561014
15
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
Description of operating controls and connecting terminals
Page 15 of 24
7 SPEAKER LEVEL IN
Input jacks for connecting the ELAC subwoofer to the loudspeaker output of a power amp or surround receiver
(please see following chapter). Bass signals, that go to the LINE LEVEL IN & SPEAKER LEVEL IN are both re-
produced through the subwoofer. The SPEAKER LEVEL IN uses a floating, symmetrical circuit designed to make
the subwoofer operate like a passive loudspeaker. This way, power amplifiers with bridged (BTL) circuits can be
connected without danger. In comparison to passive loudspeakers the subwoofer input impedance is very high
(approx 100 times higher than a passive speaker). This allows parallel connection of both passive speakers and
the SUB 2040 without significantly lowering the impedance presented to the power amp or AV receiver. This also
means that large diameter cables and ‘exotic’ cables will provide little advantage due to the subwoofer’s high im-
pedance. When connecting speaker cables into the terminals provided be extremely careful to avoid touching the
cables together and causing a short circuit. Also be careful that stray speaker wire strands do not touch each oth-
er.
8 ROOM TUNING FILTER
This filter is used to optimize the bass reproduction in the room. A notch filter is used for suppressing room reso-
nances, which cause an audible bass increase at certain frequencies (e.g. "boomy" bass). By using two controls
("ROOM TUNING FREQUENCY" and "ROOM TUNING LEVEL") the frequency and damping (in decibels) can be
adjusted. For optimum adjustment a CD containing test signals would be helpful (especially sine waves in the
bass range). Best results will be gained using the ELAC Cara Test CD. To start with, set "ROOM TUNING FRE-
QUENCY" to the minimum frequency and "ROOM TUNING LEVEL" to 0 dB. The CD contains descending sine
waves from 100 Hz down to 20 Hz on separate tracks. Start by playing the highest frequency and continue on to
lower frequencies in order. There will be one frequency which seems to be much louder than the others. This will
be the room resonance. Check the CD booklet to determine the corresponding frequency. Turn the "ROOM TUN-
ING FREQUENCY" actuator to that frequency. The damping must be determined experimentally. Start at the
highest damping (-18 dB) and turn the actuator back to 0 dB step by step until the damped frequency has the
same acoustic level as all other frequencies within the room.
9 POWER SOCKET
Please insert the IEC end of the mains power lead here.
10 POWER (ON / OFF)
Once both mains and signal cables are connected, turn on the power switch. When absent for a long period, turn
off the power switch to avoid electricity consumption.
11 FUSE HOLDER
When replacing fuses, make sure to use appropriate fuses (please refer to the information given on the rear of the
speaker).
ATTENTION: Complete disconnection of the ELAC SUB 2040 subwoofer from the mains is ensured only
by pulling out the power plug. While the device is plugged in and the power switch is switched on, a static
current will flow even in standby mode (indicated by the LED glowing red).
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elac SUB 2040 ESP bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elac SUB 2040 ESP in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 1,7 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info