516208
7
Verklein
Vergroot
Pagina terug
1/91
Pagina verder
Wireless Print Server
Users Manual
Version: 1.0(July, 2005)
COPYRIGHT
Copyright 2005/2006 by Edimax Technology. All rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or
translated into any language or computer language, in any form or by any means,
electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior
written permission of this company.
Federal Communication Commission
Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
This equipment must be installed and operated in accordance with provided instructions
and a minimum 20 cm spacing must be provided between computer mounted antenna and
persons body (excluding extremities of hands, wrist and feet) during wireless modes of
operation.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the authority to operate equipment.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled
environment. In order to avoid the possibility of exceeding the FCC radio frequency
exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches)
during normal operation.
The antenna(s) used for this transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE
EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment
and telecommunication terminal Equipment and the mutual recognition of their conformity
(R&TTE)
The R&TTE Directive repeals and replaces in the directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of
April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use
it. However, special attention must be paid to the dangers of electric shock and static
electricity when working with electrical equipment. All guidelines of this and of the
computer manufacture must therefore be allowed at all times to ensure the safe use of the
equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria, Belgium,
Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg, the Netherlands,
Portugal, Spain, Sweden, and the United Kingdom.
The ETSI version of this device is also authorized for use in EFTA member states: Iceland,
Liechtenstein, Norway, and Switzerland.
EU Countries Not intended for use
None.
DISCLAIMER
This company makes no representations or warranties, either expressed or implied, with
respect to the contents hereof and specifically disclaims any warranties, merchantability or
fitness for any particular purpose. Any software described in this manual is sold or
licensed "as is". Should the programs prove defective following their purchase, the buyer
(and not this company, its distributor, or its dealer) assumes the entire cost of all
necessary servicing, repair, and any incidental or consequential damages resulting from
any defect in the software. Further, this company reserves the right to revise this
publication and to make changes from time to time in the contents hereof without
obligation to notify any person of such revision or changes.
Contents
1. PRODUCT INTRODUCTION 1.1 PRODUCT
INTRODUCTION.....................................................................1
1.3 Network Printing Architecture..............................................2
Print Server Network Functions...............................................................2
Network Printing Functions for Clients....................................................3
Network Printing Functions for Network Server......................................5
1.4 Network Printing Environment.............................................6
1.6 Firmware & Printing Function...............................................8
3. WINDOWS PEER-TO-PEER NETWORK 3.1 SYSTEM
ARCHITECTURE....................................................................9
3.2 Administrator Installation and Setup..................................10
3.4 Client Installation and Setup..............................................16
3.5 Client Utilities.....................................................................20
3.5.1 Network Ports Quick Setup.......................................................20
3.5.2 Remote Ports (Utility)..................................................................21
3.6 Windows Add Printer Procedure.....................................24
4. WINDOWS NT/2000/2003 NETWORK 4.1 SYSTEM
ARCHITECTURE..................................................................28
4.2 Windows NT/2000/2003 Server Installation and Setup.....29
4.3 User Installation and Setup................................................30
5. NETWARE NETWORK 5.1 SYSTEM
ARCHITECTURE..................................................................31
5.2.1 Installation Using PCONSOLE....................................................32
6. UNIX SYSTEM NETWORK 6.1 INTRODUCTION...35
6.3.1 DHCP..........................................................................................36
6.3.2 BOOTP........................................................................................36
7. CONFIGURATION UTILITY 7.1 INTRODUCTION.39
7.3 Status of Print Server.........................................................41
7.4 Setup the Print Server........................................................42
7.5 AppleTalk Configuration.....................................................43
7.6 General Configuration........................................................44
7.7 Netware Print Server Configuration...................................45
7.8 System Configuration.........................................................46
7.9 TCP/IP Configuration.........................................................48
7.10 Wireless Configuration.....................................................50
7.11 SNMP Configuration........................................................57
8. WEB MANAGEMENT 8.1 INTRODUCTION.....62
8.3 Device Status.....................................................................63
8.3.1 System.........................................................................................63
8.3.2 Printer.........................................................................................63
8.3.3 TCP/IP........................................................................................64
8.3.4 SMB...........................................................................................64
8.3.5 SNMP.........................................................................................65
8.3.6 NetWare......................................................................................65
8.3.7 AppleTalk...................................................................................66
8.4.1 System......................................................................................66
8.4.1.1 Advanced Settings.....................................................................67
8.4.2 Wireless Setting..........................................................................67
8.4.2.1 General Setting.........................................................................68
8.4.2.2 Encryption...............................................................................69
8.4.2.3 Site Survey..............................................................................72
8.4.3 TCP/IP.......................................................................................73
8.4.4 SMB.........................................................................................74
8.4.5 SNMP.......................................................................................74
8.4.6 NetWare....................................................................................75
8.4.7 AppleTalk.................................................................................76
8.4.8 Save Settings.............................................................................77
8.5 System Tools..................................................................78
8.5.1 Load Default.............................................................................78
8.5.2 Upgrade Firmware from Browser..............................................78
9.2 System Setup....................................................................80
9.2.1 Print Server Side.......................................................................80
9.2.2 Client Side................................................................................80
10. WINDOWS XP SP2 SETUP...........................................83
1
1. Product Introduction
1.1 Product Introduction
Thank you for purchasing and using our print server. This
print server allows your printer to become a shared device
on the network. It offers printing flexibility and
manageability on your Local Area Network at an extremely
low cost and with an absolute minimum setup and
maintenance required.
This print server provides IEEE 802.11g/b wireless LAN (up
to 54Mbps data transfer rate), an Ethernet network port
(10/100Mbps Ethernet) and one print port for printer.
This print server supports IPX/SPX, NetBEUI, TCP/IP and
AppleTalk protocols. It is the best network printing
solutions for various common network operating systems
such as Windows 95/98/Me/NT/2000/XP/2003, NetWare,
Unix/Linux and MAC OS, etc.
With the help of Installation Wizard, you can easily and
instantly complete the settings for the printing environment,
and start enjoying the fantastic features provided by the
print server.
In the following chapters, we will introduce in detail the
printing features, installation methods, and system
configuration for different network environments.
If you would like to set up and install print server quickly,
please refer to the Quick Installation Guide that comes
along with this print server.
1.2 Product Package
This package contains the following components:
l One Print Server
l One Antenna
l One Power Adapter
l One Quick Installation Guide
l One CD-ROM (Including all the software utilities, drivers and Users Manual)
2
1.3 Network Printing Architecture
This section illustrates how print server functions and
operates on the network. Before you install and use print
server, it is strongly recommended that you read this
section completely, and select only the chapters you need
according to your network operating system by Contents of
the Users Manual in next section.
