Handleiding Einhell BG-EM 1030 (pagina 22 van 102) (Engels, Deens, Zweeds, Noors)

509379

Verklein

Vergroot

Pagina terug

1/102

Pagina verder

- 22 -

5. Before starting the equipment

Before you connect the equipment to the mains

supply make sure that the data on the rating plate

are identical to the mains data.

Always pull the power plug before making

adjustments to the equipment.

The lawn mower is delivered unassembled. The

complete push bar and the grass collector must

be assembled before using the lawn mower. Fol-

low the operating instructions step-by-step and

use the pictures provided as a visual guide to

easily assemble the machine.

5.1 Fitting the push bar (Fig. 3a to 3d)

Fit a bottom push bar (Fig. 3a / Item 8) into the

opening provided for it (Fig. 3a) and secure it as

shown in Fig. 3b with a screw (Fig. 3b / Item 9).

Proceed in the same way on the other side.

When you ﬁ t the top push bar you can decide the

height of the push bar by selecting the appropri-

ate fastening hole (Fig. 3c). Fasten the top push

bar using either the holes L for a low position or H

for a high position. Screw the top push bar to the

bottom push bar as shown in Fig. 3d.

5.2 Fitting the grass box (Fig. 4a to 4d)

Fit the two halves of the grass box together (Fig.

4a / Item 12). The two halves are identical. Ensure

that all the plastic lugs engage correctly. Next

push the grass box handle (Fig. 4b / Item 13) into

the openings on the grass box.

Before you ﬁ t the grass bag you must ensure that

the motor is switched oﬀ and the blade is not

rotating. The grass box must be attached to the

two hooks on the mower (Fig. 4c / Item A). To do

this, open the ejector ﬂ ap with one hand (Fig. 4d

/ Item 5) and attach the grass box with the other

hand as shown in Fig. 4d. The ejector ﬂ ap is held

against the grass box by a spring.

5.3 Fitting the wheels (5a and 5b)

Fit the four wheels (Fig. 2/Item 14) as shown

in Fig. 5a. Turn the wheel caps (Fig. 5a/Item A)

clockwise to tighten them. Fit all four wheels in the

same position (Fig. 5b).

5.4 Setting the cutting heights

Important!

Adjust the cutting height only when the engine is

switched oﬀ and the power cable has been dis-

connected.

Before you begin to mow, check to ensure that the

blade is not blunt and that none of the fasteners

are damaged. To prevent any imbalance, replace

blunt and/or damaged blades. To carry out this

check, ﬁ rst switch oﬀ the motor and pull out the

power plug.

The cutting height is adjusted as follows. Turn the

hub cap counter-clockwise to release the axle

(Fig. 5a) and remove the hub cap together with

the screw and wheel. The wheel can now be ﬁ tted

in position 1, 2 or 3 (Fig. 5b) to suit the required

cutting height. Fit all four wheels at the same

height so that the cutting blade runs parallel to

the lawn.

Position Cutting depth

1 60 mm

2 42.5 mm

3 25 mm

Power supply

The lawn mower can be connected to any light

socket-outlet with a 230 Volt alternating current.

However, the socket outlet must have an earthing

contact protected by a 16 A circuit breaker. Addi-

tionally, a residual current device (RCD) circuit-

breaker with max. 30 mA must be used!

Power cable for the device

Please only use power cables that are not dama-

ged. The total length of the power cable should

not exceed 50 meters; going beyond this distance

will reduce the power output of the electric motor.

The power cable must have a cross-section of 3

x 1.5 mm. The insulating sheath of lawn aerator

power cables is frequently damaged.

Some of the causes for this are:

•

Cuts caused by driving over the cable.

•

Pinching when the power cable is dragged

under doors and pulled through windows.

•

Cracking due to old age of the insulation.

•

Kinking by improperly fastening or guiding the

power cable.

The power cables must, at the very minimum, be

of type HO5RN-F and 3-stranded. The cable type

must be printed somewhere on the power cable.

Only purchase power cables that are marked!

Plugs and socket couplers for the power cables

must be made from rubber and splash-proof.

There is a limit to how long power cables can be.

Longer power cables require larger conductor

cross-sections. Power cables and connecting li-

Anl_BG_EM_1030_SPK1.indb 22Anl_BG_EM_1030_SPK1.indb 22 13.02.14 10:2113.02.14 10:21

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Einhell BG-EM 1030 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Einhell BG-EM 1030

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info