810928
31
Verklein
Vergroot
Pagina terug
1/182
Pagina verder
- 31 -
ENGLISH
Fig. 1/a
The fundamental characteristics of the chimneypot are:
- an internal cross-section at the base, which is the same as that
of the chimney À ue.
- an outlet cross-section which is no smaller than twice that of
the chimney À ue.
- its position must be high enough to catch the wind and avoid
downdraft areas in turbulent wind.
In addition to that mentioned above, please consider the
indications stipulated in UNI 10683/2005 standard, para-
graph 4.2: “connection to the smoke outlet system” and its
subsections.
- Use a stainless steel À ue to connect the thermo ¿ replace to the
chimney À ue, adhering with the diameters indicated in the spe-
ci¿ cations table and the guidelines given in the chapter called
“chimney À ues”.
- Verify that all moving parts function properly before setting
the thermo ¿ replace covering in place.
- This system must be tested and ignited for the ¿ rst time
before the covering is set in place.
The base of the thermo ¿ replace covering must allow the
internal air to be recycled. Therefore, suitable slots or apertures
must be made for the air to pass through. Parts of the thermo
¿ replace covering that are made of marble, stone and bricks
must be mounted with a small gap between them and the ¿ re-
place so as to prevent possible breakage due to expansion and
excessive overheating.
Protect wooden parts with ¿ reproof materials.
Fireproof parts of the covering (beams or frames) must not be
in contact with the ¿ replace unit but must be at least 1-2 cm
away to allow a À ow of air that prevents heat accumulation (see
Fig. 1/a).
The housing compartment must be made of masonry or ¿ repro-
of materials and must not have combustible elements inside.
The ¿ replace mantel can be made of ¿ reproof plasterboard
panels or gypsum board and, however, of completely ¿ reproof
material. Air should be allowed to À ow inside the ¿ replace
mantel (through the gap between the door and the beam).
Through convective motion, the air will À ow out from the grille
installed at the top, resulting in heat recovery and preventing
excessive overheating (See Fig. 1/a).
The ¿ replace mantel must have appropriate openings to carry
out maintenance on the ¿ ttings.
In addition to that mentioned above, please consider the in-
dications stipulated in the UNI 10683 standard, paragraphs
4.4 and 4.7: “insulation, ¿ nishing, ¿ replace covering and
safety recommendations”.
Insulating mats must be applied when using an installation
KIT so as to protect it from the heat radiation emitted by
the thermo ¿ replace.
45°
45°
3
NO
4
2
max.45°
1
NO
inspection
CHIMNEY FLUES AND CHIMNEYPOT
The thermo ¿ replace smoke outlet has a circular crosssection
so that stainless steel pipes can be used. If the chimney À ue
inlet is not vertically above the thermo ¿ replace, the connection
from the ¿ replace to the À ue must not have a narrowing
section or inclinations greater than 45° (¿ g. 1-2-3-4).
The ¿ replace unit must not be connected to a shared À ue.
The fume section must be inspectable and installed in such a
way that it can be cleaned (use inspectable TEEs).
If the chimney À ue is not brand new or too big, it is recommen-
ded to ¿ t in stainless tubes of an appropriate diameter and with
suitable insulation.
If the chimney À ue is installed outside, it is recommended to
use an insulated, double walled, stainless steel À ue.
The characteristics of the construction must be suitable to
withstand a smoke temperature of at least 450° C, with parti-
cular reference to the mechanical resistance, insulation and the
gas tight sealing.
The À ue must be certi¿ ed under EN 1856.
The junction of the steel À ue inlet and the smoke outlet of the
¿ replace must be sealed with high temperature mastic.
Have quali¿ ed personnel clean the À ue once a year.
INSTALLATION
INSTALLATION COVERING, FIREPLACE
MANTEL
If combining with a pre-fabricated Edilkamin covering, to de¿ -
ne the exact positioning of the thermo ¿ replace, it is important
to take the chosen covering model into consideration.
The positioning is implemented according to the model chosen
(refer to the installation instructions found inside the packaging
of each thermo ¿ replace covering).
Always ensure the thermo ¿ replace is level during the installa-
tion process.
- Drill a hole into the wall or the À ooring for the external air
intake and connect the air adjustment mechanism to the hole as
described in the chapter called “external air inlet”.
Hot air ŏ ow
grille
Mantel
Door slider
guide
Metal mantel
Hood
Wooden
beam
Front part
Air inlet in the
mantel
sliding door
31

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Edilkamin AQUAMAXI 28 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Edilkamin AQUAMAXI 28 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools als bijlage per email.

De handleiding is 5.98 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info