This section will first introduce the role every component
plays in the network-printing environment.
Print Server
Client User
Network Server (optional)
Windows NT Server
NetWare Server
Windows 98Windows NT
Workstation
Windows 2000
Unix Print Server
Network Printing Environment
Print Server
Client User
Network Server
Print Server Network Functions
Windows NT Server
NetWare Server
Windows 98Windows NT
Workstation
Windows 2000
Unix Print Server
Print Server
Because print server supports IPX/SPX, NetBEUI, TCP/IP
and AppleTalk network protocols, any networked computer
3
can directly print to the print server from any of its installed
protocol.
Network Printing Functions for Clients
Windows NT Server
NetWare Server
Windows 98Windows NT
Workstation
Windows 2000
Unix Print Server
Client User
Common operating systems for clients are classified as
following:
Windows 95/98/Me/NT/2000/XP/2003
Our print server system provides PTPP (Peer-to-Peer
Printing) driver and utilities for Windows
95/98/Me/NT/2000/XP/2003 users. PTPP (Peer-to-Peer
Printing) supports TCP/IP protocol.
4
In the client installation procedure, after PTPP (Peer-to-
Peer Printing Driver) is installed into Windows, the system
will automatically (manual configuration is also allowed)
search all the print servers on the network, and then add
their printing ports into Windows printing port (see below).
Windows 98
PTPP
Print Server
MIS-2
P1
P2
P3
P1
Print Server
MIS-1
UNIX / Linux
UNIX (include HP/UX, SCO Unix, SunOS, Solaris, Unixware
DECUnix, IBM AIX and others) and Linux use the system-
standard LPR to print through print server.
MAC OS
MAC OS can use the system-standard AppleTalk network to
print through print server.
5
Network Printing Functions for Network Server
Windows NT Server
NetWare Server
Windows 98Windows NT
Workstation
Windows 2000
Unix Print Server
Network Server
Common network servers are classified as following:
Windows NT/2000/2003
Our print server system provides PTPP (Peer-to-Peer
Printing) driver and utilities for Windows NT/2000/2003.
After PTPP is installed, the server can directly print through
print server. Adding this printing function into Windows
NT/2000/2003 Server allows print queue, user authority
management, and many other advanced features to be
used.
NetWare 3.x/4.x/5.x
In NetWare environment, print server offers various printing
modes like print queue, remote printer, etc.
6
1.4 Network Printing Environment
Common network environment are classified as following:
Windows Peer-to-Peer Network
The clients PTPP driver will use TCP/IP protocol to print
through print server.
Windows NT/2000/2003 Network
Network printing function will become available after PTPP
driver is installed into Windows NT/2000/2003. Adding this
printing function into Windows NT/2000/2003 Server allows
print queue, user authority management, and many other
advanced features to be used.
NetWare Network (see below)
7
1.5 Contents of the Users Manual
Chapter 2 explains print servers hardware installation and
configuration. It is strongly recommended for you to read.
The following chapters introduce:
Chapter 3. Windows Peer-to-Peer Network
Chapter 4. Windows NT/2000/2003 Server-Based Network
Chapter 5. NetWare Network
Chapter 6. UNIX System Network
You may select the appropriate chapters and sections to
read depending on your network printings requirement.
Chapter 7 and chapter 8 introduce print servers
management and configuration utilities on Windows and
Web Browsers environment respectively. You may select
the appropriate management utility according to the
administrators computer platform.
Chapter 9 introduces Print Servers IPP Printing function
and setup procedure. The IPP Printing provides a
convenient way to print documents across the Internet by
the IPP protocol.
Chapter 10 introduces how to deal with the problem that if
you cant find any print server listed on the Available
Ports in Network Ports Quick Setup in Windows XP SP2.
8
1.6 Firmware & Printing Function
The print server provides a complete network printing
solution. The feature set is listed below:
PTPP (Peer-to-Peer-Printing)
TCP/IP (LPR)
IPP Printing
NetWare Bindery Printing
AppleTalk
SMB Printing
2. Hardware Installation
Unpack the print server package and verify that all the
items listed in the section 1.2 are provided.
Connect the print server to the printer you want to share on
the network.
Connect the print server to your network by attached the
network cable to the UTP port of the print server.
Connect the power adapter to the print server. The print
server will perform the Power-On-Self-Test (POST) after it
is powered on. During the POST, the Status and Ready
LEDs will be on. When the LEDs are unlighted, the print
server is ready.
NOTE1: MUST use the power adapter shipped with the print server, do
NOT use any other power adapter from any sources.
NOTE2: To prevent the compatibility problem between print server and
a few printer, it is recommended that you power on the print
server before the printer.
9
3. Windows Peer-to-Peer Network
3.1 System Architecture
Print server supports Windows Peer-to-Peer network
printing mode, which is suitable for most medium and small
network environments. Through quick and simple
installation procedure, users can immediately enjoy the
convenience of network printing.
Installation procedure is separated into following two parts:
1. Administrator Installation and Setup (refer to section 2
for more detailed information).
System administrators must:
Install administrators utilities into his/her computer.
Configure print server from administrators configuration
utility.
2. Client Installation and Configuration (refer to section 3
for more detailed information).
Client users must install Windows PTPP driver (Peer-to-
Peer Printing) for network printing.
In addition, after PTPP is installed, the system will
automatically search for all print servers on the network,
and add the printing port of the print servers into Windows
printing port (refer to Network Printing Architecture in
section 1.4 for more detailed information).
10
3.2 Administrator Installation and Setup
The Administrator Installation can be performed on
Windows 95/98/Me/NT/2000/XP/2003 with the same user
interface. Before the installation, please verify that your
network protocol is installed on your PC (TCP/IP, IPX
and/or NetBEUI).
Insert the CD shipped along with the print server into your
CD-ROM drive. The Autorun.exe program should be
executed automatically. If not, run Autorun.exe manually
from CD-ROM drives root directory.
The Installation Manager will be displayed on the screen
as following. Click Admin Utility then click English
Version .
11
The Utilities Setup window will be displayed. Click Next.
Click Next to install the utilities in the default folder or
click Browse to specify the destination folder where you
would like to install the utilities.
Select the components you want to install. It is highly
recommended to install all provided components. Click
Next to continue.
Specify the program folder where the program icons will be
added to, click Next
12
.
The system will start to install the utilities automatically.
