646319
26
Verklein
Vergroot
Pagina terug
1/49
Pagina verder
26 of 49
Commissioning
Flue gas quantity and adjustment
Minimum output
Switch the boiler to commisioning
mode, while keeping flue cleaner key
(8) pressed, until the red LED (3)
starts to flash (double flash). The
display shows alternately the figures 1
and 00. With Hot Water Temperature
Adjustment (11) turned fully
clockwise, the boiler is working in
heating mode at 100% output. i.e.
maximum output
The boiler needs to be set for
operation at minimum load. Turn the
Hot water temperature adjustment
(11) anticlockwise as far as it will go
(the flow temperature of the boiler and
the figure 0 flash alternately on the
display). From this moment, the boiler
is working at minimum output.
Wait until the boiler stabilises and
then carry out the flue gas
measurement. Check the C0
2
value
at the same time by means of the
following chart.
24 HG
30 HSG/HG
C0
2
[%]
C0
2
[%]
G20 Natural gas H
9,3 -9,7
9,0 - 9,4
G31 Propane
10,9 - 11,3
10,8 - 11,2
The measurement of C0
2
values must take place with appliance casing fitted.
If values remain within the limits given
in the chart, no further regulation is
necessary.
After these measures the gas flow rate
on the counter should be checked,
taking into account the specifications
contained in the table of technical
data.
If the checks are completed, the
heating appliance must be re-set
manually to normal operation.
For this, keep the flue cleaner key
(8) pressed until the red LED (3)
goes out
If the measured values differ from the
values stated, proceed as follows:
(Numbers in the following text relate to
pictures above)
Remove the cap (2) using a
Torque T-40 bit then adjust the
Low Fire adjustment (3) on the gas
using the same T-40 bit: clockwise
to increase and anticlockwise to
decrease the C0
2
value of the
reading (because of the sensitivity
of the screw, minimum rotations
are sufficient)
Note: Because of the sensitivity of the
adjustment, minimum adjustments
should only be made, wait a few
seconds, until the C0
2
value has
stabilised, then if applicable repeat
adjustment.
After measuring, check again the
C0
2
values at High Fire. If High
fire requires any readjustment
also check and readjust Low Fire
as required.
3
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elco MHS - EURON 24 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elco MHS - EURON 24 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,98 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info