782670
4
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483
English
Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator
4
INSTALLATION
STEP 1. Remove shipping plugs from pump ports. Some water from factory testing may spill out.
STEP 2. Connect ttings supplied with the pump to your hoses. If using the slip-on barb
connections use hose clamps.
STEP 3. Mount pump horizontally or vertically. Read mounting instructions below.
STEP 4. Install inlet and outlet port connectors. Do not overtighten.
STEP 5. Install the strainer in an accessible location between the tank and pump inlet. This
strainer or equivalent is recommended.
MOUTING
(Please read before completing steps)
The pump can be at the same level or below the water tank. It may be positioned above the
water tank if needed, as it is capable of a 6ft. (1.8m) vertical prime. Horizontal inlet tubing will
allow priming to 30ft (9m)
Consider a dry location that allows easy access if maintenance is required. The pump should
not be located in an area of less than one cubic foot unless adequate ventilation is provided.
Excessive heat may trigger the integral thermal breaker and interrupt operation. When the
temperature drops the breaker will automatically reset and start proration.
The pump can be mounted horizontally or vertically. If mounting of the pump vertically, the
pump head should be in the down position.
The mounting feet are intended to isolate the pump from the mounting surface; over-
tightening, attening, or use of oversized screws will reduce the ability to isolate vibration
and noise through the lines.
INSTALLATION INSTRUCTIONS
Solid surface
Accessible location away from living quarters
Properly sized wiring
Proper electrical protection
Strainer on plumbing elbows and valves near the pump
Minimize ow restrictions in the system
WIRING
STEP 1. Use 14 gauge stranded wire to 20’, 12 gauge to 50’ from power source.
STEP 2. Use a 10-15 amp rated on-o switch on the (+) (red) motor lead
STEP 3. Install a 10 amp fuse protection on the positive lead.
ELECTRICAL
(Please read before completing steps)
The pump should be on a dedicated (individual) circuit protected by the specied fuse
indicated on the motor label.
A U/L, CE etc. approved marine duty (ignition protected) switch rated at above 15 amps is
recommended and must interrupt current ow on the positive (+ red) lead.
The pump must be grounded to a known ground (battery). The ground wire must be the
same size (gauge/Mm2) as the positive wire.
Wire sizing: Proper wire sizing is required for good pump operation. If the wire is too small,
low voltage will aect the pump performance and can create re hazard.
The total current draw on the circuit must not exceed 15 amps. If the pump is used in
conjunction with other components, overload current protection (fuse or circuit breaker) and
wire size must be for the total amp requirements of all devices on the circuit.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Eccotemp EccoFlo bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Eccotemp EccoFlo in de taal/talen: Engels als bijlage per email.

De handleiding is 5.89 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Eccotemp EccoFlo

Eccotemp EccoFlo Gebruiksaanwijzing - Nederlands - 10 pagina's

Eccotemp EccoFlo Gebruiksaanwijzing - Deutsch - 10 pagina's

Eccotemp EccoFlo Gebruiksaanwijzing - Français - 10 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info