606110
20
Verklein
Vergroot
Pagina terug
1/100
Pagina verder
GB
- 20 -
5. Before starting the equipment
Be sure to read the following information before
you use your cordless screwdriver for the rst
time:
1. Charge the battery pack with the charger
supplied. An empty battery pack requires a
charging period of approximately 1 hour.
2. Only ever use sharp drill bits and screwdriver
bits which are suitable for the purpose and in
faultless condition.
3. Always check for concealed electric cables
and gas and water pipes when drilling and
screwing in walls.
6. Operation
6.1 Charging the battery (Fig. 2-3)
1. Remove the battery pack (5) from the handle
(Fig. 2) by pressing the pushlock buttons (8)
on the right and left side.
2. Check that your mains voltage is the same
as that marked on the rating plate. Insert the
power plug of the charger (6) into the mains
socket outlet. The green LED will then begin
to shine.
3. Push the battery pack (5) onto the battery
charger. The red LED will blink slowly and the
green LED will shine, indicating that the batte-
ry pack is being charged.
4. Both LEDs will shine when the charging is
completed.
If the green LED and the red LED shine conti-
nuously while the battery pack is inserted, the
charging temperature is either too high or too low.
- In this case, pull out the mains plug of the
charger and charge the battery in an envi-
ronment in which the temperature is either
warmer or colder.
If the red LED blinks quickly and the green LED
shines, the battery pack is too cold or too warm.
- In this case, pull out the mains plug of the
charger and store the battery in a warmer
place or let it cool down and try again.
If the fault still occurs, the battery pack is defec-
tive.
- In this case pull out the charger plug immedi-
ately and remove the defective battery pack.
- Do not use the defective battery pack again.
If the battery pack fails to become charged, ple-
ase check
whether there is voltage at the socket-outlet
whether there is proper contact at the char-
ging contacts on the charger.
If the battery still fails to become charged, please
return
the charger
the battery pack
to our Customer Service Department.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the power of the cordless equipment
drops.
6.2 Torque setting (Fig. 4 / Item 1)
Important! The tool must be at a standstill
when you set the torque with the setting ring.
The cordless hammer drill/screwdriver is tted
with a mechanical torque selector.
The torque for a speci c size of screw is selected
with the set-collar (1). The correct torque depends
on several factors:
on the type and hardness of material in ques-
tion
on the type and length screws used
on the requirements needing to be met by the
screwed joint.
The clutch disengages with a grating sound to
indicate when the set torque is reached.
6.3 Drilling/hammer drilling (Fig. 4)
For drilling purpose, adjust the torque setting
(1) to the setting “Drill”.
For hammer drilling purpose, adjust the
torque setting (1) to the setting “Hammer”.
In the drill and hammer drill settings the slip cou-
pling is non-functional. The maximum torque is
available for drilling and hammer drilling.
Anl_TE_CD_18_2_i_SPK7.indb 20Anl_TE_CD_18_2_i_SPK7.indb 20 17.12.13 10:1517.12.13 10:15
20

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Einhell TE-CD 18-2 i bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Einhell TE-CD 18-2 i in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Fins als bijlage per email.

De handleiding is 1,85 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info