629513
6
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
Mounting the Display Elite Control Operations Manual
4 L-2230 ENGLISH
MOUNTING THE DISPLAY
1. Make the cut-out for the display panel. Cut-out size is 3-5/16” (8.41cm) wide by 2-3/16” (5.56cm) high.
2. Plug one end of the display cable (8-pin connector) into the upper-right socket on the circuit board in the electric box
and the other end into the back of the display panel.
3. Secure the display panel to the bulkhead using the four screws provided. Do not use a screw gun and do not over-
tighten screws when mounting, because either method may damage the display.
4. When the display is securely mounted, mount the bezel over the display frame until it snaps into place.
MOUNTING THE OPTIONAL SENSORS
REMOTE AIR SENSOR
Install the optional remote air sensor if the display can not be mounted in a proper location for accurately sensing room
temperature. Installing the remote air sensor overrides the display’s built-in sensor. The standard cable length for the remote air
sensor is 7 feet (2.1m).
1. Mount the remote air sensor in the return-air stream behind the opening of the return-air grille.
2. Plug its cable (6-pin connector) into the “ALT AIR” socket #J4 in the upper-left corner of the circuit board.
OUTSIDE AIR TEMPERATURE SENSOR
Install the optional outside air temperature sensor to monitor the temperature outside the cabin. Outside air sensor cables are
available in various lengths.
1. Mount the sensor outside but not in direct sunlight.
2. Plug its cable into the “OAT” socket #J3.
SERVICE SENSOR
Install the optional condenser coil temperature sensor into the “SERVICE/H2O” socket #J5. Use of this sensor must be enabled
via program parameter P-8, the Pump Sentry feature. See “P-8: Optional Pump Sentry” on page 9 for details.
OPERATION
OPERATOR CONTROLS AND DISPLAY PANEL
Refer to Figure 1, page 2 for the button locations and display functions listed below.
DISPLAY INDICATORS
Auto Mode Indicator - The Auto Mode LED lights when the system is in Automatic Mode, which switches to cooling or
heating as required to satisfy the temperature set point.
Cool Mode Indicator - The Cool Mode LED lights when the cool-only mode is selected or when the unit is in an
Automatic Mode cooling cycle.
Heat Mode Indicator - The Heat Mode LED lights when the heat-only mode is selected or when the unit is in an
Automatic Mode heating cycle.
Moisture Mode Indicator - The Moisture Mode LED lights when the Moisture Mode is selected. This mode controls
humidity during periods when the vessel is unoccupied.
IMPORTANT
The system’s air sensor is located in the control’s display panel, therefore the display MUST be located on an interior
wall at eye level. It must NOT be located in direct sunlight or inside a cabinet.
If these conditions cannot be met, you must purchase the Optional Remote Air Sensor and install it in the return-air
stream.
NOTE
Do not staple any sensor cables when mounting.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Dometic Elite Control DX systems bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Dometic Elite Control DX systems in de taal/talen: Engels als bijlage per email.

De handleiding is 0,32 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info