13
You have completed the installation phase and prepare to
configure the Print Server. The Choose Print Server will
list all Print Servers within the network. Select the Print
Server you would like to configure and click Next.
NOTE 1: If this is the first time you configure the Print Server, the Print Server
Name is the last 6-digit of MAC ID with prefix PS. Please check
the MAC ID on the print server.
NOTE 2: The list can only display the devices from the same manufacturer.
Specify a recognizable name for the Print Server and click
Next.
14
Specify the IP Address for the Print Server manually or
click Next to keep default IP Address, i.e. 192.168.2.2.
The configuration summary is displayed in the window. Now,
you have completed the Print Server Setup. Click Finish
and your system will add network port of the Print Server to
your PC automatically.
The Administrator Installation procedure is totally
completed. Click Finish.
15
The Administrator Installation Program have executed the
installation procedure that performs the following tasks:
Install all utilities and drivers to the administrators PC.
Configure the print server (including the print server name
and network protocol)
Add the network port of the print server to the
administrators PC.
If you want to print from this administrators PC to the print
server, all you need to do is to perform Windows standard
Add Printer procedure (please refer to Section 3.6).
3.3 Administrator Utilities
After Administrator Installation is completed, there will be
four utilities in print servers program folder.
.
16
3.4 Client Installation and Setup
The Client Installation can be performed on Windows
95/98/Me/NT/2000/XP/2003 with the same user interface.
Before the installation procedure, please confirm that your
PC has connected to the network and installed at least one
network protocol.
Insert the CD shipped along with the print server into your
CD-ROM drive. The Autorun.exe program should be
executed automatically. If not, run Autorun.exe manually
from CD-ROM drives root directory.
The "Installation Manager" will be displayed on the screen
as follows. Click Client Utility then click English Version.
The Utilities Setup window will be displayed. Click Next.
17
Click Next to install the utilities in the default folder or
click Browse to specify the destination folder where you
would like to install the utilities.
Specify the program folder where the program icons will be
added to, click Next.
The system will start to install the utilities automatically.
18
Now, the installation procedure is completed, you are ready
to set up the clients computer. All network ports of the
Print Servers detected on the network will be added to your
PC automatically, click Continue.
The Client Installation procedure is completed. Click
Finish.
19
After the installation, you have completed the following
tasks:
Install all utilities and drivers to the clients PC.
Add all the print servers network ports of the network to
the clients PC.
You can then perform the Windows standard Add Printer
procedure to add network printers to your PC. Please refer
to Section 3.6.
20
3.5 Client Utilities
After Client Installation is completed, there will be three
tools in print servers Program folder.
l Network Ports Quick Setup
l Remote Ports
l Uninstall Network Driver
3.5.1 Network Ports Quick Setup
Network Ports Quick Setup Utility offers a very simple
method to add or remove print servers printer port from the
clients computer.
During the clients installation procedure, the system will
automatically search for all print servers on the network,
and add them into the printer ports of the clients computer
21
If you have just installed another new print server in the
network, you must run this program first. This program will
search for new print servers and allow you to add the new
network printer port into clients computer conveniently.
Perform the standard Add Printer procedure, then you can
print directly to the printer through the newly installed print
server.
Please be aware that Network Ports Quick Setup Utility can
only detect and configure all print servers on the same
network, it cannot search and configure print servers on
other subnets across network segments. You must use
Remote Ports Utility described in the next section to
manage remote (across network segments) print servers.
3.5.2 Remote Ports (Utility)
Remote Ports Utility offers a convenient way for you to
manage and add printer port of the remote print server.
From the assistant of this utility, you can print to other print
servers outside the subnet across network segment.
However, please note that this function only supports
TCP/IP network protocol.
Please follow the procedures described below:
Step1. Run Remote Ports Utility. Clicks Add to add a
remote print port.
22
Step2. Enter print servers name, IP address, select used
ports, and enter LPR queue name of each port. Click Ok.
Step3. The new remote print port is displayed as follows.
In order to use the remote printing function, you will have to
proceed with normal Add Printer procedure and select your
printer port as the newly added remote printer port.
23
24
3.6 Windows Add Printer Procedure
After adding a Network Port of the print server to your PC
by Administrator or Client Installation Program, you can
follow the procedure described below to add printer to the
Windows. Note that following Add Printer steps are
running in Windows XP, the steps in other Operating
Systems are similar.
Step1. Click Start, choose Settings and select Printers
and Faxes.
Step2. Click Add a Printer.
Step3. The Add Printer Wizard is displayed. Click Next.
Step4. Select Local printer attached to this computer
and make sure that Automatically detect and install my
Plug and Play printer is not selected. Click Next.
25
Step5. Choose the suitable Print Server Network Port
which was created by the Administrator Installation or
Client Installation process and click Next.
Step6. Select a suitable printer manufacturer and the
printer model and click Next. If your printer is not in the
list, click Have Disk…” to install the driver of the printer.
After installation, the printer model will be added to the list.
26
Step7. Name your printer and setup the default printer,
click Next.
Step8. Choose to print the test page or not. It is
recommended to print a test page. Click Next.
27
Step9. You have added the printer to the PC successfully.
The information of the printer is displayed in the windows.
Click Finish.
28
4. Windows NT/2000/2003 Network
4.1 System Architecture
In Windows network environment, other than the Peer-to-
Peer network printing architecture described in the previous
chapter, we also offer the Server-Based Printing
architecture for Windows NT/2000/2003 server. Only one
Windows NT/2000/2003 is required to have Windows PTPP
(Peer-to-Peer Printing) driver installed and share the
printing service on the network. Other network users can
simply connect to the server and access the shared printer
(see below).
29
4.2 Windows NT/2000/2003 Server Installation and
Setup
Please follow the procedures described below for
installation and construct a peer-to-peer connection (PTPP)
between Windows NT/2000/2003 Server and Print Server.
Step1.
If this is your first time installing print server, please install
the administrator software on Windows NT/2000/2003
server first. Refer to section 3.2 for installation instructions.
If your network has already installed a working print server
and your Windows NT/2000/2003 server has not yet
installed the PTPP driver, please install the client software.
Refer to section 3.4 and 3.5 for installation instructions.
Step2.
Please add/configure the Peer-to-Peer Printing of the
Windows NT/2000/2003 network printer and verify that you
can print from Windows NT/2000/2003 to the print server by
the installed PTPP driver.
Step3.
Share the above servers printer to the network by
performing the standard Windows printer sharing process.
