680255
19
Verklein
Vergroot
Pagina terug
1/129
Pagina verder
0. Preface ..................................................................... 0-1
0.1 About This Manual ........................................... 0-2
0.2 Copyright Declarations .................................. 0-2
0.3 Trademarks ........................................................ 0-2
0.4 How To Become A Registered Owner ........ 0-2
0.5 Safety Instructions ........................................... 0-3
0.6 Warranty .............................................................. 0-3
0.7 European Community Declarations ............ 0-4
1. Getting Started .................................................. 1-1
1.1 Introduction .......................................................... 1-2
1.2 Unpacking your Vigor2000 Router ................... 1-3
1.3 LED Indicators & Rear Panels .......................... 1-4
1.4 Key Features .......................................................... 1-7
2. Installation & Setup ......................................... 2-1
2.1 Before you Begin ................................................ 2-2
2.2 Hardware Installation ......................................... 2-4
2.3 Setting up a Management PC ........................... 2-7
2.4 Using the Smart Start Wizard ......................... 2-13
2.5 Using the Web Configurator .......................... 2-18
Table of Contents
3. Basic Setup & Internet Access .................. 3-1
3.1 Basic Setup .......................................................... 3-2
3.2 Internet Access Setup ....................................... 3-7
3.3 ISDN Dial-up Internet Access ......................... 3-9
3.4 IDSL Leased-Line .................................................3-12
3.5 DSL/Cable Modem Internet Access ............... 3-14
4. Remote Access .................................................... 4-1
4.1 Introduction to Remote Access ......................... 4-3
4.2 Remote Dial-in Access ........................................ 4-3
4.3 LAN-to-LAN Access ............................................. 4-7
5. Advanced Setup ................................................ 5-1
5.1 Enabling the Remote Activation Function .... 5-3
5.2 Call Control Setup ................................................ 5-4
5.3 Configuring the BOD Parameters ................... 5-5
5.4 NAT Setup ........................................................... 5-7
5.5 IP Filter/Firewall Setup ....................................... 5-10
6. Virtual TA Application .................................... 6-1
6.1 Virtual TA Concepts ............................................ 6-2
6.2 Installing a Virtual TA Client .............................. 6-4
6.3 Configuring a Virtual TA Client/Server ........... 6-5
7. System Management ...................................... 7-1
7.1 Online Status ........................................................ 7-3
7.2 Management Setup ............................................. 7-5
7.3 Diagnostic Tools .................................................. 7-7
7.4 Reboot System .................................................. 7-14
7.5 Firmware Upgrade ............................................ 7-15
8. Troubleshooting & FAQ ............................... 8-1
8.1 Using the Telnet Terminal Commands .......... 8-2
8.2 Viewing Call Logs ............................................... 8-4
8.3 Viewing ISDN Logs ............................................. 8-6
8.4 Viewing PPP Logs .............................................. 8-7
8.5 Viewing WAN Logs ............................................. 8-8
8.6 FAQs ........................................................................ 8-9
0-1
0
Preface
0.1 About This Manual
0.2 Copyright Declarations
0.3 Trademarks
0.4 How To Become A Registered Owner
0.5 Safety Instructions
0.6 Warranty
0.7 European Community Declarations
0-2
Preface
0.1 About This Manual
This manual is designed to assist users in using the DrayTek
Vigor2000 Router. Information in this document has been care-
fully checked for accuracy; however, no guarantee is given as
to the correctness of the contents. The information contained
in this document is subject to change without notice. Should
you have any inquiries, please feel free to contact
support@draytek.com.tw . For latest product info and features,
visit our website at www.draytek.com.tw.
0.2 Copyright Declarations
Copyright © 2000 DrayTek Corporation. All rights reserved. This
publication contains information that is protected by copyright.
No part may be reproduced, transmitted, transcribed, stored in
a retrieval system, or translated into any language without writ-
ten permission from the copyright holders.
0.3 Trademarks
Microsoft is a registered trademark of Microsoft Corp. Windows,
Windows 95, 98, Me, NT, and 2000 are trademarks of Microsoft
Corp. Other trademarks and registered trademarks of products
referred to in this manual are the properties of their respective
owners.
0.4 How To Become A Registered Owner
Web registration is preferred. Please visit the following website:
http://www.draytek.com.tw/registration.htm. Alternatively, fill in
the registration card and mail it to the address found on the
reverse side of the card. Registered owners will receive future
product and update information.
