Handleiding Directed Electronics Merlin 3000 (pagina 34 van 38) (Engels)

583777

Verklein

Vergroot

Pagina terug

1/38

Pagina verder

3000

OOwwnneerr’’ss GGuuiiddee

limited lifetime consumer warranty

For a period of one calendar year from the date of purchase of this auto-security device,

Directed Electronics promises to the ORIGINAL PURCHASER to repair or replace (with a com-

parable reconditioned model), free of cost, any electronic control module which proves to be

defective in workmanship or material under normal use, SO LONG AS THE SYSTEM WAS SOLD,

INSTALLED, AND SERVICED BY A PROFESSIONAL AUTO INSTALLER, AND REMAINS IN THE CAR

IN WHICH THE SYSTEM WAS ORIGINALLY INSTALLED. If warranty service is necessary you must

have a clear copy of your sales receipt containing all of the information shown on the follow-

ing page.

After the first calendar year, from the date of purchase of this auto-security device, Directed

Electronics promises to the ORIGINAL PURCHASER to repair or replace (with a comparable

reconditioned model) any electronic control module which proves to be defective in work-

manship or material under normal use FOR A CHARGE OF $45.00, SO LONG AS THE SYSTEM

WAS SOLD, INSTALLED, AND SERVICED BY A PROFESSIONAL AUTO INSTALLER, AND REMAINS

IN THE CAR IN WHICH THE SYSTEM WAS ORIGINALLY INSTALLED. If warranty service is neces-

sary you must have a clear copy of your sales receipt containing all of the information shown

on the following page.

This warranty contains the entire agreement relating to warranty and supersedes all previous

and contemporaneous representations or understandings, whether written or oral. IN ANY

EVENT, DIRECTED ELECTRONICS IS NOT LIABLE FOR THE THEFT OF THE VEHICLE AND/OR ITS

CONTENTS. This warranty is void if the product has been damaged by accident, unreasonable

use, neglect, improper service or other causes not arising out of defects in materials or con-

struction. This warranty is nontransferable and does not apply to any unit that has been mod-

ified or used in a manner contrary to its intended purpose and does not cover batteries. The

unit in question must be returned to the manufacturer, postage prepaid. This warranty does

not cover labor costs for the removal, diagnosis, troubleshooting or reinstallation of the unit.

For service on an out-of-warranty product a flat rate fee by model is charged. Contact your

authorized dealer to obtain the service charge for your unit.

These systems are a deterrent against possible theft. Directed Electronics is not offering a guar-

antee or insuring against the theft of the automobile or its contents and disclaims any liability

for the theft of the vehicle and/or its contents. Directed Electronics does not authorize any per-

son to create for it any other obligation or liability in connection with this security system.

TO THE MAXIMUM EXTENT ALLOWED BY LAW, ANY AND ALL WARRANTIES ARE EXCLUDED

BY THE MANUFACTURER AND EACH ENTITY PARTICIPATING IN THE STREAM OF COMMERCE

THEREWITH. THIS EXCLUSION INCLUDES BUT IS NOT LIMITED TO THE EXCLUSION OF ANY

AND ALL WARRANTY OF MERCHANTABILITY AND/OR ANY AND ALL WARRANTY OF FITNESS

FOR A PARTICULAR PURPOSE AND/OR ANY AND ALL WARRANTY OF NON-INFRINGEMENT OF

PATENTS, IN THE UNITED STATES OF AMERICA AND/OR ABROAD. NEITHER THE MANUFAC-

TURER OR ANY ENTITIES CONNECTED THEREWITH SHALL BE RESPONSIBLE OR LIABLE FOR

ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL

DAMAGES, INCIDENTAL DAMAGES, TOWING, REPAIR, REPLACEMENT, DAMAGES FOR LOSS

OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND

THE LIKE. NOTWITHSTANDING THE ABOVE, MANUFACTURER DOES OFFER A LIMITED WAR-

RANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE. Some states

do not allow limitations on how long an implied warranty will last or the exclusion or limita-

tion of incidental or consequential damages. This warranty gives you specific legal rights, and

you may also have other rights which vary from state to state.

IMPORTANT NOTE:

This product warranty is automatically void if its date code or serial number is defaced, miss-

ing, or altered. This warranty will not be valid unless you have completed the warranty card

and mailed it to Directed Electronics within 10 days after purchase to the address listed on the

warranty registration card.

