507712
6
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
6
Cutoff discs
The protection hood must always be on! Change discs only with the engine -
off!
There are two basic types of cutoff discs: -
For metal (hot cutting) -
For masonry (cold cutting) -
NOTE:
When using diamond cutoff discs, always make sure to observe the “direction of
rotation” markings. Diamond discs should only be used for cutting masonry/brick/
concrete etc.
Cutoff discs are intended only for radial loading, i.e. for cutting. -
Do not grind with the sides of the cutting disc! This will break the disc (10)!
CAUTION:
Never change direction (turning radius less than 5 meters / 5 1/2 yards), exert
lateral (sideways) pressure, or tip the Power Cutter during cutting (11)!
Use a cutting disc only for cutting the materials it is intended for. The proper type -
of disc must be used, for either metals or masonry.
The arbour hole (bore) of the cutting disc must t the shaft exactly. If the arbour -
hole is larger than the shaft diameter, a spacer ring must be used (accessories).
Use only cutting wheels approved by the DSA (German Abrasive Disc -
Committee) or equivalent organisation for freehand cutting at up to 4,370 RPM
(= 80 m/sec. at circumference) for 14”/355 mm discs, or up to 5,100 RPM
(= 80 m/sec. at circumference) for 12”/300 mm discs.
The disc must be free of defects (12). Do not use defective cutting discs. -
Always tighten the cutting disc mounting bolt to a torque of 30 Nm.
Otherwise, the cutting disc can twist.
Before starting the cutting disc, make sure you have a steady footing. -
Put the Power Cutter into operation only as described in this instruction manual -
(13). Always place your left foot in the rear handle and grasp the other handle
rmly (with thumb and ngers). Other starting methods are not allowed.
When starting the Power Cutter it must be well supported and securely held. The -
cutting disc must not be touching anything.
If the cutting disc is new, test it by running it at least 60 seconds at top speed. -
When doing this, make sure that no persons or body parts are in the extended
swing range of the disc, in case it is defective and ies apart.
When working with the Power Cutter always hold it with both hands. - Take
the back handle with the right hand and the tubular handle with the left hand.
Hold the handles tightly with your thumbs facing your ngers.
CAUTION: When you release the throttle lever the disc will keep spinning -
for a short period of time (free-wheeling effect).
Continuously ensure that you have a safe footing. -
Hold the Power Cutter such that you will not breathe in the exhaust gas. Do not -
work in closed rooms or in deep holes or ditches (danger of poisoning by fumes).
Switch off the Power Cutter immediately if you observe any changes in its -
operating behavior.
Switch off the engine before inspecting the V-belt tension or tightening it, -
replacing the cutting wheel, repositioning the cutter attachment (side or
middle position) or eliminating faults (14).
Turn off the engine immediately and check the disc if you hear or feel any change -
in cutting behaviour.
Turn off the Power Cutter when taking a break or stopping work (14). Place the -
unit in such a way that the disc is not touching anything and cannot endanger
anyone.
Do not put the overheated Power Cutter in dry grass or on any inammable -
objects. The mufer is very hot (danger of re).
IMPORTANT: - After wet cutting, rst turn off the water feed and then let the disc
run at least 30 seconds, to ing off the remaining water and prevent corrosion.
10
11
12
13
14
min. 5 m
Maintenance
Refuelling
Changing cutoff discs
Repositioning the
cutting attachment
Stopping work
Transport
Putting out of
function
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Dolmar PC-7614V bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Dolmar PC-7614V in de taal/talen: Nederlands, Engels als bijlage per email.

De handleiding is 4,22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info