810851

Edilkamin Firebox Luce Plus Handleiding

13
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
13
ENGLISH
INSTALLATION
INSTALLATION IN AN EXISTING FIREPLACEINSTALLATION IN AN EXISTING FIREPLACE
FITTED WITH EXTERNAL AIR INTAKEFITTED WITH EXTERNAL AIR INTAKE
(when part numbers are not specifi ed, refer to the (when part numbers are not specifi ed, refer to the
specifi cation tables on the previous pages)specifi cation tables on the previous pages)
N.B.: if you do not want to alter the existing hood, the N.B.: if you do not want to alter the existing hood, the
installation must be carried out without hot-air ducting installation must be carried out without hot-air ducting
(leaving the upper outlets closed).(leaving the upper outlets closed).
In this case, the hot air only enters the room through In this case, the hot air only enters the room through
the slots on the front, above the door.the slots on the front, above the door.
a) make a pit (Fig. A), in the basement of the existing a) make a pit (Fig. A), in the basement of the existing
fi replace, big enough to hold the external air intake fi replace, big enough to hold the external air intake
mechanism (Fig. B)mechanism (Fig. B)
b) this pit must communicate with an external air inlet b) this pit must communicate with an external air inlet
duct through a passage with cross-sectional area of at duct through a passage with cross-sectional area of at
least 80-200 cm² (depending on the model)least 80-200 cm² (depending on the model)
c) position the mechanism (Fig. B) fl ush with the upper c) position the mechanism (Fig. B) fl ush with the upper
face of the fl oor, carefully sealing the points where face of the fl oor, carefully sealing the points where
outside air may leak d) make sure the damper moves outside air may leak d) make sure the damper moves
correctly (Fig. B)correctly (Fig. B)
e) with a hose clamp Ø 16-20 cm fi t a length of at least e) with a hose clamp Ø 16-20 cm fi t a length of at least
2 meters of stainless steel flue, with the fi tting for a Ø 2 meters of stainless steel flue, with the fi tting for a Ø
16 cm flue or the fi tting for a Ø 20 cm flue (Fig. C)16 cm flue or the fi tting for a Ø 20 cm flue (Fig. C)
f) wrap the section of steel pipe with a multilayeredf) wrap the section of steel pipe with a multilayered
ceramic fi bre mat or equivalent material (Fig. C)ceramic fi bre mat or equivalent material (Fig. C)
g) slip the section into the flue of the existing fireplace g) slip the section into the flue of the existing fireplace
and make sure the thickness of the ceramic fi bre and make sure the thickness of the ceramic fi bre
wrapping is suffi cient to completely fill the space wrapping is suffi cient to completely fill the space
between the new steel pipe and the existing flue (Fig. C)between the new steel pipe and the existing flue (Fig. C)
h) place Firebox® onto the mechanism (Fig.B) h) place Firebox® onto the mechanism (Fig.B)
checking that:checking that:
- the lower fl ange has been removed to allow the fl ow - the lower fl ange has been removed to allow the fl ow
of external air;of external air;
- The defl ector is open, using the knob located at the - The defl ector is open, using the knob located at the
top left on the front of Firebox®;top left on the front of Firebox®;
- a seam of high temperature mastic has been inserted - a seam of high temperature mastic has been inserted
where the flue attaches and on the smoke outlet collar;where the flue attaches and on the smoke outlet collar;
i) lower the previously inserted stainless steel pipe until i) lower the previously inserted stainless steel pipe until
it fi ts into the Firebox® smoke outlet collar.it fi ts into the Firebox® smoke outlet collar.
Do this by hand in the space between Firebox® and Do this by hand in the space between Firebox® and
the top of the inlet to the existing chimneythe top of the inlet to the existing chimney
l) if Firebox® is ventilated, leave a space for the fan l) if Firebox® is ventilated, leave a space for the fan
power cord making sure it does not come into contact power cord making sure it does not come into contact
with hot partswith hot parts
m) carefully close off the remaining space between m) carefully close off the remaining space between
Firebox® and the edges of the inlet to the existing Firebox® and the edges of the inlet to the existing
chimney.chimney.
It can be closed off with a metal mantelpiece, brickwork It can be closed off with a metal mantelpiece, brickwork
or fi re retardant plasterboard. or fi re retardant plasterboard.
Leave a slight space between the closing material and Leave a slight space between the closing material and
Firebox® to allow for expansion.Firebox® to allow for expansion.
INSTALLATION IN AN EXISTING FIREPLACEINSTALLATION IN AN EXISTING FIREPLACE
WITHOUT EXTERNAL AIR INTAKEWITHOUT EXTERNAL AIR INTAKE
Check for the possibility of making a pit inside the
existing fi replace (Fig. A) by removing the fi re surface.
This pit must be big enough to hold the external air
intake mechanism (Fig. A) and must be connected to
the outside by a duct with cross-sectional area of Ø
80/200 cm2 (according to model) (Fig. B).
If it is not possible to do as described above, place a
80/200 cm2 external air intake as near to Firebox® as
possible.
In this case, the mechanism is not used and the lower
Firebox fl ange must not be removed.
Proceed with the installation as described in
the previous section from point “e” onwards.
INSTALLATION WITH A NEW, SPECIALLYINSTALLATION WITH A NEW, SPECIALLY
MADE COVERINGMADE COVERING
Position Firebox® according to the characteristicsPosition Firebox® according to the characteristics
of the new covering with which it will be completed.of the new covering with which it will be completed.
If the covering is produced by EdilKamin, you will fi If the covering is produced by EdilKamin, you will fi
nd instructions for correctly positioning Firebox® in the nd instructions for correctly positioning Firebox® in the
packaging.packaging.
Place the external air-intake mechanism and connect Place the external air-intake mechanism and connect
the lower inlet directly with the outside using a fl exible the lower inlet directly with the outside using a fl exible
aluminium tube or a specially made duct; Both having aluminium tube or a specially made duct; Both having
a minimum cross-sectional area of 80-200 cm2 (Fig. a minimum cross-sectional area of 80-200 cm2 (Fig.
B) (depending on model).B) (depending on model).
Place Firebox® onto the mechanism and make sure Place Firebox® onto the mechanism and make sure
the lower fl ange has been removed to allow the fl ow the lower fl ange has been removed to allow the fl ow
of external air (Fig. B).of external air (Fig. B).
Connect Firebox to the flue with a Ø 16 or Ø 20 cm Connect Firebox to the flue with a Ø 16 or Ø 20 cm
pipe. Complete with the chosen covering and install pipe. Complete with the chosen covering and install
the kits for hot-air circulation (see followingthe kits for hot-air circulation (see following
instructions).instructions).
… 13 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Edilkamin Firebox Luce Plus bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Edilkamin Firebox Luce Plus in de taal/talen: Engels als bijlage per email.

De handleiding is 1.13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Edilkamin Firebox Luce Plus

Edilkamin Firebox Luce Plus Gebruiksaanwijzing - Deutsch - 28 pagina's

Edilkamin Firebox Luce Plus Gebruiksaanwijzing en installatiehandleiding - Deutsch, English, Français, Italiano, Português, Espanõl - 80 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info