810847
25
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
25
INSTALLER
IMPORTANT! BEFORE PROCEEDING WITH
IGNITION, CAREFULLY READ ALL THE
INSTRUCTIONS AND PRECAUTIONS SHOWN IN
THIS BOOKLET.
First ignition could be difficult because of
the possible presence of air in the gas pipe.
In case of short ignition or switch-off of the
appliance, wait at least 5 minutes before repea-
ting the ignition operation.
When first ignited, the Appliance may give
off a bad smell or vapours. This is entirely
normal. The best thing is to ventilate the premi-
ses adequately.
After igniting, allow the appliance to operate
for about ten minutes at maximum output,
to permit adequate heating.
If the appliance is to be used for short
periods of time, it is best not to switch it off
but rather leave it with the pilot light on. This
way, the formation of condensation is prevented
in the pipes that reach the flue and which, in the
long term could cause hearth corrosion.
REMOTE CONTROL UNIT
Ignition
• Open the gas supply tap.
• Press the switch (5) of the gas valve in “ I “ position.
Make sure the knob (7) of the manual operation
mechanism is positioned on “ON”.
Press the keys OFF and triangle UP of the
remote control at the same time.
An acoustic signal will indicate the start of the start
sequence. The electronic system checks correct gas
flow and ignites the main burner (these operations
could take up to 20 seconds). After burner ignition,
the flame automatically positions on maximum.
If the pilot flame goes out, wait at least five
minutes before repeating the described ope-
ration. During the start phase, the knob of the
manual operation mechanism must be positio-
ned on “ON”.
Operation
Setting the electronic code for RF remote con-
trols (with or without display).
A code is selected automatically between 65000 ran-
dom codes available. The receiver (at the edge of
the chimney) must know the remote control code:
Expected sequence:
- Press and hold the RESET button of the receiver in
the fireplace until you hear two (2) beeps: the first is
short and the second is long. After the second beep,
release the RESET button.
- Within the next 20 seconds, press the button (small
flame) on the remote until you hear two short beeps,
which further confirm the correct setup code. If you
hear one long beep, the acquisition sequence code
failed or the wiring is incorrect.
This setting is performed only once and is
not required after changing the batteries on
the remote or receiver.
Once turned on, you can choose the power level of
the Device using the remote control. Press the remo-
te button "triangle DOWN" to reduce the intensity of
the flame and press "triangle UP" to raise it.
Once the Appliance has been switched on,
the Manufacturer suggests leaving it run-
ning for 10 minutes at max output, before making
any adjustments.
At minimum, the burner remains off, leaving on only
the pilot flame.
From minimum position, the output can be turned up
without repeating the ignition operation.
5
7
1
MAX
OFF
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Edilkamin EKT130 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Edilkamin EKT130 in de taal/talen: Engels als bijlage per email.

De handleiding is 12.82 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Edilkamin EKT130

Edilkamin EKT130 Gebruiksaanwijzing en installatiehandleiding - Deutsch - 34 pagina's

Edilkamin EKT130 Gebruiksaanwijzing en installatiehandleiding - Français - 34 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info