644136
24
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
24
41 42 43 44
Italiano English Français
ARRESTO MOTORE STOPPING THE ENGINE ARRET DU MOTEUR
ARRESTO MOTORE
Rilasciare la leva acceleratore (B, Fig. 41) portando il motore
al minimo. Spegnere il motore portando la leva starter
(C, Fig. 41) tutta verso l’alto (3). Non appoggiare la motosega
sul terreno se la catena è ancora in moto.
RODAGGIO CATENA
La regolazione deve sempre essere fatta a catena fredda.
Fare girare la catena manualmente, lubrificandola con olio
supplementare (Fig. 42). Avviare il motore per qualche
minuto a velocità moderata, controllando il regolare
funzionamento della pompa dell’olio (Fig. 43). Arrestare il
motore e regolare la tensione della catena. Avviare il motore
praticando qualche taglio in un tronco. Arrestare di nuovo
il motore e ricontrollare la tensione. Ripetere l’operazione
finchè la catena non ha raggiunto il suo massimo
allungamento. Non toccare il terreno con la catena stessa.
ATTENZIONE - Non toccare mai la catena con il
motore in moto.
STOPPING THE ENGINE
Release the throttle lever (B, Fig. 41) and let the engine
return to idle. Switch off the engine, returning the choke
lever (C, Fig. 41) to the fully up position (3). Do not put the
chain saw on the ground when the chain is still moving.
BREAKING-IN THE CHAIN
New chains will stretch and must be tightened frequently.
Tension adjustment should only be made when the chain is
cool. First, turn the chain and lubricate it with additional oil
(Fig. 42). Then start the saw and allow it to run at moderate
speed, checking that the oil pump is working properly
(Fig. 43). Stop the engine and adjust the chain tension. Start
the saw again and make a few cuts in a trunk to heat up the
chain. Stop the engine, allow the chain to cool and adjust
again. Repeat this process until the chain retains proper
tension. Do not touch the ground with the chain.
WARNING - Never touch the chain while the motor is
running.
ARRET DU MOTEUR
Lâchez le levier de l'accélérateur (B, Fig.41) et laissez le
moteur tourner au ralenti. Éteindre le moteur en amenant
le levier du starter (C, Fig. 41) en fin de course vers le haut
(3). Ne posez pas la tronçonneuse sur le terrain si la chaîne
tourne encore.
RODAGE DE CHAINE
Effectuez toujours le réglage lorsque la chaîne est froide.
Faites tourner la chaîne à la main en la lubrifiant avec de
l’huile supplémentaire (Fig.42). Mettez le moteur en marche
et faites tourner la chaîne à un régime moteur moyen en
contrôlant le bon fonctionnement de la pompe de l’huile
(Fig.43). Arrêtez le moteur, réglez la tension de la chaîne.
Redémarrez le moteur, effectuez quelques coupes sur
un tronc. Arrêtez de nouveau le moteur et recontrôlez la
tension. Recommencez l’opération jusqu’à ce que la chaîne
soit au maximum de son relâchement. Ne touchez pas le
terrain directement avec la chaîne.
ATTENTION - Ne touchez jamais á la chaîne si le
moteur tourne.
SISTEMA ANTIGHIACCIO (Fig. 44) ICE DEVICE SYSTEM (Fig. 44) SYSTEME ANTIGIVRE (Fig. 44)
Con temperature inferiori a 0°C, posizionare il cursore
(A, Fig.44A) sulla posizione invernale. In questo modo oltre
all’aria fredda viene anche aspirata aria calda proveniente
dal cilindro e quindi non si forma ghiaccio all’interno del
carburatore.
Con temperature superiori a +10°C risistemare il cursore
(A, Fig.44B) nella posizione estiva. In caso contrario si
potrebbero verificare anomalie funzionali del motore
per surriscaldamento.
In the event of temperatures below 0°C, move the cursor
(A, Fig. 44A) to the winter position. In this way heated air
from the cylinder is also taken in, preventing thus the
formation of ice inside the carburettor.
When the temperature rises above +10°C, move the
cursor (A, Fig. 44B) to the summer position. Failure to
reset this parameter could impair motor performance
due to overheating.
Avec une température inférieure à 0°C, placer le curseur
(A, Fig.44A) sur la position hiver. De cette façon, l'air froid
tout comme l'air chaud provenant du cylindre sont aspirés.
Il n'y a donc pas de formation de glace à l'intérieur du
carburateur.
Avec une température supérieure à +10°C, remettre le
curseur (A, Fig.44B) en position été. Dans le cas contraire,
le moteur pourrait présenter des dysfonctionnements
dus à une surchauffe.
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Efco MT7200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Efco MT7200 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 1,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info