Handleiding Dolmar AH-1853H (pagina 9 van 64) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens)

598393

Verklein

Vergroot

Pagina terug

1/64

Pagina verder

Attaching the chip receiver (optional accessory) on the

tool when trimming the hedge straight can avoid cut off

leaves’ being thrown away. (Fig. 10)

To cut a hedge side evenly, it helps to cut from the bottom

upwards. (Fig. 11)

Trim boxwood or rhododendron from the base toward the

top for a nice appearance and good job.

Installing or removing chip receiver

(optional accessory)

CAUTION:

• Always be sure that the tool is switched off and

unplugged before installing or removing chip receiver.

NOTE:

• When replacing the chip receiver, always wear gloves

so that hands and face does not directly contact the

blade. Failure to do so may cause personal injury.

• Always be sure to remove the blade cover before

installing the chip receiver.

• The chip receiver receives cut-off leaves and alleviates

collecting thrown-away leaves. This can be installed on

either side of the tool. (Fig. 12)

Press the chip receiver on the shear blades so that its slits

overlap with the nuts on the shear blades. (Fig. 13)

At this time, the chip receiver needs to be installed so that

its hooks fit into grooves in the shear blade unit. (Fig. 14)

To remove the chip receiver, press its lever on both sides

so that the hooks are unlocked.

CAUTION:

• The blade cover (standard equipment) cannot be

installed on the tool with the chip receiver being

installed. Before carrying or storing, uninstall the chip

receiver and then install the blade cover to avoid blade

exposure.

NOTE:

• Check the chip receiver for secure installment before

use.

• Never try to uninstall the chip receiver by an excessive

force with its hooks locked in the blade unit grooves.

Using the excessive force may damage it.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

Cleaning the tool

Clean out the tool by wiping off dust with a dry or soap-

dipped rag.

CAUTION:

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Blade maintenance

Smear the blade before and once per hour during

operation using machine oil or the like.

NOTE:

• Before smearing the blade, remove the chip receiver.

After operation, remove dust from both sides of the blade

with wired brush, wipe it off with a rag and then apply

enough low-viscosity oil, such as machine oil etc. and

spray-type lubricating oil.

CAUTION:

• Do not wash the blades in water. Failure to do so may

cause rust or damage on the tool.

Removing or installing shear blade

CAUTION:

• Before removing or installing shear blade, always be

sure that the tool is switched off and the battery

cartridge is removed.

• When replacing the shear blade, always wear gloves

without removing blade cover so that hands and face

does not directly contact the blade. Failure to do so

may cause personal injury.

NOTE:

• Do not wipe off grease from the gear and crank. Failure

to do so may cause damage to the tool.

Removing the shear blades (Fig. 15)

Reverse the tool and loosen four screws and remove the

under cover.

NOTE:

• Be careful not to get your hands dirty as grease is

applied in the shear blade driving area. (Fig. 16)

Loosen four screws and remove the blades. Remove the

washer and sponge from the shear blades and put them

aside. They are required for the later installation. (Fig. 17)

If the sleeves are still left in the holes of the gear, remove

the gear and push the sleeves out of it with a screwdriver

or the like.

NOTE:

The washer underneath the gear may come off by

mistake when removing the gear. In this case, return it to

the original position as it was installed.

Installing the shear blade (Fig. 18)

Remove the blade cover from the old shear blades and fit

it onto the new ones to avoid contact with blades.

(Fig. 19)

Adjust the hole positions by turning the gear as illustrated.

(Fig. 20 & 21)

Apply some grease provided with the new shear blades

as illustrated. (Fig. 22)

Put the removed sponge in the same position as the old

one. Make sure that the sleeves provided with the new

shear blades are put on the pins of the blade. Place the

new shear blades on the tool so that the pins fit in the

holes of the gear. If the sleeves on the pins come off

mistakenly, put them into the holes of the gear

beforehand. (Fig. 23)

Install the blade and tighten the four screws and put the

removed washer in the same position as the old one.

(Fig. 24)

Install the under cover on the tool and tighten the four

screws firmly.

Storage

The hook hole in the tool bottom is convenient for hanging

the tool from a nail or screw on the wall. (Fig. 25)

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Dolmar AH-1853H Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info