488589
10
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
Model MM40
Voltage Rating: 220V-240V ~ 50/60Hz
Wattage Rating: 270W
No Load Speed: n(o) 10000-21000 min-1
Oscillation Angle, left/right: 1,5°
Weight: 1.46 kg
EXTENSION CORDS
Use completely unrolled and safe extension cords with a capacity
of 5 Amps.
ASSEMBLY
!
WARNING
ALWAYS TURN OFF THE TOOL BEFORE
CHANGING ACCESSORIES, CHANGING
COLLETS, OR SERVICING THE TOOL AND REMOVE BATTERY
PACK.
GENERAL
This Dremel Multi-Max Tool is intended for dry sanding of
surfaces, corners, edges, for scraping, for sawing soft metals,
wood and plastic components, and for grout removal using the
applicable tools and accessories recommended by Dremel.
PICTURE 1
A. On/Off switch
B. Variable speed control dial
C. Power cord
D. Ventilation openings
E. Blade washer
F. Accessory holder
G. Accessory
H. Clamping screw
PICTURE 2
A. Quick Lock™ lever
B. On/Off switch
C. Variable speed control dial
D. Power cord
E. Ventilation openings
F. Accessory holder
G. Accessory
H. Clamping flange
INSTALLING AND REMOVING ACCESSORIES
NOTE: Be sure to read the instructions supplied with your Dremel
accessory for further information on its use.
Use only Dremel tested, high performance accessories.
Dremel cutting, scraper blades have a Quick-Fit slot which allows
for faster accessory removal compared with other conventional
oscillating tool systems.
Model MM20
1. Loosen the clamping screw using the hex key provided
just enough so you can slide the accessory between the
accessory holder and the blade washer (Picture 3).
PICTURE 3
A. Accessory holder
B. Clamping screw
C. Hex key
D. Blade washer
E. Accessory
F. Accessory
G. Washer with bevel up
2. Clean accessory holder, accessory and the clamping screw
with a clean cloth.
3. Place the accessory onto the accessory holder making
sure the accessory engages all pins in the holder and the
accessory is flush against the accessory holder.
4. Securely tighten the clamping screw with the hex provided
(Picture 4).
PICTURE 4
A. Clamping screw
B. Hex key
NOTE: Some accessories, such as scrapers or blades, may be
mounted either straight on the tool, or at an angle to enhance
usability (Picture 5).
PICTURE 5
INSTALLING AND REMOVING ACCESSORIES
WITH QUICK LOCK™ ACCESSORY CHANGE
Model MM40
The Dremel Multi-Max MM40 includes an integrated accessory
change mechanism. The Quick Lock™ accessory interface allows
you to install and remove accessories without the need of a
wrench or hex key. You will also no longer need to worry about
losing a clamping screw & washer as these parts are no longer
used in the MM40 version of the Multi-Max.
1. To install an accessory using the Quick Lock™ feature, hold
tool upside down to prevent the blade from falling off the
accessory holder when installing and removing accessories.
2. Turn the Quick Lock™ lever on the top on the tool counter-
clockwise to unlock the clamping mechanism (Picture 6).
The lever needs to be fully engaged to unlock the clamping
mechanism.
PICTURE 6
A. Open
B. Close
3. Clean accessory holder, accessory and the clamping flange
with a clean cloth.
4. Place the accessory onto the accessory holder making
sure the accessory engages all pins in the holder and the
accessory is flush against the accessory holder (Picture 7 &
Picture 8).
10
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Dremel Model MM40 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Dremel Model MM40 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 10,44 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info