784270
12
Verklein
Vergroot
Pagina terug
1/76
Pagina verder
12
If you must power more than one device
with one power supply , we recommend
to use a PoE-Switch with PoE Standard
IEEE 802.3af Mode A or an appropriate
DIN rail power supply (see “OPTION 3”).
Theoretically (not recommended by us!),
an unshielded, but over the whole length
(max. 80 m/262 ft) twisted bell wire with
two pairs of wires (first twisted pair of
wires: “T+, T-”, second twisted pair of wires
“R+, R-”) can be used for the network
and PoE transmission as an alternative
to a Cat.5 network cable or better. This is
comparable to a Cat.3 network cable. In
this case, however, we cannot guarantee
the data throughput or the stability of
the network connection and power sup-
ply; this must be measured and checked
on site by qualified personnel over several
hours (network data is transmitted at
high frequency, therefore a shielded Cat.5
network cable twisted in pairs or better
must normally be used).
device or cause poor transmission quality. The warranty automatically
expires if you use a different power supply unit.
NOTICE The power supply unit is plugged into a wall socket inside your
house, usually where the two wires from your assembly location
come out of the wall in the interior of the house.
The provided mains adapter is not outdoor-ready and for
indoor-use only.
OPTION 
Power supply and network connection using PoE
(Power over Ethernet)
To power the device via a PoE-Switch (e.g. D-Link DGS-1008P) or PoE-
Injector (e.g. DoorBird Gigabit PoE Injector A1091), use a CAT.5 cable or
higher in accordance with the PoE standard IEEE 802.3af Mode A.
A CAT.5 cable or higher must be used for this purpose, as network signals
can only be transmitted over completely insulated, shielded and twisted
cables. If you use PoE as a source of power, the four wires for PoE then
simultaneously form the data line. The device will not start if your PoE-
Switch/PoE-Injector does not support the PoE Standard IEEE 802.3af
Mode A.
NOTICE Do not combine the power supply from the power supply unit
(mains adapter) with the power supply via PoE.
You can find further information about PoE here: http://www.doorbird.
com/poe
1. Disconnect the PoE-Switch or PoE-Injector from the power grid.
2. Place the network cable in the installation site of the device.
OPTION 
Power supply using a DIN rail power supply unit
Alternatively to the mains adapter, we offer DIN rail power supplies in
our online shop, which can be installed by a specialist. The network
connection is then made via a network cable or alternatively via WiFi.
CONNECTING THE DEVICE
It is possible to connect the cables and wires to the device conveniently
and safely via the labeled screw connection terminal. You can connect all
necessary cables and wires to the device now.
NOTICE Please remove any cables and wires from the connection ports
of the device that you do not need.
For easier installation we strongly recom-
mend to remove the plug from screw
connection terminal while you connect
the cables and wires.
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Doorbird D1102V bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Doorbird D1102V in de taal/talen: Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 13.29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Doorbird D1102V

Doorbird D1102V Aanvulling / aanpassing - Alle talen - 1 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info