0-3
Preface
0.5 Safety Instructions
! Please read the installation guide thoroughly before you set
up the router.
! The router can be used only with a BRI (Basic Rate Inter-
face) ISDN line.
! The router is a complicated electronic unit that may be
repaired only by authorized and qualified personnel. Do not try
to open or repair the router yourself.
! Do not place the router in a damp or humid place, e.g. a
bathroom.
! The router should be used in a sheltered area, within a
temperature range of +5 to +40 Celsius.
! Do not expose the router to direct sunlight or other heat
sources. The housing and electronic components may be dam-
aged by direct sunlight or heat sources.
! Keep the packaging out of reach of children.
! When you want to dispose the router, please follow local
regulations on conservation of the environment.
We warrant to the original end user (purchaser) that the Vigor2000
Routers will be free from any defects in workmanship or materials
for a period of two (2) years from the date of purchase from the
dealer. Please keep your purchase receipt in a safe place as it
serves as proof of date of purchase.
During the warranty period, and upon proof of purchase, should
the product have indications of failure due to faulty workman-
ship and/or materials, we will, at our discretion, repair or replace
the defective products or components, without charge for either
parts or labor, to whatever extent we deem necessary to re-
store the product to proper operating condition. Any replace-
ment will consist of a new or re-manufactured functionally equiva-
0.6 Warranty
0-4
Preface
lent product of equal value, and will be offered solely at our
discretion. This warranty will not apply if the product is modi-
fied, misused, tampered with, damaged by an act of God, or
subjected to abnormal working conditions.
The warranty does not cover the bundled or licensed soft-
ware of other vendors. Defects that do not significantly affect
the usability of the product will not be covered by the warranty.
We reserve the right to revise the manual and online documen-
tation and to make changes from time to time in the contents
hereby without obligation to notify any person of such revision
or changes.
0.7 European Community Declarations
The Vigor2000 Routers have been approved for connection to
the Public Switched Telecommunication Network using inter-
faces compatible with ITU-TSS recommendation I.430 (Basic
Rate ISDN user access). The Vigor2000 Routers comply with
the R&TTE Directive 99/5/EC.
1-1
1
Getting Started
1.1 Introduction
1.2 Unpacking Your Vigor2000 Router
1.3 Front Panel& Rear Panel Descriptions
1.4 Key Features
1-2
Getting Started
1.1 Introduction
The Vigor2000 Router provides multiple users with efficient and reli-
able access over a single ISDN BRI, IDSL (U Interface), DSL line, or
Cable Modem (not support Dynamic IP) service to the Internet and
corporate LAN for using E-mail, sharing documents, Web surfing, file
transfers, etc. Moreover, the provision of a built-in six-port 10BaseT
Ethernet hub and one Uplink port may give cost-effective workgroup
connectivity over Ethernet.
In addition to improving the productivity of employee, flexible
telecommuting access, and affordable management cost, Vigor2000
Router accommodates room for business growth from 6-7 computers
to more. The smart solution of DrayTek Vigor2000 Route provides
SOHO users an `easy to setup and use`, `instant internet and intranet
connection`, `high interoperablility`, and `good security` for network
management.
The broadband access protocol supports PPPoE, PPTP, and Static
IP. These protocols comply with worldwide Ethernet-based DSL/Cable
Modem standards.
For traditional ISDN users, the Vigor2000 Router features a built-in
Virtual TA (Remote CAPI) server which operates as a CAPI-based
ISDN TA for LAN users. To run FAX transmission or data transfer serv-
ices, users need to install a Virtual TA client driver on the PCs and
use third-party CAPI-based software .
Vigor2000 Router provides seamless migration from ISDN to a
broadband connection for multiple SOHO users and easy usage of
ISDN for backup-dial and/or remote access while concurrently using
the DSL/Cable modem connection.
PPPoE / PPTP allows users on the LAN interface to setup a dial-on-
demand DSL connection sharing the same IP account, and paying for
only ONE connection. The idle-timeout function prevents wasted
connection charges by shutting down the connection when it is idle.
No PPPoE / PPTP client software is required for the computers. Hassle
free!
1-3
Getting Started
1.2 Unpacking Your Vigor2000 Router
Your Vigor2000 Router package should contain items listed below. If
any item is missing or damaged, contact your dealer or DrayTek
Customer Service Department immediately.
