810882
44
Verklein
Vergroot
Pagina terug
1/158
Pagina verder
ENGLISH
43
Filling the feed screw
If the pellet storage tank is completely emptied, it follows that the Archimedes' screw is also emptied. Before restarting the stove you
must fill it by following these steps: press the +/- keys simultaneously (via the radio control/ remote control or the synoptic panel) for
a few seconds, after which, having released the keys, the display will show the text "Reload".
It is quite normal for some pellet residue to remain inside the hopper, this is what the feed screw is unable to pick up. Once a month,
fully vacuum the hopper to prevent dusty residue from accumulating.
Automatic ignition
With the thermo-stoves on stand-by, press the 0/1 button for 2 seconds (on the synoptic panel or radio control/ remote control). This
will start-up the ignition process, ‘Start’ will appear on the display and a countdown will commence in seconds (1020). There is no
preset time for the ignition process: its duration will be automatically shortened if the control board detects that certain tests have been
carried out positively. The flame appears after about 5 minutes.
Manual ignition(in case of start up failure)
At a temperature lower than 3 °C – too low for the electrical resistance to become red hot - or if the resistance is temporarily not
working, you can use a firelighter to ignite the thermo-stoves.
Insert a well-lit firelighter into the combustion chamber, close the door and press 0/1 on the synoptic panel or radio control/ remote
control.
Operating modes
Operating from synoptic panel/radio control/ remote control. With the thermo-stoves running or on stand-by, from the synoptic panel:
- press the + or – keys to increase or decrease the desired water temperature.
- by pressing the key you can change the SET temperature of the boiler or of the secondary circuit in general, using the +/-
keys. It is possible to visualise (if the boiler probe is connected) the temperature of any boiler/external storage, by pressing the "boi-
ler" key the set value is displayed, by pressing the +/- keys while viewing the boiler value set that setting can be varied. If the boiler
probe is not connected dashes appear in place of the temperature (--.-° C).
Shutdown
While the stove is working pressing the 0/1 key for 2 seconds begins the shutdown process and "OFF" is displayed (for 10 minutes).
The turning off phase includes:
-The interruption of falling pellets
-The circulation of running water.
Never pull the plug during shutdown.
N.B.Please note that the circulator runs until the water temperature drops below 40° C.
Setting the clock
Press the MENUbutton for 2 seconds and use the + and – keys to follow the instructions given on the display to access the ‘Clock’ menu.
This allows you to set the time on the electronic control board. Then press MENUand the following data appears in sequence – this
can be adjusted: day, month, year, hour, minutes, day of the week. When ‘Save?’ appears on the display, you can check that the set-
tings have been entered correctly before confirming. Press MENUto save the information (‘Save OK’ then appears on the display).
Programmer to ignite and shutdown the thermo-stoves at various times during the week.
Press the MENU button on the radio control/ remote control for 2 seconds to access the time setting function and press the + key to
access the weekly timer function ‘Program ON/OFF’ will appear on the display.
The timer allows you to set a number of ignitions and shutdowns per day (up to a maximum of three), for each day of the week. As
you confirm via the MENUbutton, one of the following options will appear:
- No Prog. (no program is set)
- Program/daily (a single program is set for every day)-
- Program/weekly (a program is set for each day of the week)
Move from one to the other using the + and – keys.
Use the MENUbutton to confirm the ‘Daily program’ option and access the selection of the number of programs (ignition/shutdown) to be set per day.
Use the ‘Program/daily’ option to set the identical program/s for every day of the week.
The following will be displayed if the + key is pressed:
- No Prog.
- Prog. No. 1 (one ignition and one shutdown per day), Prog. No. 2 (same as before), Prog. No. 3 (same as before)
Use the button to show them in reverse order. If the 1st program is selected, the ignition time is shown.
The display shows: 1 Ignition Hour 10.30; use the +/– keys to change the hour and press MENUto confirm.
The display shows: 1 Ignition Minutes 10.30; use the +/– keys to change the minutes and press MENUto confirm.
In the same way, adjust the shutdown times.
The program is confirmed by pressing the MENUbutton when “Saved” appears on the display.
When confirming ‘Program/week’, you will need to choose the day to which the program is to apply:
INSTRUCTIONS FOR USE
44

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Edilkamin ATLANTA bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Edilkamin ATLANTA in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 4.03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info