644116
38
Verklein
Vergroot
Pagina terug
1/68
Pagina verder
38
Italiano FrançaisEnglish
USE
UTILISATION
UTILIZZO
59
60
Cercare di procedere in maniera ritmica. Rimanere saldamente
fermi con le gambe leggermente divaricate. Avanzare al termine
della corsa di ritorno e rimanere di nuovo saldamente fermi.
Lasciare che la coppa di supporto sfiori il terreno. Serve a
evitare che il disco tocchi il terreno.
Per ridurre il rischio di attorcigliamento di materiale intorno
al disco, attenersi alle seguenti istruzioni:
1. Tagliare sempre con il motore a pieno regime.
2. Evitare il materiale precedentemente tagliato durante la corsa
di ritorno.
Arrestare il motore, sganciare il cinghiaggio e appoggiare l’unità
a terra prima di iniziare a raccogliere il materiale tagliato.
Taglio di erba con testina a fili di nylon
AVVISO: Non utilizzare un filo più lungo del diametro
specificato. Con la protezione montata correttamente,
l’apparato di taglio incorporato regola automaticamente la
lunghezza appropriata del filo. L’uso di fili eccessivamente
lunghi può sovraccaricare il motore e causare danni al
meccanismo di frizione e alle parti adiacenti.
Rifinitura
Tenere la testina inclinata appena sopra il terreno. Il taglio
viene eseguito dall’estremità del filo. Lasciare agire il filo. Non
spingere mai il filo nell’area da tagliare (Fig.59).
• Il filo consente di rimuovere facilmente erba ed erbacce
alla base di muri, staccionate, alberi e cordoli; tuttavia, può
danneggiare la corteccia di certi alberi e arbusti e intaccare i
pali delle staccionate.
Per ridurre il rischio di danneggiare altre piante, accorciare il
filo a 10-12 cm e diminuire la velocità del motore.
• Dans la mesure du possible, travaillez de façon rythmée.
Tenez-vous sur vos deux pieds, le poids également réparti.
Avancez après le retour de coupe et tenez-vous de nouveau
fermement sur vos deux jambes.
Laissez le carter reposer légèrement sur le sol. Il est sert à
protéger la lame de tout contact avec le sol.
Pour réduire le risque d’enroulement de débris autour de la
lame, suivez les instructions ci-dessous :
1. Coupez toujours à la puissance maximum.
2. Évitez le contact avec l’herbe déjà coupée au retour de coupe.
Arrêtez le moteur, détachez le harnais et posez la machine sur
le sol avant de procéder au ramassage de l’herbe coupée.
Coupe d’herbe à l’aide d’une tête à fils
ATTENTION : La longueur du fil de coupe ne doit pas
excéder le diamètre de coupe prévu. Une fois la protection
appropriée montée, le dispositif de coupe règlera
automatiquement le fil à la longueur appropriée. L’utilisation
d’un fil trop long peut entraîner la surcharge du moteur et
endommager le mécanisme d’embrayage, ainsi que les pièces
à proximité.
Coupe avec une tête à fils
Maintenez la tête de coupe à fils juste au-dessus du sol, à partir
d’un angle. L’extrémité du fil effectue tout le travail de coupe.
Laissez le fil travailler à son rythme. N’appuyez jamais le fil
dans la zone de coupe (Fig.59).
Le fil permet de couper l’herbe et les mauvaises herbes qui
poussent au bord des murs, des clôtures, des arbres et des
bordures. Toutefois, il peut également endommager l’écorce
des arbres et les buissons ou encore les montants de clôtures.
Pour éviter d’endommager les plantes, raccourcissez le fil
jusqu’à 10 à 12 cm et réduisez le régime du moteur.
• Try to work rhythmically. Stand firmly with your feet apart.
Move forward after the return stroke and stand firmly again.
• Let the support cup rest lightly against the ground. It is used
to protect the blade from hitting the ground.
Reduce the riNL of material wrapping around the blade by
following these instructions:
1. Always work at full throttle.
2. Avoid the previously cut material during the return stroke.
Stop the engine, unclip the harness and place the machine on
the ground before you start to collect the cut material.
Grass trimming with a trimmer head
CAUTION: Do not work with mowing line longer than
the intended diameter. With a properly mounted guard, the
built-in cutter will automatically adjust the line to its proper
length. Overly long lines can overload the engine, resulting
in damage to the clutch mechanism and nearby parts.
Trimming
• Hold the trimmer head just above the ground at an angle. It
is the end of the cord that does the work. Let the cord work
at its own pace. Never press the cord into the area to be cut
(Fig.59).
The cord can easily remove grass and weeds up against walls,
fences, trees and borders, however it can also damage sensitive
bark on trees and bushes, and damage fence posts.
Reduce the riNL of damaging plants by shortening the cord
to 10-12 cm and reducing the engine speed.
38

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Efco DS2800 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Efco DS2800 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 1,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info