810815
42
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
42
ENGLISH
Lighting a hot fireplace
When should wood be added? When the fuel is
almost completely consumed to embers. With the
glove supplied, slowly open (to avoid formation of
vortexes that can cause smoke to exit) the door. Add
the desired wood to the fireplace, locating it on the
existing embers (within the quality limits indicated in
the technical table).
Stove functioning changes with the chimney flue draft
and adjustment of the air valve in combustion.
Functioning with initial low draft
To extract air for combustion and discharge the
smoke, the fireplace needs a draft to be exerted on the
chimney flue.
If the draft is weak, initially light a “starter” fire using
small sized lighting material.
Once the correct draft is restored, you can add the fuel.
As with all the products, the wood stove heats and
cools during the various phases. This would lead to
normal dilation. Such dilation can cause slight settling
noise, which is not a reason for dispute.
The hot air reaches the premises with natural motion
(natural convection) without the help of a fan.The
retailer also offers an Air Diffuser kit with fans to
distribute the hot air in the premises.
NOTE FOR UK
Refuelling on to a low fire bed
If there is insufficient burning material in the firebed to
light a new fuel charge, excessive smoke emission can
occur. Refuelling must be carried out onto a sufficient
quantity of glowing embers and ash that the new fuel
charge will ignite in a reasonable period. If there are
too few embers in the fire bed, add suitable kindling to
prevent excessive smoke
Fuel overloading
The maximum amount of fuel specified in this manual
should not be exceeded, overloading can cause
excess smoke.
ISTRUCTIONS FOR USE
First switch on phases
Ensure you have read and understood the content
of this manual
Remove all the inflammable parts from the product
(manuals, labels, etc.). In particular remove any
labels from the glass. If they melt, they would
irreversibly damage the glass.
For initial switch on of the fireplace, always use the
smallest logs. Use larger wooden logs to raise the fire.
Always locate the wood deep in the fireplace, almost in
contact with the rear wall, so that even if they slide they
won’t come in contact with the glass.
There may be a slight smell of paint the first few times it
is ignited, however, this will disappear quickly.
Lighting a cold fireplace
1. Check the existing ash bed is not too high. If the
ash bed is too high, there is a danger of opening the
door of the fireplace to add wood and possible brazier
fragments fall out of the fireplace.
2. Position the adjustment lever of the valve in the “total
opening” position. The air for combustion will flow
intensely to the wood in the fireplace, to quickly reach
good combustion.
3. place the wood in the fireplace without excessively
squashing it in. Position a firelighter between the wood
logs and light. Never user materials such as petrol,
alcohol and similar to switch on.
4. At this point, close the door and monitor it for a few
minutes. If the fire should extinguish, slowly open the
door, re-position another firelighter between the logs
and light again.
42

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Edilkamin Tally 8 Up S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Edilkamin Tally 8 Up S in de taal/talen: Engels als bijlage per email.

De handleiding is 13.3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Edilkamin Tally 8 Up S

Edilkamin Tally 8 Up S Gebruiksaanwijzing en installatiehandleiding - Nederlands - 48 pagina's

Edilkamin Tally 8 Up S Gebruiksaanwijzing en installatiehandleiding - Deutsch - 48 pagina's

Edilkamin Tally 8 Up S Gebruiksaanwijzing en installatiehandleiding - Français, Italiano - 96 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info