30
4.3 User Installation and Setup
After server sides installation is completed, client side will
be able to find the servers shared printer in Network
Neighborhood. You only need to perform Windows
standard Add New Printer procedure, select Network
Printer shown in the screen below, and complete the
configurations afterwards to access the shared printer.
31
5. NetWare Network
5.1 System Architecture
We implement NetWare printer sharing functionality into the
print server itself, thus allowing one or more printers
attached by a print server to be connected to the network.
We have developed the print server to support NetWare
print server.
Embedded print server, which emulates the queue
management functionality of NetWare print server,
PSERVER program running on the NetWare server. A user
first prints a job at a workstation, the job is routed to a
NetWare server, the NetWare server stores the job in a
print queue and then the print server gets the print job from
the queue to printers.
Netware Server
Windows 98
Windows 2000
Print Queue
Print Server
Compare with NetWare printing functionality, the
advantages of embedding the NetWare network printing
functionality in the print server include:
Installation is easier and quicker.
Network management is easier.
Printing performance is enhanced.
Relieve NetWare file servers burden.
Relieve the need of a workstation running the remote
printer utility.
32
Improve productivity by locating the printer near the
workgroup.
Each print server should log into a NetWare server before
servicing the print jobs. Each print server will occupy a user
account with which it can log into the NetWare server.
5.2 NetWare 3.x/4.x/5.x Installation & Setup
Once your print server is connected to your Ethernet
network, you can set it up for use with your networking
software.
5.2.1 Installation Using PCONSOLE
5.2.1.1 Configuring as Print Server Mode
1. Run the NetWare PCONSOLE program.
2. Change the current file server, if necessary, using the
Change Current File Server menu selection.
3. Choose the Print Queue Information menu selection.
4. Press the Insert key to add a new print queue.
5. Type in a print queue name, such as PQ or Q1.
6. You have now successfully created the print queue that
your print server will serve. Press the Escape key until the
Available Options main menu is displayed.
7. Select Print Server Information.
8. Press the Insert key to add a new NetWare print server
object. The print server name can be identical to the
PSxxxxxx name printed on the label of the print server.
33
9. Press Enter to select the newly created print server.
10. Select Print Server Configuration.
11. Select Printer Configuration.
12. Select Printer 0 (or Printer 1, Printer 2), and press
Enter, then select LPT1 (or LPT2, LPT3) in the Type field.
If your print server is with only one port, you do not need to
configure this Type field.
13. Press Escape, and answer Yes to the Save Changes
question.
14. Select Queues Serviced by Printer, then select Printer
0 (or Printer 1, Printer 2) and press Enter.
15. Press Insert and add your newly created print queue to
the list of queues serviced by the printer. Enter a priority
34
number for the queue service, or press Enter to accept the
default.
16. Repeatedly press Escape to exit the PCONSOLE
program.
17. Reset the print server to have the changes take effect.
NOTE: If the print server you have is with multiple printer
connectors, you may create multiple print queues and
printer objects.
Your print server should now be ready to use. You should
be able to redirect printing to your print server using a
CAPTURE command such as the one shown in the previous
section.
35
6. UNIX System Network
6.1 Introduction
The print server is available for TCP/IP printing by Unix
LPD (Line Printer Daemon) protocol. The LPD protocol
originated with Unix release is based on the BSD version of
Unix and supported under most versions of Unix.
This chapter explains how to configure the print server for
TCP/IP operation, and how to modify configuration files on
your Unix system to allow printing to the print server. The
configuration examples in this manual follow the syntax for
BSD based Unix systems. Please refer to the related
system documentation for the correct syntax of your
systems.
To configure the print server for LPD printing, perform the
procedures below:
1. Enable Print Servers TCP/IP Support.
2. Set up Print Servers IP address.
3. Verify Print Servers IP Address.
4. Configure remote LPD printing on the host.
5. Print a test page.
In the next sections, we will describe these five procedures
step by step.
6.2 Enable Print Servers TCP/IP Support
The default configuration of the print server is with TCP/IP
support enabled. Anyway, you can configure the print
server to enable TCP/IP support using the configuration
program.
6.3 Setup Print Servers IP Address
The print server must have a unique IP address in order to
be recognized by the network.
You can set up the IP address on the various Unix systems
using any one of the following methods:
1. DHCP (Dynamic Host Configuration Protocol)
2. BOOTP (Bootstrap Protocol)
36
The print server will use the last three methods to obtain its
IP address automatically if its IP address is configured as
Auto (0.0.0.0).
6.3.1 DHCP
There are many Unix systems that support DHCP protocol, and the
procedures to configure the DHCP server database are different. This
manual does not describe the DHCP server configuration on the Unix
systems. It is highly recommended that the DHCP server should be located
on the same network as the print server.
6.3.2 BOOTP
If you have the BOOTP daemon, bootpd, running on your UNIX system that
is accessible by the print server, you can use the BOOTP protocol to set up
the IP address of the print server. We recommend that the BOOTP server
should be located on the same subnet as the print server. If you use
Network Information Services (NIS) in your system, you may need to rebuild
the NIS map with the BOOTP services before doing the following BOOTP
configuration. To rebuild the NIS map, please refer to your system
documentation.
To configure the IP address data for the BOOTP server, you will need to log
in the host of BOOTP server as the superuser (root). Perform the following
steps to add address entries,
1. Optionally, assign a name corresponding to the print
servers IP address. You can add this address to the
/etc/hosts file, by adding a line such as:
203.66.191.12 pserver
2. Add an entry to the hosts /etc/bootptab file, similar to
the following:
hostname:\
:ht=1:\
:ha=print_server_ethernet_address:\
:ip=print_server_ip_address:
Lines should be indented with tabs.
Where hostname is the device name of a print server, the ht=1 tag specifies
the hardware type is Ethernet, the ha= tag specifies the Ethernet address of
a print server, which is the Node ID located on the print server. The ha tag
37
must be preceded by the ht tag. The ip= tag should correspond to the IP
address you want to assign to the print server.
For example, a print server with the following configuration:
Node ID: 0000B4010101 (this implies Ethernet
address is 0000B4010101),
IP address: 203.66.191.12
The entry for this print server in the /etc/bootptab file should be:
PS010101:\
:ht=1:\
:ha=0000B4010101:\
:ip=203.66.191.12:
6.4 Verify Print Servers IP Address
To verify that your print server is responding to the newly
assigned IP address using a PING command:
ping ip-address
6.5 Configure Remote LPD Printing on the Host
The procedure you use to configure your Unix host(s) to
allow printing to your network remote print server varies
between different varieties of Unix. The procedure below
can be used for Unix variants that are related to BSD Unix,
such as SunOS or Linux. For other versions of Unix,
consult your system documentation, keeping in mind that:
1. The print server should be treated as a BSD networked
print server host.
