547014
12
Verklein
Vergroot
Pagina terug
1/23
Pagina verder
12
3. Using the rear cover as a template, mark the
positions of the fixing holes on the wall.
4. Fix the rear cover to the wall using the two 18mm
screws and 23mm wall plugs. Do not over-tighten
the fixing screws as this may distort or damage the
cover.
5. Configure the Motion Sensor as described below.
Remember that on initial installation that the device
needs to be tested and should therefore be set in
Walk Test Mode.
6. Check that the sensor PCB is located and set in
the correct position to provide the required
detection range. To adjust the PCB position,
simply slide it up or down ensuring that the location
legs are aligned with the required position number
marked on the board.
7. To refit the Motion Sensor to the rear cover and
locate the clips in the top edge into the rear cover.
Push the lower edge of the sensor into place and
refit the fixing screw in the bottom edge of the
Sensor to secure in position. Do not over-tighten
the fixing screws as this may damage the casing.
SETTING THE MOTION SENSORS
Located on the PCB of the Motion Sensor is a
two-position DIP switch (SW2). When conducting the
Walk Test, ensure that the DIP switch SW2 is set as
follows:
SW2 DIP1 DIP2
ON
OFF
1. DIP1 of SW2 is used to configure the Motion
Sensor for walk test mode, which allows the
operation of the sensor to be checked during
installation without triggering a Full Alarm.
ON Walk Test mode
OFF Normal mode
Note: Remove batteries before setting the SW2.
Refit batteries after setting the SW2.
Note: On initial installation the sensor should be
set into Walk Test mode ready for testing. Upon
completion of Walk Test mode, set DIP1 of SW2 to
OFF for normal detection mode.
2. The Motion Sensor incorporates an anti-false
alarm feature designed to compensate for
situations where the sensor may be affected by
environmental changes, (e.g. insects, air
temperature, etc). This feature is called
“sensitivity detection” and may be selected for high
or low detection.
The recommended setting is for high sensitivity
detection. However, in cases of extreme
environmental problems or if unattributable false
alarms are experienced, it may be necessary to
select low sensitivity detection.
Set the required sensitivity detection using DIP2 of
SW2 as follows:
ON high sensitivity detection
OFF low sensitivity detection
Note: The higher the sensitivity detection the less
movement will be necessary before the Motion
sensor will trigger the alarm.
3. The setting of the DIP1 & DIP2 of SW2 can be
distinguished from the LED indication as follows:
On/Off
Selection
DIP1 of
SW2
DIP2 of
SW2
Trigger reaction of LED
High
Sensitivity
LED will be on once.
It implies high
sensitivity.
ON Walk Test
mode
Low
Sensitivity
LED will flash twice. It
implies low sensitivity.
Dip Switch(SW2)
1
ON
2
Tamper Switch
5
4
3
2
1
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Eden HA700 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Eden HA700 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,95 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Eden HA700

Eden HA700 Gebruiksaanwijzing - Deutsch - 29 pagina's

Eden HA700 Gebruiksaanwijzing - Français - 29 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info