646319
15
Verklein
Vergroot
Pagina terug
1/49
Pagina verder
15 of 49
Installation
Electrical connections
General Information
Electrical installation and connection
must be carried out by an authorised
installer in accordance with applicable
National Standards, Local Standards
and Regulations.
Mains connection and Customer
wiring
The appliance is designed for
permanent connection using cables
NYM 3x1.5 mm2 or H05W-F 3 x 1
mm2. The connection cable should not
be larger than 8 mm in diameter.
Connect the mains wiring to the
respective terminals, on the Boiler
Terminal strip, in the 240V section at
the rear of the control panel. (See
picture below)
A suitable mains isolator switch must
be fitted in the power supply, to the
boiler, and sited in the boiler room.
This can be used to switch off power
to the boiler for maintenance purposes
or in the event of a problem.
Mains voltage: 230 V, 50 Hz
Mains cable Connection
All external connection cables should
be stripped to a max. 30 mm. All
external Cables entering the Boiler
must be firmly clamped in the Cable
grip after connection
The length of the cables must be
designed accordingly. Additional
cables (e.g. for system integrations),
which are attached to the terminal strip
in the boiler, must be secured along
with mains lead via the Cable grip.
When connecting the boiler, ensure
the earth cable (yellow/green), which
is longer than the supply wires (see
illustration) is connected.
Multiple plug sockets, extension cable
and adapter are not appropriate. For
earthing of the appliance under no
circumstances use the piping of the
water supply installation, heating or
gas installation.
Please note the appliance is not
protected against damage from
lightning strikes.
If the mains fuses are to be changed,
use 2A Quick Blow fuses.
Note before any connections are
made below the boiler must be
switched Off.
Remote Operation (Volt Free)
A volt free enable to the Boiler for a
Thermostat, Time switch etc, is
possible via X10-02 (2)
Remote Operation (QAA73)
Connection (1) for a QAA73 must
be via a cable with at least. 2 x 0,5
mm2.
The "Bus" cable of the QAA73
(20-30 V) must be installed and
run separately from the 230 V/50
Hz cables. The QAA73 connects
to the X10-01 connector using
screened cable.
Note: If the QAA 73 remote
control is being used, the
thermostat bridge must be
disconnected from the X10-02 (2)
connection.
Note: Only one type of Boiler
enable can be used via either
X10-01 or X10-02
Ambient / External Sensor
(QAC34)
Connect the Outside Air
Temperature sensor (3), if
required, using a Screened Cable
with at least 2 x 0,5 mm
2
, with a
maximum length of 50m.
The sensor should be positioned
on a North Facing Wall at a height
of 2 2.5 m above the floor. Under
no circumstances must it be
directly exposed to sunlight.
Connect the ambient/external
sensor to the X10-06 (3)
connector (using screened cable).
Safety Thermostat for
Underfloor Heating
Remove the bridge loop from the
terminals on the right hand side of
the Terminal Block, on the 240v
connection side, and connect the
safety thermostat for the
underfloor heating.
The Connections on the boiler
wiring side will be pre-wired back
to X3-01 on the LMU unit.
Earth Block
240v Mains Power Connection
240V Connection.
1
st
TwoTerminals
Connection for
Underfloor limit
thermostat
Cable Grip
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elco MHS - EURON 24 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elco MHS - EURON 24 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,98 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info