488595
23
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
23
When the indicator light stops “BLINKING” (and becomes a
steady green light) fast charging is complete. The battery pack is
fully charged and can be removed from the charger.
When you begin the charging process of the battery pack, a
steady green light could also mean the battery pack is too hot
or too cold.
Fast charging is only possible when the temperature range of
the battery pack is between 0°C and 45°C.
When needed, the internal fan of the charger will turn on to aid
the charging process and speed.
As soon as the battery pack reaches the correct temperature
range, the battery charger will automatically switch to fast
charging.
The battery pack may be used even though the light may still
be blinking. The light may require more time to stop blinking
depending on temperature.
The purpose of the green light is to indicate that the battery
pack is fast-charging. It does not indicate the exact point of full
charge. The light will stop blinking in less time if the battery
pack was not completely discharged.
If the green indicator light is “ON”, the battery pack cannot
accept a charge.
GENERAL
The Dremel multitool is a high quality precision tool that can
be used to perform detailed and intricate tasks. The wide range
of Dremel accessories and attachments allow you to perform
a large variety of tasks. These include tasks such as sanding,
carving, engraving, routing, cleaning and polishing.
PICTURE 1
A . Shaft lock button
B . On/Off switch
C . Hanger
D . Battery level indicator
E . Variable speed switch
F . Battery pack
G . Battery release tabs
H . Ventilation openings
I . Housing
J . Battery pack
K . Battery release tabs
L . Shaft
M . Housing Cap
N . Collet nut
O . Collet
P . Collet wrench
COLLETS
The Dremel accessories available for the multitool come
with various shank sizes. Four size collets are available to
accommodate the different shank sizes. Collet sizes are
identified by the rings on the back of the collet.
PICTURE 2
A . Collet nut
B . 3.2 mm Collet without ring (480)
C . 2.4 mm Collet with three rings (481)
D . 1.6 mm Collet with two rings (482)
E . 0.8 mm Collet with one ring (483)
F . Indentification rings
NOTE: Some multitool kits may not include all four collet sizes.
Collets are available separately.
Always use the collet that matches the shank size of the
accessory you plan to use. Do not force a larger diameter shank
into a smaller collet.
CHANGING COLLETS
PICTURE 3
A . Collet wrench
B . Shaft lock button
C . Collet nut
D . To loosen
E . To tighten
1 . Press the shaft lock button, hold down and rotate the shaft
by hand until it engages the shaft lock. Do not engage the
shaft lock button while multitool is running.
2 . With the shaft lock button engaged, loosen and remove the
collet nut. Use the collet wrench if necessary.
3 . Remove the collet by pulling it free from the shaft.
4 . Install the appropriate size collet fully into the shaft and
reinstall the collet nut finger tight. Do not fully tighten the
nut when there is no bit or accessory installed.
CHANGING ACCESSORIES
1 . Press the shaft lock button and rotate the shaft by hand
until it engages the shaft lock. Do not engage the shaft lock
button while multitool is running.
2 . With the shaft lock button engaged, loosen (do not remove)
the collet nut. Use the collet wrench if necessary.
3 . Insert the bit or accessory shank fully into the collet.
4 . With the shaft lock button engaged, finger tighten the collet
nut until the bit or accessory shank is gripped by the collet.
NOTE: Be sure to read the instructions supplied with your Dremel
accessory for further information on its use.
Use only Dremel tested, high performance accessories.
BALANCING ACCESSORIES
For precision work, it is important that all accessories be in good
balance (much the same as the tires on your automobile). To
true up or balance an accessory, slightly loosen collet nut and
give the accessory or collet a 1/4 turn. Re tighten collet nut and
run the Rotary Tool. You should be able to tell by the sound and
feel if your accessory is running in balance. Continue adjusting
in this fashion until best balance is achieved.
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Dremel 8200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Dremel 8200 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 6,92 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info