Make sure you have all of the following information from your dealer:

A clear copy of the sales receipt, showing the following:

Date of purchase

Your full name and address

Authorised dealer's company name and address

Type of alarm installed

Year, make, model and colour of the vehicle

Vehicle registration number

Vehicle identification number

All security options installed on vehicle

Installation receipts

trademarks and copyrights

Bitwriter

, Clifford

, Code-Hopping

, Directed

, Doubleguard

, ESP

, FailSafe

, Ghost Switch

™

Learn Routine

™

, Nite-Lite

, Nuisance Prevention

Circuitry, NPC

, Revenger

, Silent Mode

™

, Soft

Chirp

, Stealth Coding

™

, Stinger

, Valet

, Vehicle Recovery System

, VRS

, and Warn Away

are all Trademarks or Registered Trademarks of Directed Electronics.

limited lifetime consumer

warranty . . . . . . . . . . . . . . . . . . . . .i

trademarks and copyrights . . . . .ii

table of contents . . . . . . . . . . . . .1

what is included . . . . . . . . . . . . . .2

important information . . . . . . . . .2

your warranty . . . . . . . . . . . . .3

remote configurations . . . . . . . . .4

standard configuration for

in-key 2-button remote . . . . . .5

standard configuration for

3-button remote . . . . . . . . . . .5

using your system . . . . . . . . . . . . .6

arming . . . . . . . . . . . . . . . . . . .6

disarming . . . . . . . . . . . . . . . . .8

disarming without a remote . . .8

auto-immobilisation . . . . . . . . .9

remote siren silencing . . . . . . .9

remote chirp muting

(3-button remote only) . . . . . .10

remote sensor disable . . . . . .11

remote start sensor bypass . . .11

auxiliary channel bypass . . . . .12

valet mode . . . . . . . . . . . . . . .12

remote valet mode . . . . . . . . .13

instant auto-arming bypass . .14

nuisance prevention® circuitry 14

multiple event total recall . . . .15

battery back-up siren . . . . . . . . .15

diagnostics . . . . . . . . . . . . . . . . . .16

arming diagnostics . . . . . . . . .16

disarming diagnostics . . . . . . .17

arm/disarm diagnostic chart . .17

table of zones . . . . . . . . . . . .18

high frequency . . . . . . . . . . . . . .19

rapid resume logic . . . . . . . . . . .19

power saver mode . . . . . . . . . . .20

system sensors and adjustments 20

programming options . . . . . . . .21

manual programming

instructions . . . . . . . . . . . . . .22

user selectable features . . . . .24

user selectable features

descriptions - column one . . .24

user selectable features

descriptions - column two . . .26

user selectable features

descriptions - column three . .27

pin programming . . . . . . . . . .29

glossary of terms . . . . . . . . . . . . .31

security & convenience

expansions . . . . . . . . . . . . . . . . . .32

quick reference guide . . . . . . . .33

table of contents

what is included

One control module/siren with built-in Tilt sensor and 24 pin

main wiring harness (attached)

One Mini-Blue status LED

One 2-button Valet switch

One in-key 2-button remote

One 3-button remote

Two Merlin decal’s

This Owner’s Guide

Warranty Card

important information

Congratulations on the purchase of your state-of-the-art motorcycle

security system. It has been designed to provide years of trouble-free

operation. This system must be installed by an authorised dealer.

Installation of this product by anyone other than an authorised dealer

voids the warranty. As verification of authorization, all authorised deal-

ers are provided with preprinted dealer certificates.

In order to maximize the use of this system, please review this owner's

guide carefully prior to using your system. You can print additional or

replacement copies of this owner’s guide by accessing the Directed

website at www.directed.com.

nnoottee::

Your system MUST be installed by an Authorised dealer in accor-

dance with the instructions we supply them. The Merlin 3000 system

is designed to be installed on any 12-volt, negative ground motorcy-

cle or moped.

system maintenance

The system requires no specific maintenance. The batteries in your

remotes will last approximately one year under normal use. Your 3-but-

ton remote is powered by a miniature 3V lithium battery (CR2032). Your

in-key 2-button remote is powered by a 12V miniature battery (type

27A).

your warranty

It is necessary to retain your sales receipt, which reflects that the prod-

uct was installed by an authorised dealer. For full details regarding your

warranty coverage, please refer to the consumer warranty section of

this guide.

nnoottee::

Other than the remote controls, this system has no user-service-

able parts. Your authorized dealer can correct any system wiring prob-

lems and, if needed, can return any malfunctioning component to

Directed Electronics for repair/replacement under the terms of the

Limited Lifetime Warranty printed at the beginning of this guide.

remote configurations

The 3000 system has an in-key 2-button remote control and a 3-button

remote control. Two additional Merlin remote controls can be added.

3-BUTTON REMOTE CONTROL

RM/DISARM/PANIC

LED

SILENT ARM/DISARM

ACCESSORY

FRONT REAR

LED

RM/DISARM/PANIC

ACCESSORY

IN-KEY 2-BUTTON REMOTE CONTROL

remote functions

This system uses computer-based code learning to learn the remote

buttons. This makes it possible to assign any remote button to any sys-

tem function. The remotes initially come programmed with standard

configuration. The buttons in all of the instructions in this manual cor-

respond to a standard configuration remote.

standard configuration for in-key 2-button remote

Button

The arming, disarming, and panic functions are controlled by this button.