2. The host name should be the name (or IP address) that
you have assigned to the print server.
3. The printer name (or queue name) on the remote host
should be lpt1, lpt2 or lpt3, the name of the printer port on
the print server.
You will need to perform the tasks below, logged in as the
superuser (root). To configure your Unix host for printing,
38
1. Optionally, assign a name corresponding to the print
servers IP address. You can add this address to the
/etc/hosts file, by adding a line such as:
203.66.191.186 pserver
2. Create a spool directory for the printer in the same
directory where spool directories are normally kept on the
machine, such as /var/spool or /var/spool/lpd:
mkdir /var/spool/lpd/pserverd
chown daemon /var/spool/lpd/pserverd
chgrp daemon /var/spool/lpd/pserverd
chmod 775 /var/spool/lpd/pserverd
3. Add an entry to the hosts /etc/printcap file, similar to
the following:
printer-name:\
:lp=:\
:rm=203.66.191.186:\
:rp=lpt1:\
:lf=/var/spool/lpd/pserverd.log:\
:sd=/var/spool/lpd/pserverd:\
:mx#0:
Lines should be indented with tabs. More than one printer
name can be used, with variants separated by vertical bars
(name1|name2).
The rm= entry should correspond to the IP address you
have assigned to the print server. You can also use a host
name if you have assigned one in the /etc/hosts file.
The sd= entry should correspond to the spool directory you
created in the previous step.
The rp= entry should correspond to the port name of the
remote printer. The values should be one of lpt1, lpt2 or
lpt3 depends on the printer port.
The print server should now be available for printing from
your Unix host.
39
7. Configuration Utility
7.1 Introduction
This chapter introduces print servers system configuration
utility in Windows environment. This utility is automatically
installed during Windows Administrator Utility installation
procedure - refer to section 3.2 and 3.3.
This utility provides the most complete management and
configuration functions on the print server side. This utility
only provides configuration functions for print server itself;
it does not include configuration functions for client side or
other file server or NetWare server in the network
environment.
The Configuration Utility provides the following
configuration and management functions:
Search Print Server: Search All Available Printer Servers
on the Network.
Print Server Status: Display Print Server Network Status.
AppleTalk Configuration: AppleTalk Protocol Setting.
General Configuration: General Information of print server.
NetWare Configuration: NetWare Printing Configuration.
System Configuration: Print Server Network Ability
Setting and Firmware Upgrade.
TCP/IP Configuration: IP Address and DHCP Server
Configuration.
Wireless Configuration: Wireless LAN Configuration.
SNMP Configuration: SNMP Information Configuration.
Setup Wizard: Guide You Through All the Settings.
Report: List the Status of All Available Print Servers on the
Network.
We will explain each function separately in the following
section.
40
7.2 Search for All Available Print Server
Every time when you run print servers configuration utility,
click the Search icon on the tool bar. The
configuration utility will delay for several seconds because
the utility is using systems available network protocols to
search for all print servers on the network. All available
print servers will be listed under Print Server Group on
the left side of the window.
You must select the print server you would like to configure
from the list. The system will, at the same time, display the
selected print servers status on the right side of the
window.
41
7.3 Status of Print Server
Click Status icon on the tool bar, the status of the
current selected print server will be showed on the right
side of the window.
The information of the print server displayed are MAC ID,
Model Type, Firmware Version, status of each printer port,
NetWare file server name, NetWare file server polling
interval, NetWare printer queue names, IP address, subnet
mask, default gateway, AppleTalk printer type, AppleTalk
zone and print server printing abilityetc.
You can refresh the print servers status by pressing the
Refresh button .
You can restart the print server by pressing the Reboot
button .
42
7.4 Setup the Print Server
Click Setup icon on the tool bar, the setup items of the
current selected print server will be showed on the right
side of the window.
Double click one of the icons to set up the selected print
server. A screen will pop up to verify User Name and
Password of the print server. The default values are as
follows.
Ÿ User Name: admin
Ÿ Password: 1234
43
7.5 AppleTalk Configuration
Double Click AppleTalk icon and the AppleTalk
configuration window will pop-up.
AppleTalk is a data communication protocol often used by
Macintoshes. The print server can use these parameters to
join the AppleTalk network and share the printer to other
AppleTalk workstations. You have to setup the Zone
Name and Printer Type for each printer port of this print
server.
Zone Name: Print server has to join zones of AppleTalk
before it can be shared to other workstations. Only
workstations in the same zone can share the printer. If you
want to share the printer to all workstations in all Zones,
you should enter only * in the Zone Name field.
Printer Type, the type of printer attached to each printer
port. You can get the printer type from the manufacturer of
the printer.
44
7.6 General Configuration
Double Click General icon and the General configuration
window will pop-up.
You can see basic print server information in this page.
You also can configure the Print Server Name, SMB
Group Name, User Name and Password here.
Printer Server Name, the name of the print server. You
can use this name to identify the print server when you are
searching for the print server by the administration and
client utilities.
SMB Group Name, the name of SMB group that this print
server belongs to. All PC should join the same group before
they can use this print server by SMB protocol.
User Name / Password is used to authenticate the
administrator by the Web administration tool.
45
7.7 Netware Print Server Configuration
Double Click NetWare icon and the NetWare configuration
window will pop-up.
This print server supports NetWare Bindery Printing method.
The print server periodically polls the NetWare server
printer queues for printing jobs. You have to assign the
NetWare server name, print server polling interval and the
name of queue on the NetWare server for each printer port.
Polling Time is the polling interval of the print server for
waiting printing jobs on the NetWare server.
NetWare Server is the name of the NetWare file server that
provides printer queues.
46
7.8 System Configuration
Double Click System icon and the System configuration
window will pop-up.
In the System configuration page, you can select to
enable/disable each printing or management protocol,
upgrade the new firmware for this print server, and
enable/disable wireless function.
Upgrade Firmware: You can use this Upgrade Firmware
tool to update the newest firmware of the print server. Click
button and select the correct firmware in your PC. After
selecting the firmware file, click the Upgrade button to
finish the firmware update process. If you want to reset the
Print Server to default factory settings, please click Load
Default.