! One User manual with warranty/registration card
! One CD-ROM, including User Manual in electronic form, latest
released firmware, and utilities
! One RJ-45 ISDN telephone cable (black)
! One AC/AC power adapter (black)
! One Console cable (gray)
! One RJ45 to RS232 (9 pin) converter for console cable
! One Ethernet LAN cable (blue) for connection to a computer
or hub
Dimensions (cm) of Vigor2000 Router
21.8 (L) x 15.8 (W) x 3.6 (H)
Weight: 399 grams
Maximum Power: 10W
Power Adapter: AC adapter; Class2 transformer; input is 230VAC 50Hz;
minimum output is from 15 to 17V AC 600mA
1-4
Getting Started
1.3 Front Panel & Rear Panel Descriptions
Vigor2000 Router:
Front Panel Description -- LED Indicators
There are eleven LEDs on the front panel, including ACT, LNK,B1, B2,
COL, and P1 ~ P6.
ACT (Activity)
BLINK when power is supplied to the router and the router is running
normally.
1-5
Getting Started
ISDN Group:
Note:
On some NT1 boxes, the LNK LED will go OFF when the
ISDN line has been idle for a while. When the router is
dialing or answering a call, it should be ON again.
LNK (Link)
ON when the connected network card or hub has linked up.
Blinking when the Ethernet packets pass through the interface.
B1
ON when there is successful remote connection on the ISDN BRI B1
channel.
B2
ON when there is successful remote connection on the ISDN BRI B2
channel.
LAN Group:
Col (Collision)
BLINK when there is collision of packets within the Ethernet.
P1 ~ P6
- ON when the computer is connected and has no packet transmission
going.
- BLINK when packets are sending/receiving through hub or connected
computer.
Rear Panel Description
The Vigor2000 has a power jack, an uplink port, six RJ-45 ports, a
console port, and an ISDN port on the rear panel:
1-6
Getting Started
Only the DrayTek supplied power adapter should be connected to the
power jack.
UPLINK (back panel)
Use attached 10BaseT LAN cable to connect to another hub. The light
besides the port will be ON when the router is connected to another
hub.
LAN - P1, P2, P3, P4, P5, P6
These switch ports should be connected to your local PCs.
CONSOLE
Connects to the computer you want to use to configure Vigor2000
Router.
ISDN (Varied by Router Model)
- For S/T Interface Router Model: Connects to a NT1 box provided by
your ISDN service provider.
- For U Interface Router Model: If your ISDN service provider does not
provide the NT1 box or your ISP provides IDSL connection, use this
model for connection.
1-7
Getting Started
1.4 Key Features
The Vigor2000 Router provides many built-in server and software fea-
tures to provide a convenient comprehensive solution for your SOHO
network.
1. Network Address Translation (NAT): NAT allows multiple SOHO
users to concurrently connect to an Internet Service Provider (ISP)
using a single Internet access account.
2. Firmware Upgrade (TFTP) Server: Using this server and the
Firmware Upgrade Utility software, you may easily upgrade to the
latest firmware whenever enhanced features are added.
3. Web (HTTP) Server: A Web browser is the most common tool
used to surf the Internet. You may use Microsoft Internet Explorer
or Netscapes browser etc, to configure the Vigor2000 Router as easily
as surfing web sites.
4. Virtual TA Server (VTA): The terminology Virtual TA means the
Vigor2000 can operate as traditional ISDN TA to transmit and
receive data, FAX, and voice transmissions via third-party software running
on a desktop computer. In fact, a virtual TA server works as a network
TA to exchange packets between an ISDN BRI and an Ethernet LAN.
Therefore, desktop computers can use the ISDN line resource via an
Ethernet LAN. In short, multiple users can share a network TA for
backward compatibility with traditional applications, such as BBS, file
transfer, sending/receiving FAXs etc.
5. Remote Access Server (RAS): RAS provides remote dial-in ac-
cess services for home workers, branch offices, or telecommuters.
Vigor2000 Routers offer 10 dial-in user profiles, including an
authentication mechanism through CHAP/PAP and Calling Line
Identification (CLID), secure callback functions, and 16 Lan-to-Lan Dialer
Profiles, etc.
6. Routing Information Protocol (RIP) Support: Used in most
1-8
Getting Started
LAN-to-LAN applications. The RIP protocol exchanges routing infor-
mation between routers.