Button

An optional accessory convenience or expansion function that you have

added to your system can be activated by pressing this button.

and Buttons

When pressed together, these buttons disable the on-board control

module tilt sensor and any optionally installed sensors.

standard configuration for 3-button remote

Button

The arming, disarming, and panic functions are controlled by this button.

Button

An optional accessory convenience or expansion function that you have

added to your system can be activated by pressing this button.

Button

Silent arm and disarm is controlled by this button.

and Buttons

When pressed together, these buttons disable the on-board control

module tilt sensor and any optionally installed sensors.

and Buttons

Remotely enters or exits Valet.

using your system

The buttons used in the instructions in this manual correspond to the

standard remote configuration. If your remote has been custom con-

figured, the icons on your remote buttons may not correspond to the

indicated functions.

arming

You can activate, or arm, the system by pressing on your remote

for one second. When the system arms, you will hear one short siren

sound, or chirp, and see the parking lights flash once. The LED will illu-

minate steadily.

While the system is armed, the LED status indicator will flash approxi-

mately once per second showing that the system is actively protecting

your vehicle. If you hear more than one chirp when arming, refer to the

Diagnostics section of this guide. These extra chirps confirm a malfunc-

tion autobypass.

The security system also can be programmed to arm itself

automatically without a remote (called passive arming). If the system is

programmed for passive arming, it will automatically arm 30-seconds

after the ignition is turned off. Whenever the system is in its 30-second

passive-arming countdown, the siren will chirp once and the lights will

flash once five seconds after countdown has commenced. This is indi-

cated by the rapid flash from the status LED. The system is not actually

armed at that point. The system arms after the 30-second countdown

has elapsed, but the siren will not chirp. The early chirps provide you

with a 25-second warning prior to arming.

When armed, your vehicle is protected as follows:

The LED will flash as a visible theft deterrent.

If the tilt sensor detects the motorcycle is being moved in an

attempt to steal it, the system will immediately trigger the

siren and flash the indicator lights.

This sensor is capable of independently learning the bike’s ini-

tial angles of vertical and horizontal inclination each time it is

parked, ensuring the most accurate tilt (vertical and horizon-

tal) sensing possible.

If a protected switch is opened, the system will immediately

trigger the siren and flash the indicator lights.

The immobiliser prevents the motorcycle’s engine from starting.

nnoottee::

If one of the zone 4 or 5 switch inputs is active or the ignition is

on, the system will not passively arm. Additionally, if one of these

switches is activated or the ignition is turned on, the countdown will

cease, then begin again when the input is removed.

disarming

To disarm the system, press . You will hear two chirps and the

parking lights will flash twice. If the siren chirps four times when disarm-

ing, refer to the Diagnostics section of this guide. This is called Tamper

Alert. If the siren is active (sounding) when the system is disarmed you

will hear three chirps but the system is not disarmed. (Refer to the

Remote Siren Silencing section of this guide.) However, if the alarm com-

pletes the full trigger cycle when disarmed you will hear four chirps.

disarming without a remote

This feature allows you to disarm the system without the remote should

it be lost, damaged, or disabled. In order to disarm without a remote,

you must have the motorcycle’s ignition key, know where the Valet

switch is located, and have the PIN code. Be sure to check with the

installer for the location of the Valet switch.

Turn the ignition On and then enter the PIN code as given in the fol-

lowing example to disarm without a remote.

1. Find the preset PIN code given in this manual.

FOR EXAMPLE: To disarm first enter a PIN code of 4301.

2. Turn the ignition On.

3. Press four times.

4. Then once. This enters the digit 4.

5. Then three times.

6. Then once. This enters the digit 3.

7. Then once. This enters a 0 as there was not a previous

digit entered with .

8. Then once.

9. Then once. This enters the final digit 1.

auto-immobilisation

Immobiliser circuits automatically activate after 30-seconds.

Auto-immobilisation sequence:

1. Turn ignition off or disarm alarm.

2. After 30-seconds the systems Immobilisation circuits activate

and engage the starter and engine interrupts.

3. LED flashes at ½ normal speed.

Disarm the system when immobilised:

Use one of the following methods to turn off

auto-immobilisation.

Turn ignition on and press the button of the trans-

mitter.

Arm the alarm and then disarm the alarm.