Wireless Function: You can select Enable or Disable to
manually enable or disable the wireless function. If you
manually enable wireless function, the print servers
wireless LAN will be always enabled and Ethernet will be
always disabled. If you manually disable the wireless
function, the print servers wireless LAN will be always
disabled and Ethernet will be always enabled. You also can
select Auto to let the print server automatically decide to
47
enable or disable the wireless function. The print server
only can work in ether Ethernet or wireless LAN mode. It
cannot work in both Ethernet and wireless LAN mode at the
same time. When the print server starts up, it will auto-
detect if the LAN port is connected to an active network by
an Ethernet cable. If the print server is connected to an
active network by Ethernet cable when starting up, the print
server will run in Ethernet mode. If the print server is not
connected to an active network by Ethernet cable when
starting up, the print server will run in wireless LAN mode.
The print server default is in Auto mode.
Domain Country: The wireless channels are different from
country to country. Generally, the channels are from 1 to 11
in USA and from 1 to 13 in Europe. The Domain Country
setting is for you to set the available channels according to
your location.
48
7.9 TCP/IP Configuration
Double Click TCP/IP icon and the TCP/IP configuration
window will pop-up.
You can configure the print server to automatically get IP
from DHCP server or manually specify static IP. The print
server also has a built-in DHCP server. You can enable this
DHCP server and let it manages IP for you.
Click the IP button to enter the IP setting page. If you
need the print server to automatically get an IP from DHCP
server, select Auto IP. You also can select Static IP to
manually assign IP Address, Subnet Mask and
Gateway for the print server.
Click the DHCP Server button to enter the DHCP servers
setting page. You can Enable/Disable the DHCP server or
49
set Auto and assign a range of IP addresses here. The
DHCP server is disabled by default. If Auto is selected,
the DHCP Server of print server will be enabled only when
there is no other DHCP Server within the network. When
Enable or Auto is selected, you have to configure
Starting Address, Range, Subnet Mask, Gateway
Address and DNS. The print server will assign a unique
IP for each client.
50
7.10 Wireless Configuration
If you want to use the print server through wireless LAN, please set up the
print server through Ethernet first and make sure your wireless LAN setting
is correct. After setting the wireless LAN, unplug the Ethernet cable and
restart the print server, then you can start to use the print server through
wireless LAN. If the wireless configuration does not work, please plug the
Ethernet cable again, restart the print server and configure the print server
through Ethernet until the wireless LAN settings are correct.
The default settings of the print server wireless function are
as follows.
Ÿ Mode: Ad-Hoc
Ÿ SSID: Default
Ÿ Channel: 11
Double Click Wireless icon and the wireless configuration
window will pop-up.
If you use access point to build up wireless network, you
have to select Infrastructure Mode. If you do not have any
access point and want to use peer-to-peer connection to
build up wireless network, you have to select Ad-Hoc
Mode.
After selecting the operation modes of the wireless function,
click Next to go to further detailed configuration.
Infrastructure Mode:
51
In the Infrastructure mode, you have to let the print server
associate with an access point. You let the print server
scan for an available access point automatically or
manually assign the SSID of the access point you want to
use.
If you select to let the print server scan for an available
access point, the following window will pop up.
The list is the scanned available access points. Select an
access point in the list and click Next. If you cannot find
the access point that you want to use, click Scan to let
the print server scan again.
Ad Hoc Mode:
52
In the Ad-Hoc mode, you can let the print server
automatically associate with other wireless station or
manually assign the SSID of your wireless network. You
can let the print server automatically select the channel
that is the same with the peer or manually assign a channel.
If you select to let the print server scan for an active
wireless station, the following window will pop up.
The list is the scanned active wireless stations. Select a
wireless station in the list and click Next. If you cannot
find the wireless station that you want the print server to
communicate with, click Scan to let the print server scan
again.
Both Infrastructure and Ad-Hoc mode have to go
through the following procedure:
53
This print server supports WEP and WPA-PSK security
mode. If you want to use WEP encryption to protect your
wireless network, you have to select WEP(ASCII) or
WEP(HEX). If you want to use WPA-PSK, you have to
select WPA-shared key. The wireless security setting
should be the same with other wireless devices in the same
network.
WEP Security Mode:
54
You can select 64 bit or 128 bit length and
Hexadecimal or ASCII format for the encryption key.
Longer key length can provide stronger security but worth
communication performance.
Enter four key values by following the rules below and
select one key as the default key.
Ÿ PassPhrase A passphrase simplifies the WEP encryption process by
automatically generating the WEP encryption keys for the print server.
This setting is only valid when the security mode is in WEP(HEX).
Ÿ Key 1 to Key 4 If the key length is 64-bit, enter 10-digit Hex values
or 5-digit ASCII values as the encryption keys. For example:
0123456aef or Guest.
If the key length is 128-bit, enter 26-digit Hex values or 13-digit ASCII
values as the encryption keys. For example:
01234567890123456789abcdef or administrator.
WPA-shared key Security Mode:
55
When WPA-shared key, also named WPA-PSK requires
users to select the advanced encryption methods, i.e. TKIP
and enter a set of shared key.
Ÿ TKIP TKIP (Temporal Key Integrity Protocol) changes the temporal
key every 10,000 packets. This insures much greater security than the
standard WEP security.
Ÿ Shared Key Enter 8 to 63 digits of ASCII format to be the key for the
authentication within the network.
When you finish configuring the wireless security, click
Next to go to next step.
56
You can select to let the print server automatically obtain
IP settings with DHCP client or manually assign the IP
settings.
If you manually assign the IP settings, you have to enter IP
address, subnet mask and default gateway address.
When you finish configuring the IP settings, click Next to
confirm the IP Address configuration.
Click Save to save the wireless configuration.
57
7.11 SNMP Configuration
Double Click SNMP icon and the SNMP configuration
window will pop up.
Contact: You can enter the print server administrators
contact information here. This information will be displayed
in the SNMP management tool.
Location: You can enter the installed location of the print
server here. This information will be displayed in the SNMP
management tool.
7.12 Wizard
58
Click Wizard icon on the tool bar, the setup wizard
item of the current selected print server will be showed on
the right side of the window.
Double click the Print Server Setup Wizard the setup
wizard will guide you through all the setup process.
Step 1: Set up the name of this print server and the SMB
Group Name for the print server. Also set up Enable,
Disable or Auto for the wireless function here. Please
refer to section 7.6 and 7.8 for detail information.
Step 2: Select to enable required printing protocol. Please
refer to section 7.8 for detail information.
59
Step 3: Setup the IP of this print server and the DHCP
server. Please refer to section 7.9 for detail information.
Step 4: Setup the AppleTalk printing. Please refer to
section 7.5 for detail information.
Step 5: Setup the NetWare printing. Please refer to section
7.7 for detail information.
