448097
16
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
GB
- 16 -
(6).
Take off the guard hood (3).
Swing the depth stop (7) down and away.
While holding the spindle lock (2) pressed,
unscrew the outer flange (b) with the supplied
flange nut wrench (c).
Remove the spacer rings (d).
Remove the inner flange (e).
Thoroughly clean the spacer rings, flanges
and fastening parts.
Fit the inner flange (e).
Then fit the diamond cutting wheels together
with the spacer rings (d) to achieve the desi-
red groove width.
Important! Take account of the direction of rotati-
on when tting the diamond cutting wheels!
Important! Diamond cutting wheels must always
be replaced as pairs!
You have 6 spacer rings available, each one
being approx. 3.5mm in width. Please note
that the width of the groove is determined by
the sum of the spacer rings between the dia-
mond cutting wheels and the thickness of the
cutting wheels.
All 6 spacer rings (d) have to be fitted irres-
pective of the desired groove width.
Now re-assemble the device in reverse order,
taking care in so doing to ensure that all parts
are fitted correctly and tightly.
Important!
Only ever press the spindle lock when the
motor and grinding spindle are at a stand-
still!
You must keep the spindle lock pressed while
you change the wheel!
6.3 Motor
It is vital for the motor to be well ventilated during
operation. Be sure, therefore, to keep the ventilati-
on holes clean at all times.
6.4 Working with the masonry channel cutter
(Fig. 12)
Important! The device is tted with an overload
cut-out. The motor will cut out if overloaded. Re-
lieve the load on the motor immediately and allow
the masonry channel cutter to cool down for ap-
prox. 1 minute without load.
Important! The device is suitable for dry cutting
only!
Use a cable/pipe detector to check for conce-
aled electric cables and gas and water pipes
in the wall before you start using the masonry
channel cutter.
Select the desired groove width (see 6.2) and
groove depth (see 5.1).
Important! Only ever guide the device along the
workpiece while switched on.
Place the device against the wall with the rol-
ler (10) against the wall.
Switch on the device and then cut slowly into
the wall until the stop (7) rests against the
wall.
Now you can cut the groove in the wall. Take
care with the cutting direction (a) as you do
so. The device must always be handled on
a counterrotating basis otherwise there is a
risk that it may be forced out of the cut in an
uncontrolled manner.
Important! Cut in a straight line only. It is not pos-
sible to cut curves.
At the end of the groove, swing the device out
of the groove before you switch it off.
You can then cut out the ridge between the
two grooves with a chisel.
It is prohibited to use the machine on as-
bestos materials!
7. Replacing the power cable
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
We recommend that you clean the device
immediately each time you have finished
Anleitung_BT-MA_1300_SPK1.indb 16Anleitung_BT-MA_1300_SPK1.indb 16 25.10.11 12:5425.10.11 12:54
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Einhell BT-MA 1300 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Einhell BT-MA 1300 in de taal/talen: Engels, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 1,51 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Einhell BT-MA 1300

Einhell BT-MA 1300 Gebruiksaanwijzing - Nederlands, Deutsch, Français, Italiano, Português, Espanôl - 40 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info