Turn the ignition on and enter the system Valet/PIN code.

remote siren silencing

Remote siren silencing is a feature that makes it possible to silence and

reset the system when it is triggering without disarming the system. If

the system is triggered and the siren is sounding, press on the

remote to stop the trigger and return the unit to the armed state. The

system will not disarm, but rather reset. This prevents you from dis-

abling the system should you wish to silence it without visually check-

ing the vehicle. After resetting the system, press again to disarm

the system.

When you remote siren silence, the siren will either chirp 1 or 3 times.

1-chirp indicates that the system is still armed, and that all

zones are inactive and being monitored.

3-chirps indicate that the system is still armed, and that at

least one zone is still active and being bypassed.

NNOOTTEE::

If 3-chirps sound the input that is bypassed will remain bypassed until the

activation ceases.

remote chirp muting (3-button remote only)

To temporarily turn off the arm or disarm chirps, use remote chirp mut-

ing. Simply press on the remote (3-button remote only), and

the confirmation chirp(s) will be eliminated for that one operation only.

The parking lights will flash to confirm the arm/disarm command. If you

want the arm/disarm chirps turned off permanently, please refer to the

User-Selectable Features section of this guide.

remote sensor disable

This can be performed anytime the system is armed. Follow the proce-

dure listed below.

1. Arm the system.

2. Using the remote press and simultaneously.

3. The indicators will flash four times; all Warn Away

zones of

optionally installed sensors are now bypassed (zones two

and three).

4. Using the remote press and simultaneously

again.

5. The lights will flash four more times; All optional sensor

Warn away and Full trigger zones and the Tilt Sensor are

now bypassed

6. The sensor zones will reset when disarmed.

remote start sensor bypass

When the system sees a command to remote start the motorcycle, it

bypasses sensor zones and will continue to bypass these zones until the

remote start shuts down.

NNoottee::

Additional installation options required for Remote Start opera-

tion. See your Directed Authorised dealer for details.

nnoottee::

Sensor disable can be performed at any time after the alarm has

been armed.

auxiliary channel bypass

All alarm sensor inputs will be bypassed while a pulsed or timed auxil-

iary output is active.

panic mode

If you are threatened near your vehicle, you can attract attention by

triggering the system with your remote! Just press for two sec-

onds to enter Panic Mode. The siren will sound and the indicator lights

will flash for the programmed duration (5-minutes maximum). To stop

Panic Mode at any time press on the remote again.

valet mode

You can prevent your security system from automatically arming by

using Valet Mode. This is very useful when washing the motorcycle for

example. In Valet Mode, the security system will not arm, even with the

remote, but any accessory functions will continue to work normally.

To enter Valet Mode:

1. Turn the ignition On.

2. Enter the PIN code as described in the Disarming

Without a Remote section.

3. When you enter the last digit continue to hold the

button for at least three seconds then

release. The LED status indicator will light up and

remain on if Valet Mode has been entered.

The LED status indicator will light steadily if you are entering Valet Mode.

To exit Valet Mode:

1. Turn the ignition On.

2. Enter your PIN code as described previously

3. When you enter the last digit the LED will light up, contin-

ue to hold the button.

4. The system will exit Valet mode and the status LED indicator

will extinguish.

NNOOTTEE::

If One-time Valet is programmed On by your installer, the system will auto-

matically exit Valet mode the next time the ignition is turned on.

remote valet mode

The operations described in this section refer to remote buttons.

Remember, the buttons used in all the instructions in this guide corre-

spond to the Standard Configuration for the 3-button remote. This

may not be how your remote is set up.

To enter Valet Mode, press and simultaneously. The LED

status indicator will illuminate continuously if you are entering Valet

Mode, or will turn off if you are exiting Valet Mode.

NNoottee::

The LED will turn off when the ignition is ON.

instant auto-arming bypass

This will bypass the auto arm feature once only.

1. With the key, turn the ignition on, then off within two seconds.

2. The siren will chirp once to confirm auto arming bypass.

3. The system will not auto arm.

During auto arming bypass the system will not auto-activate the acces-

sory output when using the remote to arm the system.

nuisance prevention

circuitry

Your system has Directed’s Nuisance Prevention

Circuitry (NPC

). It pre-

vents annoying repetitive trigger sequences due to faulty switches or

environmental conditions such as thunder, jackhammers, airport noise,

etc.

Example: If the alarm triggers three times within a 60-minute period

and each time the same sensor or switch triggers the alarm, NPC

will

interpret those triggers as false alarms. After the third trigger, NPC

ignores, or bypasses, that sensor or switch (along with any other sen-

sors or switches sharing the same zone) for 60 minutes.

If the bypassed sensor tries to trigger the system while it is being

bypassed, the 60-minute bypass period will start over. This ensures that

a sensor that continually triggers will remain bypassed.

nnoottee::

The system will revert to normal auto arming when the system

sees the ignition on for at least three seconds and then turned off, or

the system is armed and disarmed with the remote.