60
Step 6: Select the Wireless Adapter mode and complete
wireless LAN settings. The other procedures are the same
with Wireless Setting in Setup screen. Please refer to
section 7.10 for detail information.
Step 7: Click Save to finish setting.
61
7.13 Report
Click Report icon on the tool bar, the Report window
will pop up.
The report lists basic information of all available print
servers on the network. The information includes Device
Name, MAC ID, Model Type, Firmware Version and Status
of print server.
62
8. Web Management
8.1 Introduction
Print server can be configured and managed on the Web.
Through Local Area Network, or even Internet,
administrator can easily configure and manage print
servers various main functions in browsers. Simply enter
print servers IP address into your browsers address field
to manage a print server by print servers built-in Web
Server.
The default IP Address, User Name and Password settings
of the Print server are as follows.
IP Address: 192.168.2.2
User Name: Admin
Password: 1234
8.2 Login
You may use any Web Browser to review the status or configure the settings
of the print server. After entering the IP address of the print server, a login
page display. You have to enter correct User Name and Password before
going to the Web Management pages.
Notes: Default User Name is admin, default password is 1234.
63
8.3 Device Status
8.3.1 System
System Information includes Device Name, Print Server Name, Model
Type, System Up Time, Firmware Version, MAC Address, Wireless
LAN Status and the protocols enabled status, etc.
8.3.2 Printer
This page lists information of printers connected to all printer ports.
64
8.3.3 TCP/IP
This page lists all TCP/IP settings of the print server including IP Address,
Subnet Mask and Gateway. It also lists DHCP server setting.
8.3.4 SMB
This page lists the SMB group setting of the print server.
65
8.3.5 SNMP
This page lists the SNMP settings of the print server. It includes the settings
of SNMP System Contact and SNMP System Location.
8.3.6 NetWare
This page lists NetWare settings, including Polling Time, Use Bindery
Mode, Name of the File Server and Port Attached Queue.
66
8.3.7 AppleTalk
This page lists AppleTalk settings, including AppleTalk Zone Name and
Printer Type of printers connected to all print ports.
8.4 Setup Wizard
8.4.1 System
You can change the print server name and password of the
print server from here.
67
Print Server Name, the name of the print server. You can
use this name to identify the print server when you are
searching for the print server by the administration and
client utilities.
Password, enter the password you want to change to the
print server. The password can be up to 7-digit
alphanumeric format. The default password is 1234.
Re-type Password, enter the password you want to change
to the print server again.
8.4.1.1 Advanced Settings
You can enable/disable the printing protocols from the
screen. To enable the function, please select Enable; to
disable the function, please select Disable.
8.4.2 Wireless Setting
If you want to use the print server through wireless LAN,
please set up the print server through Ethernet first and
make sure your wireless LAN setting is correct. After
setting the wireless LAN, unplug the Ethernet cable and
restart the print server, then you can start to use the print
68
server through wireless LAN. If the wireless configuration
does not work, please plug the Ethernet cable again,
restart the print server and configure the print server
through Ethernet until the wireless LAN settings are correct.
8.4.2.1 General Setting
You can enable/disable the wireless function and set
parameters that are used for the wireless stations to
connect to this print server from here. The parameters
include Function, Mode, ESSID and Channel
Number. You can manually set the parameters of wireless
LAN in this page or use the Site Survey function to
automatically search for an available access point and
associate with it.
Function is for user to disable, enable or let the print
server auto select to connect to the wired or wireless
network. If Disable is selected, the print server can only
connect to the network through wired Ethernet. If Enable
is selected, the print server can only connect to the network
through Wireless LAN. If Auto is selected, the print server
can automatically decide to enable or disable the wireless
function. The print server only can work in ether Ethernet or
69
wireless LAN mode. It cannot work in both Ethernet and
wireless LAN mode at the same time. When the print server
starts up, it will auto-detect if the LAN port is connected to
an active network by an Ethernet cable. If the print server
is connected to an active network by Ethernet cable when
starting up, the print server will run in Ethernet mode. If the
print server is not connected to an active network by
Ethernet cable when starting up, the print server will run in
wireless LAN mode. The print server default is in Auto
mode.
Mode is the operation mode of wireless station. You can
choose ether Ad Hoc or Infrastructure mode. If you do
not have any access point and want to use peer-to-peer
connection, you have to choose Ad Hoc mode. If you have
an access point as the wireless LAN infrastructure, you
have to choose Infrastructure mode.
ESSID is the unique name identified by in a wireless LAN.
The ID prevents the unintentional merging of two co-
located WLANs. Please make sure that the ESSID of all
stations and access points in the same WLAN network are
the same.
Channel Number is the channel number of your wireless
LAN. Please make sure that the channel number of all
stations and access points in the same WLAN network are
the same.
8.4.2.2 Encryption
This print server supports WEP and WPA-PSK security
mode. If you want to use WEP encryption to protect your
wireless network, you have to select WEP. If you want to
use WPA-PSK, you have to select WPA-shared key. The
wireless security setting should be the same with other
wireless devices in the same network.
WEP Security Mode:
70
Key Length You can choose 64-bit to use WEP with 64-bit key
length encryption or choose 128-bit to use WEP with 128-bit key
length encryption. The longer key length can provide better security
but worse transmission throughput.
Key Format You may select to use ASCII Characters
(alphanumeric format) or Hexadecimal digits (in the "A-F", "a-f" and
"0-9" range) to be the WEP Key.
PassPhrase A passphrase simplifies the WEP encryption
process by automatically generating the WEP encryption keys for
the print server.
Default Key Select one of the four keys to encrypt your data. Only
the key you select it in the Default key will take effect.
Key 1 Key 4 The WEP keys are used to encrypt data
transmitted within the wireless network. Fill the text box by following
the rules below.
71
64-bit WEP: input 10-digit Hex values (in the "A-F", "a-f" and "0-9"
range) or 5-digit ASCII character as the encryption keys. For
example: 0123456aef or Guest.
128-bit WEP: input 26-digit Hex values (in the "A-F", "a-f" and "0-9"
range) or 10-digit ASCII characters as the encryption keys. For
example: 01234567890123456789abcdef or administrator.
WPA-PSK Security Mode:
When WPA-PSK, also named WPA-shared key requires
users to select the advanced encryption methods, i.e. TKIP
and enter a set of shared key.
Ÿ TKIP TKIP (Temporal Key Integrity Protocol) changes the
temporal key every 10,000 packets. This insures much greater
security than the standard WEP security.
Ÿ WPA Key Enter 8 to 63 digits of ASCII format to be the key for
the authentication within the network.
