively to

increase or diminish or switch off (stand-by) the speed

(suction power).

Controlling the central light:

Press the "◄" key or the "►" key until seeing the symbol

relating to the “Controlling the central light” function on the

remote control.

The central light can be switched on and off in two ways:

1. Press the “+” key or the “-” key respectively to switch the

central light (ON) or (OFF).

2. Press the "■" key to change the state of the light from

(OFF) to (ON) or vice versa.

Controlling the lateral lights:

Press the "◄" key or the "►" key until seeing the symbol

relating to the “Controlling the lateral lights” function on the

remote control.

Press the "■" key to change the state of the lateral lights from

(OFF) to (ON) at maximum intensity and viceversa.

Press the “-” key to diminish the intensity of the lateral lights

until switching them off.

Press the “+” key to increase the intensity of the lateral lights.

Resetting and configuring the saturation of the filters

signal

Switch the hood on at any speed (see paragraph above

“Selecting the suction speed (power”).

Press the "◄" key or the "►" key until seeing the symbol

relating to the “Resetting and configuration of the saturation of

the filters signal” function on the remote control.

Resetting the anti-fat filter saturation signal (GREEN LED

FLASHING on the control bar)

First proceed with the maintenance of the filter as

described in the corresponding paragraph.

Press the “+” and “-” keys contemporaneously for about 3

seconds. The LED stops flashing, indicating that the resetting

of the signal has been accomplished.

Resetting the carbon filter saturation signal (ORANGE

(amber) LED FLASHING)

Note! The reset of the carbon filter saturation signal is

normally deactivated. To activate it, see under paragraph

“Activating the carbon filter saturation signal”.

First proceed with the maintenance of the filter as

described in the corresponding paragraph.

Press the “+” and “-” keys contemporaneously for about 3

seconds. The LED stops flashing, indicating that the resetting

of the signal has been accomplished.

Deactivating the carbon filter saturation signal (for

special applications)

Switch the hood off (see paragraph above “Selecting the

suction speed (power)”).

Press the "◄" key or the "►" key until seeing the symbol

relating to the “Resetting and configuration of the filters

saturation signal” function on the remote control.

Press keys “+” and “-” contemporaneously for about 3

seconds. The LED flashes in GREEN to indicate that the

carbon filter saturation signal has been deactivated.

To reactivate the carbon filter saturation signal, repeat the

operation. The LED flashes in ORANGE.

Maintenance of the remote control

Cleaning the remote control:

Clean the remote control with a damp cloth and a neutral

solution of detergent without abrasive substances.

Changing the battery:

• Open the battery casing using a small screwdriver with a

flat point.

• Change the finished battery with a new one of 12 V type

MN21/23

In inserting the new battery respect the polarity indicated

on the battery casing!

• Close the battery casing up again.

Disposal of the batteries

Ultimate disposal of the batteries should be handled according

to all national laws and regulations. Do not place used

batteries in your regular waste.

Ultimate disposal of the batteries must be done safely.

Contact your local waste management officials for other

information regarding the environmentally sound collection,

recycling, and disposal of the batteries.

Maintenance

ATTENTION! Before performing any maintenance operation,

isolate the hood from the electrical supply by switching off at

the connector and removing the connector fuse.

Or if the appliance has been connected through a plug and

socket, then the plug must be removed from the socket.

Cleaning

The cooker hood should be cleaned regularly (at least with the

same frequency with which you carry out maintenance of the

fat filters) internally and externally. Clean using the cloth

dampened with neutral liquid detergent. Do not use abrasive

products. DO NOT USE ALCOHOL!

WARNING: Failure to carry out the basic cleaning

recommendations of the cooker hood and replacement of the

filters may cause fire risks.

Therefore, we recommend oserving these instructions.

The manufacturer declines all responsibility for any damage to

the motor or any fire damage linked to inappropriate

maintenance or failure to observe the above safety

recommendations.

Panel

Fig. 9-24

Clean the perimeter aspiration panel with the same frequency

as the ant-fats filter, using a cloth and not too concentrated

liquid detergent. Do not use abrasive substances.

Grease filter

Fig. 10-23

Traps cooking grease particles.

This must be cleaned once a month (or when the filter

saturation indication system – if envisaged on the model in

possession – indicates this necessity) using non aggressive

detergents, either by hand or in the dishwasher, which must

be set to a low temperature and a short cycle.

When washed in a dishwasher, the grease filter may discolour

slightly, but this does not affect its filtering capacity.

To remove the grease filter, pull the spring release handle.

Charcoal filter (filter version only)

Fig. 22

It absorbs unpleasant odours caused by cooking.

The saturation of the activated charcoal occurs after more or

less prolonged use, depending on the type of cooking and the

regularity of cleaning of the grease filter.

In any case it is necessary to replace the cartridge at least

every four mounths (or when the filter saturation indication

system – if envisaged on the model in possession – indicates

this necessity).

Remove the grease filters.

Fit the charcoalfilters over the motor.

Align the pins R on the cowl with the slots S, then turn the

filter clockwise until it locks in place.

Reverse the above procedure to remove the charcoal filters.

Refit the grease filters.

Replacing lamps

Fig. 28-29

Disconnect the hood from the electricity.

Warning! Prior to touching the light bulbs ensure they are

cooled down.

Replacing central lamps

1. Using a flat head screwdriver or equivalent tool, carefully

pry loose the light cover.

2. Remove the damaged light and replace with a new 12

Volt, 20 Watt (Maximum) halogen light made for a G-4

base SUITABLE FOR USE IN OPEN LUMINAIRES.

Follow package directions and do not touch new light

with bare hands.

3. Reinstall the light cover. (it will snap shut).

Replacing lateral lamps.

Replace with a new 12 Volt, 20 Watt (Maximum) halogen light

made for a G-4 base SUITABLE FOR USE IN OPEN

LUMINAIRES. Follow package directions and do not touch

new light with bare hands.

If the lights do not work, make sure that the lamps are fitted

properly into their housings before you call for technical

assistance.

Elica ALBA PYRAMID WALL Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info