NPC

is On/Off programmable. See your dealer and the Programming

section of this guide for more information.

multiple event total recall

This will report the last eight system triggers in reverse chronological

order.

1. Press and hold of the Valet switch.

2. While still holding , arm and disarm the system, then

release the button.

3. The LED will start to flash to indicate the most recent trigger

and proceed down to the eighth trigger. For more informa-

tion, please refer to the Table of Zones section of this guide.

battery back-up siren

The built-in battery back-up siren protects the system if a thief discon-

nects power and/or cuts or tampers with the power supply wires while

the system is armed. If system power is lost the siren will sound for five

minutes and then reset.

nnoottee::

Arming and disarming the system does not reset this function.The

only ways to reset a bypassed zone are for it to not trigger for 60 min-

utes, or to turn on the ignition. If testing your system, it is important to

remember that the NPC

programming can cause zones to be

bypassed and appear to stop working. If five chirps are heard when

disarming, NPC

has been engaged. If you wish to clear the NPC

memory, turn the ignition key on.

diagnostics

The microprocessor at the heart of your security system is constantly

monitoring all of the switches and sensors that are connected to it. It

detects any faulty switches and sensors and prevents them from dis-

abling the entire system. The microprocessor will also record and report

any triggers that occurred during your absence.

arming diagnostics

If the system is armed while an input is active (sensor triggering, etc.)

the unit will chirp once when arming and then once more five seconds

later. This is called Bypass Notification. Refer to the Arm/Disarm Diagnostic

Chart for bypass notification details.

You are able to see exactly which zone is causing the bypass notification by

disarming the system and turning the ignition on. The zone will be report-

ed by flashing the active zone 5-times. See the Table Of Zones.

The security system will ignore the input that was active when the sys-

tem was armed, until the input goes away. 3-seconds later the system

will monitor that input normally. For example, if the protective switch

is active, you will hear one Bypass Notification chirp (the protective

switch is bypassed from the alarm system). Once the protective switch

is reset, then 3-seconds later the system resumes normal monitoring of

this switch.

disarming diagnostics

Extra disarm chirps are the Tamper Alert. If four chirps are heard when

disarming, the system was triggered in your absence. If four chirps are

heard, the LED status indicator will indicate which zone was triggered

when the ignition is turned on and will repeat 5-times (refer to the

Arm/Disarm Diagnostic Chart and Table of Zones section). The system

will retain this information in its memory. Refer to the Multiple Event

Total Recall section of this guide.

arm/disarm diagnostic chart

Refer to the table of zones to identify the last zone triggered.

Action No. of Chirps Description

Arm 1 System armed

Arm 1 (3-sec. pause) 1 System armed with zone

active and bypassed

Disarm 2 System disarmed

Disarm 4 System disarmed with tamper alert

High Security 1 System silenced, but still armed, and

Disarm all zone inputs are inactive and

(siren on) monitored.

High Security 3 System silenced, but still armed, and

Disarm a zone is still active and bypassed.

(siren on)

Disarm 5 System disarmed with a zone in NPC.

table of zones

The zone number is the number of LED flashes used by the system to

identify a specific input. The standard input assignments are listed

below, along with spaces to write in any optional sensors or switches

you have had installed. If a Warning Zone response is triggered, the LED

will not report it.

anti-code grabbing (ACG)

This unit features Anti-Code Grabbing (ACG) with Random Code

Encryption. This means the receiver and remotes each use a mathemati-

cal formula called an algorithm to change their code each time the

remote is used. This technology has been developed to increase the secu-

rity of the unit. The control unit knows what the next codes should be.

Zone - Number Dealer-Installed

of LED Flashes Description Options

1 Tilt Sensor

(Built-in Tilt Sensor)

2 Auxiliary sensor 1

input

3 Auxiliary sensor 2

input

4 Normally Closed

input (from protective switch)

5 Optional switch input

6 Ignition Input

7 12 V Power interruptions

high frequency

Your system transmits and receives at 433 MHz. This provides a cleaner

spectrum with less interference and a more stable signal.

rapid resume logic

This security system will store its current state to non-volatile memory.

If power is lost and then reconnected the system will recall the stored

state from memory. This means if the unit is in Valet Mode and the bat-

tery is disconnected for any reason, such as servicing the car, when the

battery is reconnected the unit will still be in Valet Mode. This applies

to all states of the system including arm, disarm, autoimmobilised and

Valet Mode.

power saver mode

When in Valet mode, the LED will turn off 1-hour after enter-

ing Valet mode.

After 24 hours in the armed state, the LED will decrease the

flash rate to

/2 the normal rate; after 48 hours it will decrease

/4 the normal rate.

