32309
17
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
17.
Maintaining Your Scroll Saw
FIG. 18
Maintenance
For your own safety, turn power switch
“OFF” and remove plug from the power
source outlet before maintaining or lubricating your Scroll
Saw.
GENERAL
Frequently blow out any dust that may accumulate inside
the motor.
An occasional coat of paste wax on the work table will
allow materials being cut to glide smoothly across the
work surface and deters rust.
Certain cleaning agents and solvents dam-
age plastic parts. Including: gasoline, car-
bon tetrachloride, chlorinated cleaning solvents, ammonia
and household detergents that contain ammonia. Avoiding
use of these and other types of cleaning agents minimizes
the probability of damage.
To avoid shock or fire hazard, if the power
cord is worn or cut, or damaged in any way,
have it replaced immediately.
All repairs, electrical or mechanical, should
be attempted only by trained repairmen.
Contact the nearest Dremel Factory Service Center, or
other competent repair service. Use only Dremel replace-
ment parts, any others may create a hazard.
Carbon Brushes
The brushes and commutator in your tool have been engi-
neered for many hours of dependable service. To maintain
peak efficiency of the motor, we recommend every two to six
months the brushes be examined. Only genuine Dremel
replacement brushes specially designed for your tool should
be used.
The brushes should be inspected frequently when tools are
used continuously. If your tool runs sporadically, loses
power, makes unusual noises or runs at a reduced speed,
check the brushes. To continue using the tool in this condi-
tion will permanently damage your tool.
With the cord unplugged, remove the brush caps one at a
time with a small screwdriver by rotating cap counter-clock-
wise and check each brush (Fig. 17).
If the brush is less than 1/8" long and the end surface of the
brush that contacts the commutator is rough and/or pitted,
they should be replaced. Check both brushes. Usually the
brushes will not wear out simultaneously. If one brush is
worn out, replace both brushes. Make sure the brushes are
installed as illustrated. The curved surface of the brush must
match the curvature of the commutator.
After replacing brushes the tool should be run at no-load;
place it on a clean surface and run it freely for 5 minutes
before loading (or using) the tool. This will allow the brushes
to “seat” properly and will give you more hours of life from
each set of brushes. This will also extend the total life of your
tool since the commutator surface will “wear” longer.
Lubrication
ARM BEARINGS
Lubricate the arm bearings with oil after 10 hours of use.
Re-oil after every 50 hours of use or whenever there is a
squeak coming from the bearings.
TO LUBRICATE
1. Turn saw on its side (Fig. 18).
2. Remove rubber plug to expose bronze bearing.
3. Squirt a generous amount of SAE 20 oil around the shaft
end and bronze bearing.
4. Let the oil soak in overnight in this condition.
5. Next day repeat the above procedure for the opposite
side of the saw.
CAUTION
!
WARNING
!
WARNING
!
FIG. 17
WARNING
!
BRUSH
CAP
BRUSH
SPRING
BRUSH
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Dremel 1680 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Dremel 1680 in de taal/talen: Engels, Frans, Spaans als bijlage per email.

De handleiding is 2,1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info