When you finish configuring the wireless security, click
Save & Next to confirm the configuration.
72
8.4.2.3 Site Survey
You can use this Site Survey function to search for
available access points in you location. In the list is the
information of all available access points or wireless
stations, includes SSID, BSSID, Channel, Type, Encryption
and Signal Strength. You can select one wireless device in
the list for this print server to associate with or you have to
use General Setting to manually setup the wireless
parameters.
There is WLAN Function setting for you to setup
Auto/Disable/Enable wireless function of the print server
here. Please refer to section 8.4.2.1 to know more about
the setting.
73
8.4.3 TCP/IP
You can configure the print server to automatically get IP
from DHCP server or manually specify static IP. The print
server also has a built-in DHCP server. You can enable this
DHCP server and let it manages IP for you.
If you need the print server to automatically get an IP from
DHCP server, select Enable Obtain TCP/IP Settings
Automatically (Use DHCP/ BOOTP). You also can select
Disable Use the following TCP/IP Settings to manually
assign IP Address, Subnet Mask and Gateway for the
print server.
You can enable/disable or set auto for the print servers
DHCP server. The DHCP server is disabled by default. If
the DHCP Server is enabled or set Auto, you have to
assign a range of IP addresses here. Fill in the Start IP,
Range, DNS, Subnet Mask and Gateway, and the
print server will assign a unique IP for each client. Note
that when Auto is selected, the DHCP Server of the print
server will be enabled only when there is no other DHCP
Server within the network.
74
8.4.4 SMB
You can enable/disable the SMB protocol from here. If SMB
is enabled, enter the SMB Group Name to specify the
SMB group that this print server belongs to. All PC should
join the same group before they can use this print server by
SMB protocol.
8.4.5 SNMP
75
The print server supports SNMP configuration. If it is
enabled, please set up the following parameters.
SNMP System Contact: You can enter the print server
administrators contact information here. This information
will be displayed in the SNMP management tool.
SNMP System Location: You can enter the installed location of the print
server here. This information will be displayed in the SNMP management
tool.
8.4.6 NetWare
This print server supports NetWare Bindery Printing method.
The print server periodically polls the NetWare server
printer queues for printing jobs. You have to assign the
NetWare server name, print server polling interval and the
name of queue on the NetWare server for each printer port.
Polling Time is the polling interval of the print server for
waiting printing jobs on the NetWare server.
Name of the File Server is the name of the NetWare file
server that provides printer queues.
76
8.4.7 AppleTalk
AppleTalk is a data communication protocol often used by
Macintoshes. The print server can use these parameters to
join the AppleTalk network and share the printer to other
AppleTalk workstations. You have to select to enable or
disable AppleTalk, and setup the Zone Name and Printer
Type for each printer port of this print server.
AppleTalk Enable: Enable or disable AppleTalk.
AppleTalk Zone Name: Print server has to join zones of
AppleTalk before it can be shared to other workstations.
Only workstations in the same zone can share the printer. If
you want to share the printer to all workstations in all
Zones, you should enter only * in the Zone Name field.
Printer Type, the type of printer attached to each printer
port. You can get the printer type from the manufacturer of
the printer.
77
8.4.8 Save Settings
You can click the Save Settings to save the settings and
restart the system.
78
8.5 System Tools
8.5.1 Load Default
You can use this page to restore the factory default
settings. All of your previous setup will be cleared.
8.5.2 Upgrade Firmware from Browser
79
You can upgrade new firmware for this print server in this page. Click
Browse to select the new firmware in your storage and then click OK, the
firmware will be updated in several minutes.
Be aware that if you have started upgrading firmware, you have to follow all
the upgrading steps or the print server cant turn back to normal
configuration.
9. IPP Printing
9.1 Introduction
IPP (Internet Printing Protocol) Printing provides a
convenient way of remote printing service by TCP/IP. The
print server can support IPP printing by default. It is
needless to do any setting. Any PC that can support IPP
printing, for example Windows 2000/XP, can directly uses
the print server by IP. By using the IPP printing, you can
share the printer to all the PCs that can access the print
server by IP. You can even share your printer to Internet
users.
80
9.2 System Setup
9.2.1 Print Server Side
It is needless to do any setting on the print server side.
Make sure the print server has correct IP settings. If you
want to share the printers to Internet users, you have to set
a real IP to the print server. You also have to make sure
that any gateway, router or firewall does not block IPP
protocol if you have these gateway devices installed in your
network.
9.2.2 Client Side
You only need to perform Windows standard Add New
Printer procedure.
Step1. Click Start, choose Settings and select Printers
and Faxes.
Step2. Click Add a Printer.
Step3. The Add Printer Wizard is displayed. Click Next.
Step4. Select A network printer, or a printer attached to
another computer. Click Next.
81
Step5. Select Connect to a printer on the Internet or on a
home or office network and enter the URL of print server.
The URL format is http://IP:631/Port Name. The IP should
be the print servers IP. The number 631 is IPP standard
port number. Port Name is the port name of print server
that your printer is connected to. The default port name is
lpt1. One example of the URL is
http://192.168.3.66:631/lpt1. After entering the URL of print
server, click Next.
Step6. Select a suitable printer manufacturer and the
printer model and click Next. If your printer is not in the
list, click Have Disk…” to install the driver of the printer.
After installation, the printer model will be added to the list.
82
Step7. Choose to set the print whether as a default printer
or not. Click Next.
Step8. You have added the network printer to the PC
successfully. The information of the printer is displayed in
the windows. Click Finish.
83
10. Windows XP SP2 Setup
In Windows XP SP2, XP SP2s firewall would block the
unknown communications. This print server has allowed the
communications data passed through the XP SP2s firewall.
In case that you do not find any print server listed on the
Available Ports in Network Ports Quick Setup, please
follow the steps below.
Step1. Click Start, choose Settings and select
Network Connections.
Step2. Right click Local Area Connection and select
Properties.
Step3. Select Advanced tab and click Settings…”.
84
Step4. Select Exceptions tab and click Add Program…”.
85
Step5. Click Browse to add a new program.
Step6. Open the NPUtil file from C:\Program
Files\PrintServer Utilities (where C:\ is the system drive).
Step7. A new program Network Ports Quick Setup is
displayed in the list, click Ok.
86
Step8. Click Ok. You have completed the setting. The
Windows XP SP2 will allow the incoming network
connections activated by the program.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Edimax PS-1206UWg bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Edimax PS-1206UWg in de taal/talen: Engels als bijlage per email.

De handleiding is 4,03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info