After 96 hours of no activity (arm, disarm, or alarm trigger) the

alarm enters sleep mode. The alarms receiver, and LED turn off

to save as much battery power as possible. The system is

drawing next to no current in this mode.



To exit sleep mode turn the ignition on and the siren will

chirp 10 times (5-seconds) before the siren sounds.

Disarm the system with the remote or by entering the

PIN code with the Valet switch.



If any other input is activated when in sleep mode, the

system will wake up and trigger the alarm immediately.

system sensors and adjustments

Your system was installed with an integral Tilt sensor. Optional sensors

such as the 504D Double-Guard Shock sensor or 508D Dual-Zone

Proximity sensor may also have been installed.

For adjustments to all sensors/options, please return your motorcycle to

the installing Directed

dealer.

programming options

Programming options control what your system does during normal

operation, and require few or no additional parts. However, some may

require additional installation labor.

Following is a list of the program settings, with the factory settings in bold:

Autoarming on or autoarming off of the alarm : Automatic

arming 30-seconds after ignition turned off.

Arming/disarming confirmation siren chirps off, loud or

quiet. The siren arm/disarm chirps can be either full volume,

6 decibels quieter, or turned off completely.

Panic mode: on/off.

Siren duration: 30/60/90 seconds.

Set PIN code: Allows you to enter your own PIN code, over-

writing the factory PIN code.

Siren tones: The output of the siren consists of six different

tones in sequence. Any of these tones can be eliminated, result-

ing in a unique, easily identifiable siren sound.

NPC

: Nuisance Prevention

Circuitry on/off. Inhibits false

alarming if a protective zone repetitively alarms.

Remote Valet: on/off.

Reset settings to default (except for PIN code)

New remote learn features: Allows programming individual

transmitter channels to custom configurations. Refer to User

Selectable Features Descriptions - Column Three.

Clear all Remotes: Removes all remote controls from memory.

manual programming instructions

It is a good idea to document changes by taking note of all feature

changes made in programming mode.

To enter the User Selectable Features programming:

1. Ignition on - Turn the ignition to the on/run position or start

the engine.

2. Enter PIN - Your PIN code.

FOR EXAMPLE: To enter a PIN code of 4301—

Press four times,

then once. This enters the digit 4.

then three times,

then once. This enters the digit 3

and then once. This enters a 0 as there was

not a previous digit entered with .

then once,

and then once. This enters the final digit 1.

3. Hold/Chirp/Release - After entering the PIN code, press and

hold until a chirp is heard and the LED turns on, then

release the button. You have now entered the feature selec-

tion position of the User Selectable Features grid.

4. Column select - Press and release the same number of

times as the desired column. After a pause the siren will

chirp the same number of times as the selected column for

confirmation (e.g. 3-chirps means column 3 of the features

is selected).

5. Feature select - Press and release the same number of

times as the desired row. The siren will chirp with each press.

The feature can now be changed using the remote control.

6. Feature change - Press the button on the remote. If

the system chirps once, the feature has just turned off or

switched to the first setting in the grid slot for this feature;

if the system chirps twice, the feature has just turned on or

switched to the second setting in the grid slot.

If the feature has more than two settings, continue pressing

the on the remote to toggle through the settings

(e.g. if the feature has 1 through 5 settings, the system will

chirp 1 through 5 times for each setting selected). If you

continue to press and release the remote the feature setting

will wrap back around to the first setting again. (e.g. if the

feature has 3 settings you will hear, 1 chirp, 2, chirps, 3

chirps, 1 chirp, 2 chirps, etc).

To advance to another feature in the same column, press

the same number of times as the desired feature with-

in 60 seconds; to change a feature in a different column

begin at step 5 by entering the column number first and

then the feature select in step 6.

7. Exit programming - To exit programming mode turn the igni-

tion off or wait 60 seconds without pressing the Valet but-

ton. The siren will chirp three times to indicate programming

mode has been exited.

After you change a feature setting, the feature counter is reset to zero.

Hence, to change another feature in the same column you must press

the button the same number of times as indicated in the chart

below.

nnoottee::

Refer to the Feature Descriptions sections of this guide for impor-

tant notes and descriptions of the system features and programming.

user selectable features

user selectable features descriptions - column one

add new remote (for 2-button in-key and 3-button remotes only)

Auto-learn new remote controls to the system (one at a

time) in the standard button configuration. For more infor-

mation, refer to Note #1 in Programming Notes section.

First

Press

Then

Press

Add new remote

(autolearn)

Set PIN code New remote learn

arm/disarm only

Auto arm

on/off

Select siren

sounds

New remote learn

accessory output

Chirps

off/loud/quiet

NPC on/off

New remote learn

silent mode

Panic

on/off

Remote valet

on/off

New remote learn

remote valet

Siren Duration

30/60/90 seconds

Reset to default

(except transmitter

and PIN code)

New remote learn

sensor disable

Not used Clear all remotes

from memory

Not used

auto (passive) arm - on/off

On: When the system sees the ignition turn off, it will begin

a 30-second countdown before arming itself. The count-

down is indicated by the system LED rapid flashing. After the

first five seconds, you will hear one chirp and the indicators

will flash. The system will arm 25 seconds later.

