605956
25
Verklein
Vergroot
Pagina terug
1/140
Pagina verder
25
GB
8. Pull the two line ends sharply to release them
from the line holders in the line spool.
9. Cut the excess line to a length of around 13cm.
This will reduce the load on the engine when
starting and warming up.
10. Refit the line spool (see section 6.1.6).
11. If you are replacing the complete line spool, skip
points 3-6.
8.2 Servicing the air filter
Soiled air filters reduce the engine output by supply
too little air to the carburetor. Regular checks are
therefore essential. The air filter (35) should be
checked after every 25 hours of use and cleaned if
necessary. If the air contains a lot of dust, the air filter
should be checked more frequently.
1. Remove the air filter cover (Fig. 10a).
2. Remove the air filter (Fig. 10b/10c)
3. Clean the air filter by tapping it or blowing it.
4. Assemble in reverse order.
Important: Never clean the air filter with petrol or
inflammable solvents.
8.3 Maintenance of the spark plug
Spark plug sparking gap = 0.6mm. Tighten the spark
plug with a torque of 12 to 15 Nm. Check the spark
plug for dirt and grime after 10 hours of operation and
if necessary clean it with a copper wire brush.
Thereafter service the spark plug after every 50 hours
of operation.
1. Dismantle the protective cap (Fig. 11a/Item 21)
using a screwdriver.
2. Pull off the spark boot plug (Fig. 11b).
3. Remove the spark plug (Fig. 11b) with the
supplied spark plug wrench (27).
4. Assemble in reverse order.
8.4 Grinding the safety hood blade
The safety hood blade can become blunt over time.
When you notice this, undo the two screws holding
the safety hood blade to the safety hood. Clamp the
blade in a vise. Sharpen the blade with a flat file and
make sure that the angle of the cutting edge is not
altered in the process. File in one direction only.
8.5 Carburetor settings
Important. Settings on the carburetor may only be
made by authorized customer service personnel.
The air filter cover must be removed before any work
on the carburetor, as shown in Figures 10a and 10c.
Setting the throttle cable
If the maximum speed of the equipment falls over
time and you have ruled out all the other causes listed
in section 11 Troubleshooting, it may be necessary to
adjust the throttle cable.
First of all check whether the carburetor opens fully
when the throttle handle is pressed fully. This is the
case if the carburetor slide (Fig. 13a) is completely
opened when the throttle is fully activated.
Figure 13a shows the correct setting. If the carburetor
slide is not completely open, it must be adjusted.
The following work is required to adjust the throttle
cable:
n Undo the lock nut (Fig. 13b/Item C) a few turns.
n Undo the adjusting screw (Fig. 13b/Item D) until
the carburetor slide is completely open when the
throttle is fully activated, as shown in Figure 13a.
n Retighten the lock nut.
Setting the idling speed
Important. Set the idling speed when the equipment
is warm.
If the engine stalls when the throttle is not pressed
and you have ruled out all the other causes listed in
section 11 Troubleshooting, the idling speed must be
adjusted. To do this turn the idling speed screw (Fig.
13b/Item E) clockwise until the equipment runs
smoothly at idling speed. If the idling speed is so fast
that the cutting tool turns as well, it has to be reduced
by turning the idling speed screw for as long as is
required for the cutting tool to stop turning as well.
8.6 Changing the oil and checking the oil level
(before using the equipment)
The motor oil is best changed when the motor is at
working temperature. In this connection, please also
read the service information.
n Keep a suitable, leak-tight receptacle within reach
when performing an oil change.
n Open the oil filler plug (Fig. 14a-14b / Item 38).
n Drain the used oil into a suitable receptacle by tilting
the engine.
n Fill in engine oil (15W40) up to the top mark (Max.)
on the oil dip stick (Fig. 14b).
n Dispose of the used oil properly by taking it to a
collection point. Most filling stations, repair garages,
and recycling centers will accept used oil free of
charge. Do not add antifreeze or transmission fluid
to the used oil. Keep used oil out of the reach of
children and away from sources of ignition.
8.7 Environmental protection
Dispose of soiled maintenance material and
operating materials at the appropriate collection point.
Recycle packaging material, metal and plastics.
Anleitung_GH_BC_33_4_S_SPK7__ 13.05.13 15:44 Seite 25
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Einhell GH-BC 33-4 S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Einhell GH-BC 33-4 S in de taal/talen: Nederlands, Duits, Engels, Frans, Portugees, Zweeds als bijlage per email.

De handleiding is 4,62 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info