212))
$&7,21
)5((=(
$&7,21
&22/
H On/OFF light
I Appliance button ON/OFF
J Temperature setting button (warmest)
K Temperature indicator
H. Light ON/OFF
I. Button ON/OFF
ON: Press the button (I). The pilot light (H)
switches on.
OFF: Keep press the button (I) until the pilot light (H)
and the temperautre indicator switched off.
K. Temperature indicator
During normal functioning the indicator shows the
warmest temperature inside the freezer.
Difference until 5°C inside the compartment are
quite normal.
Attention!
Difference between the temperature displayed and
temperature setting is normal. Especially when:
- a new setting has recently been selected
- the door has been left open for a long time
- warm food has been placed in the compartment
J - L. Temperature setting buttons
The temperature can be adjusted between -15°C
and -24°C.
By pressing the button (J or L), the current
temperature setting flashes on the indicator. It is
possible to modify the setting temperature only with
flashed indicator. To set a warmer temperature,
press button (J). To set a colder temperature, press
button (L). The indicator display the newly
selectedtemperature for a few seconds and then
shows again the inside compartment temperature.
The newly selected-temperature must be reached
after 24 hours.
Attention!
During the stability period by the first starting the
temperature displayed can not correspond to the
setting temperature. During this time it is possible
that the temperature displayed is lower than the
setting temperature.
M. Action Freeze pilot light
N. Action Freeze button
To freeze fresh foods, the “
Action Freeze
” function
must be actived. Press the super frost button
(N).The relevant pilot light (M) switches on
The function can be deactived at any time, by
pressing the button (N), otherwise it automatically
switched off. With deactived functionth pilot light (M)
switches off.
Control Panel
Use of the freezer/ appliance
L Temperature setting button (coldest)
M Action Freeze light
N Action Freeze button
O Alarm reset light
P Alarm reset button
Cleaning the interior
Before using the appliance for the first time, wash
the interior and all internal accessories with luke-
warm water and some neutral soap so as to remove
the typical smell of a brand-new product, then dry
thoroughly.
USE
Do not use detergents or abrasive
powders, as these will damage the finish.
18
23
MAINTENANCE
Periods of non-operation
When the appliance is not in use for long periods,
take the following precautions:
Turn off the appliance;
remove all food;
defrost and clean the interior and all accessories;
leave the door ajar to allow air to circulate to prevent
unpleasant smells.
Periodic cleaning
Clean the inside with warm water and bicarbonate of
soda. Rinse and dry thoroughly.
Clean the condenser (black grill) and the
compressor at the back of the appliance with a
brush or a vacuum cleaner. This operstion will
improve the performance of the appliance and save
electricity consumption.
Defrosting
Frost is automatically eliminated from the evaporator
of the refrigerator compartment every time the motor
compressor stops, during normal use. The defrost
water drains out through a trough into a special
container at the back of the appliance, over the
motor compressor, where it evaporates.
It is important to periodically clean the defrost
water drain hole in the middle of the refrigerator
compartment channel to prevent the water
overflowing and dripping onto the food inside.
Use the special cleaner provided, which you will
find already inserted into the drain hole.
The freezer compartment, however, will become
progressively covered with frost. This should be
removed with the special plastic scraper provided,
whenever the thickness of the frost exceeds 4 mm.
During this operation it is not necessary to switch off
the power supply or to remove the foodstuffs.
However, when the ice becomes very thick on the
inner liner, complete defrosting should be carried out
and it is advisable to carry out this operation when
the appliance is empty.
D037
Unplug the appliance before carrying out
any maintenance operation.
Warning
This appliance contains hydrocarbons in its cooling
unit; maintenance and recharging must therefore
only be carried out by authorized technicians.
Interior light
If it becomes necessary to replace the lamp, press
on the rear hook and at the same time
slide the cover in the direction indicated by the arrow.
Attention:
Replace the lamp with one of the same power (the
maximum power is shown on the light diffuser).