Off: The transmitter must be used to arm the system.

chirps - off/loud/quiet

Off: Chirps will not sound when arming/disarming the sys-

tem (with the exception of arm/disarm diagnostic chirps and

programming chirps).

Loud: Chirps will sound when arming/disarming the system

at full volume.

Quiet: Chirps will sound when arming/disarming the system

but at a lower volume than normal (with the exception of

arm/disarm diagnostic chirps and programming chirps).

panic - on/off

Allows the remote to activate Panic Mode. The siren will sound for 30

seconds.

On: The system will enter Panic Mode if the arm/disarm but-

ton is pressed for more than 2 seconds.

Off: Panic Mode is disabled.

siren duration - 30/60/90

The system will sound the alarm for the programmed dura-

tion (30/60/90 seconds) during an alarm trigger or when the

system is put into panic mode.

user selectable features descriptions - column two

set pin code

This feature allows you to change your personal PIN code.

For more information, please refer to the PIN Programming

section of this guide. Factory default PIN number is 2.

select siren sounds

This feature allows you to select which siren sounds will be played back

when the alarm is triggered. Use the following procedure to set this

feature:

1. Enter the feature.

2. Press the button of the remote to begin the playing

of siren sounds.

3. Siren will generate each sound for 5-seconds. There are 6 in

total.

4. To add the sound press the button on the Valet switch

while that sound is playing.

5. To delete the sound press the button on the Valet

switch while that sound is playing.

nnoottee::

After selecting or deleting a sound the siren will immediately play the next

sound. If no sounds are selected by pressing the or button the system

will remain in its previous setting.

NPC

on/off

Nuisance Prevention

Circuitry (NPC

) stops repeated triggering of the

same zone. If one zone is triggered three times in one hour, that zone

is bypassed for one hour, starting from the time of the third trigger.

During that hour, if the system detects a trigger on that zone again, the

system resets the one hour timer. If one hour passes and the zone has

not triggered again, the zone is activated and can trigger the system

again. NPC

monitors sensor inputs and the door trigger. If NPC

turned off, the system will respond to repeated triggers on the sensor

inputs and will do so indefinitely. Some states have laws regulating how

many times a security system can trigger before it is considered a nui-

sance and the vehicle is towed away.

remote valet on/off

This feature allows you to set remote Valet on or off.

reset to default

This feature allows you to restore the programming to factory defaults,

except for the PIN code and remote controls programmed into the system.

user selectable features descriptions - column three

The features in this column pertain to programming individual remote

channels in custom configurations. Following is an explanation of the

features. To program specific functions to a different button, enter the

function you are programming after the chirp confirmation. Press the

button with which you wish to control that feature; the system will

chirp to confirm that it has learned the new button.

arm/disarm only

The remote control channel programmed into this feature

will arm/disarm the system only.

accessory (-) output

The remote channel programmed into this feature will acti-

vate the accessory output.

silent mode

The remote channel programmed into this feature will

arm/disarm the system, but the siren will not chirp.

remote valet on/off

The remote channel programmed into this feature will make

the system enter/exit valet mode.

sensor disable

The remote button programmed for this feature will make

the system bypass the sensors for one arming cycle only. On

the next arming cycle, zones 1, 2, and 3 will be reinstated.

clear all remotes

This feature will erase all remote codes from the system

memory. This feature is convenient for erasing any remotes

that have been lost, stolen, or incorrectly programmed into

the system.

After entering this feature press the button on a

remote that is programmed to the system; the siren will

chirp twice to indicate that all remotes have been erased

from memory.

nnoottee::

When programming a remote control to custom configuration, a

remote button must first be learned to the arm/disarm. The rest of the

features in this column can then be learned.

A remote button can only be learned to one designated feature. That

is, if the lock/unlock button is programmed for armed/disarmed (fea-

ture 1 in column 3), it cannot be programmed for another additional

feature listed in column 3 of the User Selectable Features.

pin programming

A PIN code can have one to four digits; each digit can be from 0-9.

Programming Procedure

1. Enter the feature location (column 2, row 1) in the user-

selectable programming grid.

2. Immediately press and release of the Valet switch.

3. Select each digit by pressing 1-9 times, and then press

to enter the number into the system. To enter a zero,

press only.

To program a PIN code of 1032:

A. Press and release once and once. You will

hear one chirp.

B. Press and release once. You will not hear a chirp

after programming a zero.

