706539
8
Verklein
Vergroot
Pagina terug
1/41
Pagina verder
Fitting Product - see Fig. 4 - 11
There are three possible mounting meathods
1. Surface Mounting
2. Partial Recessed (Not on 74" Models)
3. Flush Mount
Surface Mounting (34" & 74" Models)- see
Fig. 4 & 5
CAUTION: Two people will be required for various steps
of this procedure.
WARNING: Ensure that the circuit on which the replace
is to be installed has the power cut off at the service panel
until installation is complete.
1. Determine the mounting location of the unit so that
the wall-mounting bracket can be installed into a
minimum of 2 wall studs for the 34" Models and 4 wall
studs for the 74" Models
!
NOTE: It is recommended that the mounting bracket
be installed 56 in. (142 cm) off of the ground to maintain an
optimized viewing angle of the ame.
2. Hold the wall mounting bracket, with the bubble level
on the top, on the wall so that the bubble on the level
is centered between the two black lines.
3. Mark the 4 mounting screw locations, on the wall,
ensuring that the wall bracket stays level (Fig. 4)
marked (A).
4. In locations where the screws are being installed only
into drywall, install the supplied wall anchors before
installing the screw (predrill if required).
5. Secure the wall bracket to the wall using the supplied
1 ½ in. (3.8 cm) mounting screws and washers into the
wall and/or wall anchors.
6. Install the bottom support bracket to the wall centered
with the wall mounting bracket, using the appropriate
mounting hardware, 13 ¾" (350 mm) below the wall
mounting bracket (Fig. 4) marked (B).
7. Remove the center screw from the bottom of the
replace. (Fig. 5)
8. Hang the replace from the bracket.
9. Install the previously removed screw through the
bottom support bracket into the replace.
10. Refer to Front Glass Installation section for nal
installation procedures.
Surface Mounting (50" Models) - see Fig. 6 & 7
CAUTION: Two people may be required for various
steps of this procedure.
1. Choose a location which has a minimum of two wall
studs available for mounting.
2. Choose your method of supplying power to the unit:
Plug in to an existing outlet or install an outlet nearby.
Hard wire the replace.
WARNING: Do not attempt to wire your own new outlets
or circuits. To reduce the risk of re, electric shock or injury
to persons, always use a licensed electrician.
WARNING: Ensure that the circuit on which the replace
is to be installed has the power cut off at the service panel
until installation is complete.
3. Remove the partially reective glass from the replace:
Lay replace on its back.
Remove two Phillips screws from each of the two glass
brackets (Fig. 6) marked (A).
Remove glass brackets (Fig. 6) marked (B).
With one hand keeping pressure on the partially
reective glass, tilt the replace upright and slightly
forward to allow the partially reective glass to fall out
of the inside framing.
CAUTION: Partially reective glass is not tempered. Do
not bump or drop the partially reective glass to avoid
breakage and personal injury.
Remove partially reective glass from replace.
4. Position the replace on a wall in the position where
it will be mounted (Fig. 7). Use a bubble level (one is
supplied) to ensure that replace is level on the wall.
5. Ensuring that at least two key-holes line up with a wall
stud (key-holes are spaced at 4 in. (10.2 cm) centers)
(Fig. 7) marked (A), mark the location of four screw
locations on the wall (through key-holes).
6. Remove fireplace from wall and store in a safe place
away from traffic.
7. Where marked screw locations do not line up with a
wall stud, insert (screw in) one of the two supplied wall
anchors (predrill if required). Repeat if only two screws
line up with a wall stud.
8. Screw all four supplied #8, 1 ½ in. (3.8 cm) square head
mounting screws and washers into the wall and/or wall
anchors leaving ¼ in. (6.5 mm) of thread.
9. Align chosen key-holes with screws and hang replace
on the wall. Screw heads and washers will t through
key-holes and replace will slide down into place
(screws will slide into narrow part of key-holes).
10. Tighten all four mounting screws down on replace
chassis.
11. Screw the two supplied #8 square head screws through
two of the permanent mounting holes (Fig. 7) marked
(C) which align with a wall stud.
12. Carefully replace and install partially reflective glass
and glass brackets using screws from step 1.
13. Refer to Front Glass Installation section for nal
installation procedures.
Partial Recessed (Not possible on 74" Models)-
see Fig. 8 & 9
CAUTION: Two people may be required for various
steps of this procedure.
1. Prepare a wall with a framed opening for the correct
model (Fig. 8)
34" Models: 30 ½ in. (77.5 cm) wide x 16 ½ in. (42 cm)
high
50" Models: 46 ½ in. (118.1 cm) wide x 16 ½ in.
(42 cm) high
!
NOTE: The sizing has allowed for ¼ in. (6.4 mm) around
the replace insert for ease of installation. This replace
does not require any additional venting.
2. Choose your method of supplying power to the unit:
Plug in (you may run the power cord out of the framed
wall opening to an existing outlet or install an outlet on
a nearby wall stud within the wall).
Hard wire the replace.
WARNING: Do not attempt to wire your own new outlets
or circuits. To reduce the risk of re, electric shock or injury
to persons, always use a licensed electrician.
WARNING: Ensure that the circuit on which the replace
is to be installed has the power cut off at the service panel
until installation is complete.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Dimplex Wickson bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Dimplex Wickson in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools, Noors als bijlage per email.

De handleiding is 9,03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info