7. Domain Name Server (DNS) Proxy: The DNS proxy maintains a
DNS cache, including a mapping table between domain names and IP
addresses. The proxy also remembers DNS query packets sent
through the router and saves them into its own DNS cache. For
enhanced speed, when a DNS query packet enters the router, the
proxy searches its local DNS cache. If matched, the router sends an
answer to the host that sent the DNS query packet. Only unmatched
DNS queries require querying a WAN Domain Name Server.
8. Telnet Terminal Server: The Telnet User Interface (TUI) is an
efficient method of configuring and managing routers. It utilizes a
traditional command-line user interface and is mainly for advanced
configuration, management, and troubleshooting.
9. Dynamic Host Configuration Protocol (DHCP) Server: The server
provides an easy-to-configure function for your local IP network. It can
automatically assign IP network configurations for local PCs, such as
IP address, IP netmask, gateway IP address, and Domain Name server
etc.
10. Built-in Flash ROM: The Flash ROM memory saves the router
firmware and configurations, even after power down.
11. ISDN Digital Subscriber Line (IDSL) Client Support: If your
ISP provides ISDL connection, you can use the router to connect at
64/128k bps (U Interface Leased Line Type only).
12. Point-to-Point over Ethernet (PPPoE) Client Support: If you
are a DSL user, the router has a built-in PPPoE client for establishing
a DSL link connection with the ISP. There is no need to install a
further PPPoE driver on your computers.
13. Point-to-Ponit Tunnelling Protocol (PPTP) Client Support:
Some DSL modems (e.g. Alcatel modems) only provide a PPTP local
connection for an end user computer. The Vigor2000 Routers have a
1-9
Getting Started
built-in PPTP client for establishing a DSL link transport protocol for
your entire local network. There is no need to install a PPTP driver on
your computers.
14. Firewall: In addition to the built-in NAT mechanism, the Vigor2000
Routers feature another powerful firewall to protect your local network,
or to deny specified local users access to unauthorized network
services.
15. Bandwidth-on-Demand (BOD) for ISDN Interface: As the ISDN
BRI interface has two independent B channels, the BOD mechanism
allows you to automatically add/drop a B channel according to data
traffic throughput.
16. Remote Management: The system manager can remotely
manage the routers through an ISDN remote dial-in, ISDN, or DSL
WAN interface.
2-1
2
Installation &
Setup
2.1 Before you Begin
2.2 Hardware Installation
2.3 Setting up a Management PC
2.4 Using the Smart Start Wizard
2.5 Using the Web Configurator
2-2
Installation & Setup
2.1 Before You Begin
1. Use only the power adapter supplied by DrayTek Corp. Using an
incorrectly rated power adapter will result in damage to the router.
2. Know the type of interface provided by your ISP or telecom. The
standard model only supports the ISDN BRI S/T-interface. If you are
an ISDN U-interface user, you need to order a U-interface model. If
you are an ISDN S/T-interface user, you should have an NT-1 or NT-1
plus provided by your ISP or telecom. Also, make sure the ISDN
line is available.
3. In case of emergency, unplug the power adapter first.
4. Locate the device in a clean location. Do not block the ventilating
slots on the rear panel.
5. Cables must be attached to the correct ports; to do otherwise
may result in damage to the router. Keep cables away from
walkways.
6. If you use S/T-interface, do not extend the ISDN line greater than
100 meters from the NT-1 (NT-1 plus) box and the router.
7. If you use DSL/Cable, check that your subscribed DSL/Cable
modem supports the Ethernet interface for connecting to your PC.
If not, you will be unable to connect it to the router.
8. Before you set up the router, you need to know the default
settings of Vigor2000 Router as shown below:-
Factory Default Settings:
Default IP Network Settings:
IP Address: 192.168.1.1
2-3
Installation & Setup
Subnet Mask: 255.255.255.0
DHCP Server: Enabled
Start IP Address: 192.168.1.10
IP Pool Counts: 50
DNS Server IP Address
- Primary IP Address: empty
- Secondary IP Address: empty
Web Configurator:
Username: admin
- Password: <blank>
Note: Blank means no password required.
Telnet Console:
Password: <blank>
Note: Blank means no password required.
Management from the Internet: Not allowed
Virtual TA Server: Enabled
Remote Dial-In Server: Disable
IP Address Assignment for Dial-In User: 192.168.1.200
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Draytek Vigor 2000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Draytek Vigor 2000 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info