798222
14
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
GB-4
English
1.3
Installation of the pipe connections:
ATTENTION!
When connecting the pipe system to the heat exchanger, ensure that it is
not subjected to stress or strain by the pipe system! Clean the pipework
before installation on the heat exchanger!
Heavy pipework must be supported to prevent strong forces from
being applied on the heat exchanger.
Use flexible connections to prevent vibrations on the heat ex-
changer and to compensate for the expansion of the pipes
caused by temperature fluctuations on the heat exchanger (ten-
sion-free lengthways installation).
NOTE
To guarantee adequate venting, the bleeder valves should be mounted in
the highest position in the flow direction of the medium (preferably on a
pressure vessel). Isolating valves can be used on all connections of the
heat exchanger to make them easier to open when necessary!
Threaded pipe connections:
During installation, ensure that these connections do not turn
while pipe connectors or flanges are being mounted.
Turning the threaded pipe connections could damage the seal in
the heat exchanger, which acts as a seal against the rear side of
the pipe connection!
Flange connections:
If the connection is lined with rubber, the lining also acts as a
flange seal. The connection flange should be connected directly
to the end plate using the designated tapped holes. The screws
should be tightened evenly - do not tighten excessively, as this
could overwind the threads cut in to the frame plate.
If loose support flanges are mounted on the heat exchanger, a
suitable seal is required for sealing the flange.
Commissioning:
ATTENTION!
Start the cold circuit first, followed by the hot circuit.
Purge the system completely by closing the isolating valves be-
tween the pump and the heat exchanger (if a valve is installed in
the return of the heat exchanger, open it).
Then start the brine circulating pump and open the valves in the
flow to the heat exchanger gradually.
If necessary, purge again and repeat the above steps for the sec-
ondary circuit if this is also a closed circuit.
1.3 Connecting the heat generator and brine (intermediate) circuit pump:
Fig. 1.3: Connecting the heat generator and brine (intermediate) circuit pump
SI 50TU
WSI 65TU
SI 75TU
WSI 90TU
SI 90TU
WSI 110TU
Heat generator circuit pump
M 16:
Magna Geo 32-
100VDC Magna3 40-80F Magna3 65-80F
Intermediate circuit pump
M11: Magna3 65-80F Magna3 65-100F Magna3 65-100F
Well pump
M11: To be provided on-site
Domestic hot water preparation
Heating circuit(s)
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Dimplex ZKP 65F-25 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Dimplex ZKP 65F-25 in de taal/talen: Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 3.56 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info