644134
24
Verklein
Vergroot
Pagina terug
1/68
Pagina verder
41 42 43 44
Italiano
ARRESTO MOTORE
ARRESTO MOTORE
Rilasciare la leva acceleratore (B, Fig. 41) portando il motore
al minimo.
Spegnere il motore portando la leva starter (C, Fig. 41) tutta
verso l’alto (3). Non appoggiare la motosega sul terreno se
la catena è ancora in moto.
RODAGGIO CATENA
La regolazione deve sempre essere fatta a catena fredda
.
Fare girare la catena manualmente, lubrificandola con oli
o
supplementare (Fig. 42). Avviare il motore per qualche
minuto a velocità moderata, controllando il regolare
funzionamento della pompa dell’olio (Fig. 43). Arrestare i
l
motore e regolare la tensione della catena. Avviare il motore
praticando qualche taglio in un tronco. Arrestare di nuovo i
l
motore e ricontrollare la tensione. Ripetere l’operazione
finché la catena non ha raggiunto il suo massim
o
allungamento. Non toccare il terreno con la catena stessa.
ATTENZIONE - Non toccare mai la catena con il
motore in moto.
SISTEMA ANTIGHIACCIO
Con temperature inferiori a 0°C, posizionare il
cursore (A, Fig.44) sulla posizione invernale. In
questo modo oltre all’aria fredda viene anche
aspirata aria calda proveniente dal cilindro e quindi
non si forma ghiaccio all’interno del carburatore.
Con temperature superiori a +10°C risistemare il
cursore (A, Fig.45) nella posizione estiva. In caso
contrario si potrebbero verificare anomalie
funzionali del motore per surriscaldamento.
English
STOPPING THE ENGINE
STOPPING THE ENGINE
Release the throttle lever (B, Fig. 41) and let the engine
return to idle.
Switch off the engine, returning the choke lever (C, Fig. 41)
to the fully up position (3). Do not put the chainsaw on the
ground when the chain is still moving.
BREAKING-IN THE CHAIN
New chains will stretch and must be tightened frequently
.
Tension ad
j
ustment should only be made when the chain is
cool. First, turn the chain and lubricate it with additional oi
l
(Fig. 42). Then start the saw and allow it to run at moderate
speed, checking that the oil pump is working properly (Fig
.
43). Stop the engine and ad
j
ust the chain tension. Start the
saw again and make a few cuts in a trunk to heat up the
chain. Stop the engine, allow the chain to cool and ad
j
ust
again. Repeat this process until the chain retains proper
tension. Do not touch the ground with the chain.
WARNING - Never touch the chain while the motor is
runnin
g
.
ICE DEVICE SYSTEM
In the event of temperatures below 0°C,movethe
cursor (A, Fig. 44) to the winter position. In this way
heated air from the cylinder is also taken in,
preventing thus the formation of ice inside the
carburettor.
When the temperature rises above +10°C, move
the cursor (A, Fig. 45) to the summer position.
Failure to reset this parameter could impair motor
performance due to overheatin
g
.
Français
ARRET DU MOTEUR
ARRET DU MOTEUR
Lâchez le levier de l'accélérateur (B, Fig.41) et laissez le
moteur tourner au ralenti.
Éteindre le moteur en amenant le levier du starter (C, Fig. 41)
en fin de course vers le haut (3). Ne posez pas la
tronçonneuse sur le terrain si la cha
î
ne tourne encore.
RODAGE DE CHAINE
Effectuez tou
j
ours le réglage lorsque la cha
î
ne est froide.
Faites tourner la cha
î
neàlamainenlalubrifiantavecde
l’huile supplémentaire (Fig.42). Mettez le moteur en marche e
t
faites tourner la cha
î
ne à un régime moteur moyen en
contrôlant le bon fonctionnement de la pompe de l’huile
(Fig.43).Arrêtezlemoteur,réglezlatensiondelacha
î
ne.
Redémarrez le moteur, effectuez quelques coupes sur un
tronc. Arrêtez de nouveau le moteur et recontrôlez la tension.
Recommencez l’opération
j
usqu’à ce que la cha
î
ne soit au
maximum de son relâchement. Ne touchez pas le terrain
directement avec la cha
î
ne.
ATTENTION - Ne touchez
j
amais á la chaîne si le
moteur tourne.
SYSTEME ANTIGIVRE
Avec une température inférieure à 0°C,placerle
curseur (A, Fig.44) sur la position hiver. De cette
façon, l'air froid tout comme l'air chaud provenant
du cylindre sont aspirés. Il n'y a donc pas de
formation de glace à l'intérieur du carburateur.
Avec une température supérieure à +10°C,
remettre le curseur (A, Fig.45) en position été.
Dans le cas contraire, le moteur pourrait présenter
des d
y
sfonctionnements dus à une surchauffe.
24
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Efco MT6500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Efco MT6500 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 4,2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info