C. Press and release three times, and then press

once. You will hear three chirps.

D. Press and release two times, and then press

once. You will hear two chirps.

4. Wait for two siren chirps after a five second pause or five

seconds after the last digit has been entered if using less

than four digit code number.

5. Turn off the ignition; the siren will chirp three times.

6. The programming mode is now exited.

nnoottee::

A PIN code cannot begin with a zero.

PIN Code Confirmation Procedure

Begin this procedure within 15 seconds of finishing the programming

sequence or the new code will not be set.

1. Turn on the ignition.

2. Enter the new PIN code.

3. Press and hold for three seconds.

LED turns on: New PIN code is learned and program-

ming is complete.

LED stays off: New PIN code is not learned and the sys-

tem reverts to the old PIN code. Repeat the program-

ming sequence.

glossary of terms

Control Unit:

The "brain" of your system hidden somewhere on the

motorcycle where it is difficult for a thief to access. It houses the micro-

processor which monitors your vehicle and controls all of the system's

functions. The Merlin 3000 control unit houses the battery backup

siren and Tilt sensor.

Input

: A physical connection to the system. An input can be provided

by a sensor, switch or through an existing system on the motorcycle.

LED

: Blue light mounted somewhere on the motorcycle. It is used to

indicate the status of your system. It is also used to report triggers and

faults with the system.

Tilt Sensor: A sensor integral with the control module which senses if

the angle of the motorcycle has changed.

Remote

: Hand-held transmitter which operates the various functions of

your system.

Trigger or Triggered Sequence: This is what happens when the alarm

"goes off" or "trips." The triggered response of your system consists

of the siren sounding and indicators flashing for 30-seconds.

Valet Switch

: A small two-button switch mounted somewhere on the

motorcycle. It is used to override the alarm when a remote is lost or

damaged, or to enter or exit Valet mode and for system programming.

Zone

: A zone is a separate input that the alarm can recognize as

unique. Each input to the system is connected to a particular zone.

security & convenience expansions

Here we have listed only some of the many expansion options avail-

able. Please contact your dealer for a complete list of all the options

available to you.

Field Disturbance Sensor: An invisible dome of coverage is

established by installing the 508D "radar" sensor. Your security

system can then react to any intrusions on the perimeter of the

field with a warnaway response and if anyone were to intrude

inside the dome the full alarm would sound. Ideal for warning

people away from the motorcycle.

Shock Sensor: The 504D dual-stage shock sensor can be

installed to provide warn-away and alarm protection for your

motorcycle if impacts are detected.

Remote Start

The 561T remote start system to provide engine

warm up and battery recharging.

CCuutt aalloonngg ddootttteedd lliinnee aanndd ffoolldd ffoorr aa qquuiicckk aanndd eeaassyy rreeffeerreennccee ttoo kkeeeepp iinn yyoouurr ppuurrssee oorr wwaalllleett..

✂✂

QUICK REFERENCE GUIDE

remote functions

function

3-button 2-button

remote remote

Arm/Disarm/Panic

Accessory Output

Silent Arm/Disarm N/A

Sensor Disable

Remote Valet

N/A

■ Transmit "Silent Arm/Disarm" to delete the arm/

disarm chirps for one operation only.

■ Transmit "Sensor Disable" once to bypass the sensor

warn away chirps, twice to bypass sensors entirely.

Note: The system must be armed first.

CCuutt aalloonngg ddootttteedd lliinnee aanndd ffoolldd ffoorr aa qquuiicckk aanndd eeaassyy rreeffeerreennccee ttoo kkeeeepp iinn yyoouurr ppuurrssee oorr wwaalllleett..

✂✂

system disarm

To disarm the system without a transmitter, turn the

key to the ON position and enter your PIN code.

valet mode entry

To enter Valet Mode without a transmitter, turn the

key to the ON position and enter your PIN code.

Continue to hold on the Valet switch for five

seconds.

pin code entry

On the Valet switch, press the number of times

corresponding to the first digit of your PIN, then

press once. Press to enter a zero. Repeat this

for each digit of your PIN code.

There is a space provided below to note your pin

code for future reference.

Vista, CA 92081

www.directed.com

G225T 10-05

The company behind this system is Directed Electronics.

Since its inception, Directed Electronics has had one purpose, to provide consumers with

the finest vehicle security and car stereo products and accessories available. The recipient of

nearly 100 patents and Innovations Awards in the field of advanced electronic

technology, Directed is ISO 9001 registered.

Quality Directed Electronics products are sold and serviced throughout North America

and around the world.

Call

((880000)) 227744--00220000

for more information about our products and services.

Directed Electronics is committed to delivering world class quality products

and services that excite and delight our customers.

Directed Electronics Merlin 3000 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info